2012 / 2013 Aircraft Spruce by Aircraft Spruce and Specialty Co.

More catalogs by Aircraft Spruce and Specialty Co. | 2012 / 2013 Aircraft Spruce | 929 pages | 2013-02-11

Ads

Page 91 of 2012 / 2013 Aircraft Spruce

camloc fasteners the 2600 and 2700 series camloc fasteners exceed requirements for mil-f-5591 style 3 size 2 shear and tensile strength 300 lbs ultimate 200 lbs rated studs and washers listed are made of steel the receptacles are made of copper base alloy all components listed are rated to 450° f the 4002 series fasteners are considerably stronger than the 2600 and 2700 series shear and tensile strength 1050 lbs ultimate 700 lbs rated all studs and grommets listed are made of steel rated to 450° f total material thickness g consists of the thickness of all materials to be fastened this must include the thickness of the material p to which the stud assembly is attached the material f to which the receptacle is attached plus gaskets if used and allowance for paint or other protective finishes if the total thickness is near the upper limit of the stud grip range the next longer stud should be used this will still maintain positive locking of the fastener under vibration p panel thickness .062 f frame thickness .062 grip total thickness .124 p+f g 2600 2700 stud length selection cm wp me ha ap lg ep cs in el av to ps bv stud selection table using 212-12 receptacle total grip use use thickness 2600 2700 .020 .060 .090 .120 .150 .180 .210 .240 .270 .300 .330 .360 .390 .420 .059 .089 .119 .149 .179 .209 .239 .269 .299 .329 .359 .389 .419 .449 2600-1 2600-2 2600-3 2600-4 2600-5 2600-6 2600-7 2600-8 2600-9 2600-10 2600-11 2600-12 2600-13 2600-14 2700-1 2700-2 2700-3 2700-4 2700-5 2700-6 2700-7 2700-8 2700-9 2700-10 2700-11 2700-12 2700-13 2700-14 2600 2700 2600 wing 4002 wing 2600 studs cad plated stainless dash no 2600 slot 26s8 phillips dash 2600 slot price ea price ea no price ea -1 $3.60 $2.60 -1s $4.20 -2 $3.40 $2.35 -2s $4.15 -3 $3.05 $2.45 -3s $4.15 -4 $1.98 $2.35 -4s $3.80 -5 $2.20 $1.70 -5s $3.90 -6 $3.89 $2.35 -6s $4.15 -7 $3.50 $2.85 -7s $3.80 -8 $3.10 $3.70 -8s $4.25 -9 $2.65 $3.95 -9s $3.45 -10 $3.75 $2.20 -10s $4.10 -11 $4.20 12 $3.90 13 $3.40 14 $4.20 $3.90 cad plated wing price cad plated each 2600-2w $7.70 2600-3w $4.75 2600-4w $6.25 2600-5w $6.30 2600-6w $7.75 2600-7w $5.35 2600-8w $11.75 2600-9w $8.11 2600-10w $5.75 2600-11w $7.90 2600-12w $6.75 2600-14w $7.75 stainless 2700 slot price ea -1s $3.80 -2s $3.95 -3s $3.55 -4s $3.15 -5s $3.70 -6s $3.90 -7s $3.95 -8s $4.10 -9s $4.95 -10s $4.15 4002 series large head stud selection to select the proper length stud first select the grommet for example 4002-g next select the receptacle such as 214-16 after determining the total grip thickness use the grommet column under which the selected grommet and receptacle appear use the dash number which appears opposite the determined total grip thickness example if the total determined grip thickness g was 144 the stud dash number for the above 4002-g grommet and 214-16 receptacle would be -4 the stud part number would be 4002-4 stud dash number total grip thickness 4002-g grommet 4002-n 4002-0 grommet range g 214-16 receptacle 214-16 receptacle .021 .050 -1 .055 .080 -2 .081 .110 -2 -3 .111 .140 -3 -4 .141 .170 -4 -5 .171 .200 -5 -6 .201 .230 -6 -7 .231 .260 -7 -8 .261 .290 -8 -9 .291 .320 -9 -10 .321 .350 -10 -11 .351 .380 -11 -12 .381 .410 -12 -13 .411 .440 -13 -14 .441 .470 -14 -15 .471 .500 -15 -16 .501 .530 -16 -17 .531 .560 -17 4002-g grommet requires .090 minimum grip retaining washers are required for studs of -5 length or greater use split washer 2600-sw2 where it is desirable to have the stud fall away for minimum internal projection use internal tooth washer 2600-lw where it is desirable to retain the stud assembly rigidly p/n 2600-sw-2 $0.52 p/n 2600-lw $0.23 2700 studs dash no -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -13 -14 cad plated 2700 slot 27s3 phillips price ea price ea $3.90 $2.98 $3.40 $4.05 $2.98 $3.35 $3.70 $3.25 $3.05 $2.60 $3.75 $3.10 $3.75 $3.40 $3.60 $4.10 $3.95 $2.95 $2.95 $2.65 $2.55 4.45 4.15 $4.10 dash no 4002 studs cad plated stainless dash 4002 cad 40s5 cad plated no plated slot phillips price ea price ea ss phillips 40s5 4002 ss price dash slot each no price ea wing cad plated price each -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 $5.25 $3.45 $3.25 $3.05 $3.25 $3.70 $3.75 $3.70 $3.70 $3.95 $3.95 $3.70 $3.60 $3.97 $4.45 $4.60 $3.40 $3.50 $2.95 $3.15 $3.50 $3.50 $3.50 $3.70 40s5-2s $3.60 40s5-3s $3.97 40s5-4s $3.80 40s5-5s $4.45 40s5-6s $4.20 40s5-7s $4.25 40s5-8s $5.25 40s5-9s $5.25 40s5-10s $5.25 -2s -3s -4s -5s -6s -7s -8s -9s $3.80 $3.85 $3.80 $3.40 $3.98 $3.95 $3.97 $4.00 4002-2w 4002-3w 4002-4w 4002-5w 4002-6w 4002-8w 4002-9w 4002-10w 4002-11w 4002-12w $9.50 $7.75 $7.75 $6.95 $7.25 7.90 $10.00 $8.25 7.95 2600 2700 series retaining washers 4002 series grommets snap rings description part no price ea cad plated flush grommet 4002-g $1.18 flush grommet 4002-h $2.20 plus-flush grommet 4002-n $1.60 stud retaining grommet 4002-o $1.35 high shear flush grommet 40g1-5 $3.30 wide area grommet 4002-n3 $2.20 grommet retaining ring r4g $0.27 high shear grommet r4t $0.77 retaining ring camloc retaining ring 4002-sw $0.65 stainless flush grommet 4002-gs $1.63 flush grommet 4002-hs $1.71 plus flush grommet 4002-ns $1.64 flush grommet 4002-os $1.63 2600 series small enough to fit in limited mounting space and light weight all of these fasteners have a 600 ultimate tensile load capacity 4200 series the modern standard in quick release fastening systems they have an 800 working strength and 1050 ultimate tensile load capacity rivet 2600 2700 series price 4002 series price holes part no each part no each plain 212-12n $2.50 214-16n $3.35 cntersunk 212-12nd $3.10 214-16nd $4.35 plain floating bronze 244-16 $4.10 receptacles aircraft spruce west prices subject to change without notice aircraft spruce east peachtree city ga · 877 477-7823 corona ca · 877 4-spruce 91