Page 21 of High Performance Cams & Gears Catalog by Andrews High Performance Cams & Gears

21 Duration Valve Lift @ Part# Grind Timing(*) .053 .020 Lift TDC Springs Application Comments Duration Valve Lift @ Part# Grind Timing(*) .053 .020 Lift TDC Springs Application Comments Duration Valve Lift @ Part# Grind Timing(*) .053 .020 Lift TDC Springs Application Comments 291581 EV81 32/60 272 306 .610 .262 HI-LIFT For 80-88 inches, 10.5+ C.R., head work. Broad 66/30 276 310 .610 .244 160 LBS. nose, quick ramps for wide torque band. 6500+RPM. 291584 EV84 32/64 276 310 .640 .269 HI-LIFT Quick ramps, broad nose type design means more 70/30 280 314 .640 .246 160 LBS. power for 90-100 inch motors. 6500+ RPM. 291588 EV88 34/70 284 318 .680 .288 HI-LIFT Same as above but more stuff for 100+ inch motors. 76/32 288 322 .680 .264 160 LBS. Expert installation knowledge required. 6500+RPM. 212823 ('70) S82 32/60 272 306 .590 .237 HI-LIFT 74-84 inch Shovels with 10.5+ C.R. New design 212825 ('78) 66/30 276 310 .590 .220 160 LBS. technique for wide, strong power band. 6500+RPM. 212834 ('70) S84 32/64 276 310 .630 .241 HI-LIFT Shovels: 84-96 inches, 10.5+ pistons and head flow 212836 ('78) 70/30 280 314 .630 .223 160 LBS. work for max HP in these larger engines. 6500+RPM. 212855 ('70) S86 34/70 284 318 .660 .254 HI-LIFT 100+ inch Shovels will benefit most from this quick 212857 ('78) 76/32 288 322 .660 .235 160 LBS. ramp design. Broad power band to 6500+RPM. 298880 ('86) V80 32/60 272 306 .600 .264 HI-LIFT .600 lift for Sportsters with 10.5+ C.R. and head flow 298885 ('91) N80 66/30 276 310 .600 .244 160 LBS. work will pull strong to 6500+ RPM. 61-77 inches. 298830 ('86) V83 32/64 276 310 .630 .267 HI-LIFT For 80 to 96 inch motors with head work and 10.5+ 298835 ('91) N83 70/30 280 314 .630 .248 160 LBS. compression. Quick ramps for 6500+RPM. 298870 ('86) V87 34/70 284 318 .670 .283 HI-LIFT Still more stuff for 100+ cubic inches. Quick ramp, 298875 ('91) N87 76/32 288 322 .670 .269 160 LBS. broad tip design will pull strong to 6500+RPM. For big engines (96+ cubic inches) or highly modified smaller motors and running compression ratios of 10.5 or higher, Andrews Products has high lift cams available which will put more usable power at the rear wheel than anything else going. These grinds are specially designed for highly modified motors. EVOLUTION 80 CAMS (Rocker ratio 1.63) (*) Timing .053 cam lift EVOLUTION SPORTSTER CAMS (Rocker ratio 1.63) (*) Timing .053 cam lift SHOVELHEAD CAMS (Rocker ratio 1.43) (*) Timing .053 cam lift Installation requires expert knowledge and machining capability! CAMS FOR DRAGS AND HIGH PERFORMANCE www.andrewsproducts.com 431 Kingston Court Mount Prospect, IL 60056 Phone: 847-759-0190 Fax: 847-759-0848

[close]