Page 81 of AES Ham Radio Catalog by AES Amateur Electronic Supply

ANTENNA ACCESSORIES 105 1-800-321-3594 OH 1-800-327-1917 FL 1-800-634-6227 NV Email Your Questions to info@aesham.com AES LADDER LINE 450 OHM 100 18 ga. 100' insulated... $19.99 450 OHM 14 100 14 ga. 100' insulated 39.99 450 OHM 1000 18 ga. 1000' insulated 149.99 450 OHM 14 1000 14 ga. 1000' insul 299.99 WHITE NYLON ROPE NR-100 100' roll, antenna guy rope ...... $6.99 NR-1000 1000' roll, antenna guy rope... 50.99 N CONNECTOR N CONNECTOR Male connector for Belden 9913 and 8214 coax........................................ $4.99 PREASSEMBLED COAXIAL HOOK-UPS 8X-1.5ST 1.5' RG-8X, silver-tef. PL-259s $9.99 8X-3ST 3' RG-8X w/silver-teflon PL-259s 10.99 8X-6ST 6' RG-8X w/silver-teflon PL-259s 12.99 8X-12ST 12' RG-8X, silver-teflon PL-259s 15.99 8X-25ST 25' RG-8X, silver-teflon PL-259s 22.99 8X-50ST 50' RG-8X, silver-teflon PL-259s 32.99 8X-75ST 75' RG-8X, silver-teflon PL-259s 40.99 8X-100ST 100' RG-8X, silver-tef. PL-259s 47.99 213-25ST 25' RG-213, silver-tef. PL-259s 34.99 213-50ST 50' RG-213, silver-tef. PL-259s 50.99 213-75ST 75' RG-213, silver-tef. PL-259s 72.99 213-100ST 100' RG-213, sil.-tef. PL-259s 90.99 Van Gorden Engineering BALUNS INSULATORS Hi-Q 1:1 or Hi-Q 4:1 Baluns For dipoles, yagis, inverted vees and doublets. Provides 1:1 or 4:1 impedance ratio for matching unbalanced coaxial cable to balanced antennas. Covers 3-40 MHz with a 1.5KW rating. Reduces feedline radiation for more power into antenna, and reduced TVI/BCI problems. Builtin DC ground reduces static noise and provides some lightning protection. Convenient SO-239 connector and center support eye hook; weatherproof ea. $18.99 ANTENNA CENTE Hi-Q Antenna Center Insulator Insulator only, no balun. Replaces egg-type center insulator. Small, rugged, lightweight, weatherproof, SO-239 connector, center supporting eye hook .................. $9.99 ANTENNA END IN End insulators pair $6.99 DOG BONE Antenna insulator......... each 99 See Price Guide for Cable X-perts pricing. PENETROX A Conductive Grease Highly recommended for use on aluminum-to-aluminum and aluminum-to-copper connectors, on bare conductors, and bus bars. Assures long term high conductivity joint by sealing out air and moisture to prevent corrosion and reformation of oxide film. Apply to mating pieces of antenna components, tubing, etc. during assembly to provide a non-corrosive, low resistance and air tight seal. Makes later disassembly effortless ................................ (4oz bottle) $12.99 STUF Dielectric Water-proof Connector Filler Seals out moisture. High purity macroscopic foam that dielectrically simulates the coaxial cable core. Fill coax connectors and tighten. The filler material hydraulically channels into all connector voids and points of moisture entry. Non-hardening, easy to remove. No silicone, or other additives to harm coax cable material ........................................ (tube) $5.99 COPPERWELD Antenna Wire Forge-welding makes the two metals inseparable! Solid bare copper-over-steel wire the best for antennas. Very strong, the steel core has very little stretch and long service life. The copper covering provides low RF resistance and solders easily. 12, 14 or 18 gauge. AN-122 100 ft. #12............................... $39.99 AN-123 150 ft. #12 ................................. 49.99 AN-124 250 ft. #12 ................................. 79.99 AN-126 500 ft. #12............................... 139.99 AN-128 1000 ft. #12............................. 239.99 AN-142 100 ft. #14 ................................. 29.99 AN-143 150 ft. #14 ................................. 39.99 AN-144 250 ft. #14 ................................. 49.99 AN-146 500 ft. #14 ................................. 89.99 AN-148 1000 ft. #14............................. 169.99 AN-181 250 ft. #18................................. 24.99 AN-182 500 ft. #18 ................................. 39.99 MEADOW RIDGE PRODUCTS, INC. Copper for permanence Steel core for strength UNV 104 Hand Moldable Plastic for Antenna Component Protection The quick and effective way to seal and protect all types of coaxial fittings, baluns, antenna parts and connectors. Simply wrap it on like regular tape, then mold it to any shape. It adheres tightly to metal, vinyl and polyvinyl coax outer jackets. Stays flexible and sealed at any temperature for years to resist moisture penetration and deterioration. Its permanent flexibility makes it possible to remove and reinstall fittings, then reseal by reforming the same material. Non-toxic and non-contaminating roll, 1/2"w x 60" .......... $3.99 WRAP! MOLD! Coax Connector Protection Products ANTENNA WIRE

[close]