Page 90 of AES Ham Radio Catalog by AES Amateur Electronic Supply

MISCELLANEOUS ACCESSORIES 114 Order Toll Free at 4 Locations Nation-Wide 1-800-558-0411 WI Browse Our Store On-Line at www.aesham.com AES 281 Communications Speaker Features a rugged 3 inch Mylar cone speaker mounted in a welldesigned baffle. Improves speech intelligibility in the 600 to 4000 Hz range while reducing undesirable noise, static and hum. Dim: 3.75"h x 3"w x 2.25"d ....................... $12.99 382 Deluxe Amplified Speaker Excellent for QRPers, base station HTs or rigs requiring more volume. A quality 3 in. speaker provides plenty of audio. All metal cabinet, rubber feet and vinyl clad cover. Uses 9V battery or 110V AC with optional MFJ-1312D. Cable included. Dim: 3.5"h x 1.75"w x 4.5"d.. $39.99 624D Deluxe Hybrid Phone Patch Interfaces a telephone line with a rig. Jumper selectable for all 8-pin Kenwood, Icom, Yaesu and Alinco transceivers. Adapts to work with virtually any rig. Uses 12VDC, 9V battery or 110VAC with optional AC adapter. Dim: 8"w x 2"h x 6"d................ $119.99 616 Speech Intelligibility Enhancer Provides approximately 20dB audio frequency boost or cut to four overlapping octave ranges centered at 300, 600, 1200 2400 Hz. Improves ability to hear and understand SSB, FM, AM, CW QSOs by adjusting response levels to match hearing response for best clarity, then equalizing perceived loudness to each ear. Built-in dual, 2.5W, audio amps; front panel jack; speaker on/off switch; 2 selectable transceiver inputs; bypass switch. Use with rig or PA. Dim: 10"w x 2.5"h x 6"d; requires 12 VDC ..... $169.99 762 Step Attenuator Push-button selection of up to 81dB attenuation in 1dB steps up to 170 MHz (usable to 500 MHz). 50 ohms; rated 250 mW maximum; BNC connectors with SO-239 adapters; metal cabinet. Dim: 6.5"w x 2.5"h x 1.5"d.... $69.99 1703 Antenna/Transmitter RF Safety Switch Select between two rigs and two antennas. Prevents rig from transmitting if not terminated. Range: 1.8-30 MHz; up to 300W SSB/150W CW, 50-75 ohm coax. Metal cabinet with mounting tabs. Dim: 6.5"w x 2.5"h x 1.5"d............... $19.99 890 DX Beacon Monitor Use as an aid to check band conditions worldwide in just three minutes. It requires no connection to a transceiver. The beacon monitor is a stand alone timing device using a microprocessor and built-in WWVB atomic clock to keep track of the beacon activation sequence. LED indicators positioned across a world map show which of the 18 beacons is active at any given time. Storing the beacon frequencies in transceiver memory allows quick switching as one listens for beacon transmissions. When a beacon is heard on any of the frequencies, that band is open to the location indicated by the corresponding LED. Requires 12VDC or 110VAC with the optional MFJ- 1312D. Dim: 6.75"w x 5.25"h x 3"d........... $99.99 HEAR IT Incorporates DSP technology that is fully adaptive to any change in background or man-made noise levels, and effectively attenuates it up to -20dB. This dramatic drop in noise level results in clearer and less fatiguing audio. The Hear it has the capability to reduce noise equal to, or better than, DSP systems built into several popular radios. If your radio already has DSP, the Hear it will provide additional improvement in copy. If it doesnt have DSP, there will be a huge improvement in readability. Eight user-selectable noise cancelling levels, or cancelling can be switched off entirely. Plugging headphones or another speaker into the audio bypass jack mutes the speaker, but retains DSP noise reduction. A built-in amplifier provides 2.5W of audio power. Requires 12-28VDC @ 500mA. Includes a 6.5 ft. lead with 3.5mm mono plug. Dim: 4.5"w x 2.75"h x 2.25"d .... $159.99 IN LINE MODULE Provides the same audio enhancing and noise reduction features as the Hear it speaker above, but without the speaker. Built-in 5W audio amplifier for your station speaker. Has 3.5mm mono and RCA phono audio input/ouput jacks and headphone jack. Requires 12-24VDC 500mA. Includes 3.5mm to 3.5mm audio cable and fused power leads. Dim: 6.75"w x 3.35"h x 1.4"d; 1 lb...... $199.99 1263 Microphone Control Center Mix and match any two microphones to any two transceivers. The microphones or transceivers can have 8-pin round or modular connectors. Eliminates swapping connectors. Plug in a PTT foot switch or let a computer or voice keyer control the PTT line. Also plug in headphones and an external speaker. The headphones are always active and a volume control eliminates the need to readjust the rig's volume when switching the speaker on. An input jack and on/off switch are provided to insert external audio into the microphone audio input line. Great for inputting sound card, SSTV, AFSK, TNC and other audio sources. Includes two 8-pin round radio cables. Dim: 6"w x 1.5"h x 5"d ................... $99.99 MISC. 1020C Indoor Active Antenna Covers 300 kHz to 30 MHz in 5 bands. Telescoping (21'') antenna provides good receive signal strength. Functions as a preselector when using an external antenna. Improves selectivity, reduces noise. Uses 9V battery, 9-18VDC or 110V. Dim: 5"w x 2"h x 6"d... $79.99 1024 Outdoor Active Antenna Covers 50 kHz to 30 MHz. A separate RF amplifier module with 54 in. whip antenna mounts outside and connects by supplied 50 ft. coax to the control inside. Control contains gain control and 20dB attenuator. Select between two receivers and auxiliary antenna. Auxiliary input and output jacks. Uses 12VDC or 110VAC with adapter. Dim: Control 6"w x 2"h x 5"d; Module 3"h x 4"w x 4"d................... $129.99 1040C All-Band Preselector Improves reception while rejecting out-of-band signals and images on four bands: 1-3, 3-7, 7-18 and 18-54 MHz. Low-noise 20dB gain MOSFET amplifier with a gain control and 20dB attenuator handles a wide range of signal levels. Usable with transceivers up to 125W; a relay automatically bypasses the amplifier on transmit. Push buttons select 20dB attenuator, two antennas, two radios, power On/Off. Controls for delay, gain, band and tune. Unit is bypassed when off. Requires 9-18VDC or MFJ-1312D ($14.99).................................. $99.99 1024 1020C 762 1703 70-14 An affordable solution that will deliver top of the DSP Noise Reduction for ANY transceiver. The ADSP 2 speaker has two convenient push button switches. One button toggles between 0, 13dB or 26dB of noise cancellation and the second selects 1 of 3 bandpass filters (100, 500 1500 Hz). It provides -45dB out of band reduction with one-click operation. There is a headphone jack for private listening. The black metal enclosure features an adjustable stand and wired cable for audio input (mono mini plug) and for 12 VDC 110-500mA input Dim: 3"h x 5"w x 2.5"d; 11 oz............ $129.99 DSP NOISE REDUCTION In-Line DSP Module Noise Eliminating Speaker ADSP 2 Speaker We accept I.M.P.A.C. Government Credit Cards

[close]