Selected page of Conveyor Efficiency Specialists Prodcut Guide
5
Page No.
Miscellaneous Accessories
Simplicity Access Doors . . . . . . . . . . . . . . . . . . . . . . . . . .70-71
Simplicity Chute Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . .68-69
Sealing Systems
At-Last-A-Seal Sealing System . . . . . . . . . . . . . . . . . .60-61
Flexiskirt Sealing System . . . . . . . . . . . . . . . . . . . . . . . .58-59
Gordon Dust Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62-63
Simplicity Slider System . . . . . . . . . . . . . . . . . . . . . . . . .64-65
Worksheets
Dust Shark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Fogger System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Training Idler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Slider Bed Request for Quote . . . . . . . . . . . . . . . . . . . . . .91
Slider Bed . . . . . . . . . . . . . . . . . . . . . . . . . .
| 52
Fogger Systems
Spray Heads
The cluster spray heads are equipped with the
standard #3 nozzle. The quantity of nozzles
supplied, depends upon the spray head required.
Part Numbers:
FS-MK2 7 Nozzles
FS-MK3 13 Nozzles
FS-MK4 9 Nozzles
To add a filter and ball valve to the spray bar,
add -S to the part number shown above.
Pumps
The pumps offered by Arch are equipped with one
filter, one ball valve, a pressure regulation valve, and
pressure gauge. The motors are available in
120/240 or 230/460 voltage.
Part Numbers:
FS-AP75HP1PH 3/4 HP 120/240 volts
FS-AP75HP3PH 3/4 HP 230/460 volts
FS-AP1HP1PH 1 HP 120/240 volts
FS-AP1HP3PH
1 HP 230/460 volts
FS-AP2HP1PH 2 HP 120/240 volts
FS-AP2HP3PH 2 HP 230/460 volts
FS-AP3HP1PH 3 HP 120/240 volts
FS-AP3HP3PH
3 HP 230/460 volts
Additional Notes Water usage per nozzle
Water Pressure:
size: @150 psi
Minimum: 90 psi #1 1.9 gph
Maximum: 150 psi #1.5 2.9 gph
#3 5.7 gph
#6 11.5 gph
#12 23 gph
#18 34.5 gph
Mark 2 Spr
| 57
Easy To Install
The following options for the Wyatt Alignment Disks are available:
Add the selected option to the part number
-WH: White Disk
-SS: Stainless Fasteners
C
Note: With options, prices will vary.
IDLER
WYATT ALIGNMENT DISKS
O.D.
DIMENSIONS IN INCHES (METRIC)
A
B
C
PART NUMBER
4
4 (101.6)
9 (228.6)
1 11/16 (42.9)
DK-4-9
4
4 (101.6)
12 (304.8)
1 11/16 (42.9)
DK-4-12
5
5 (127)
9 (228.6)
1 11/16 (42.9)
DK-5-9
5
5 (127)
12 (304.8)
1 11/16 (42.9)
DK-5-12
6
6 (152.4)
9 (228.6)
1 9/16 (39.7)
DK-6-9
6
6 (152.4)
12 (304.8)
1 9/16 (39.7)
DK-6-12
| 62
M
ost conventional skirting systems do not
seal properly because they wear faster than
you can adjust them. The Gordon Dust Seal is used in
conjunction with the customers existing skirt rubber
to form a secondary sealing area. Manufactured from
Features of the
Gordon Dust Seal
Lightweight.
Easy to install.
No adjustments.
wear resistant EPDM rubber, the dust seal is
available in continuous lengths. Simply tie the rope
provided at each end, and the dust seal is ready for
action.
Gordon Dust Seal
Covered under one or more of the following patents:
4,202,437, 4,231,471, 4,436,446, 4,489,823, 4,533,036, 4,779,716, 4,877,125, 4,989,727, 5,149,305, 5,222,588, 5,222,589, 5,219,063, 5,350,053, 5,725,083, other patents pending.
| 67
Low Maintenance
D
SIDE VIEW OF
IMPACT STAND
ONLY
H
G
WIDE FLANGE I-BEAM
A
B
E
Systems are built to application requirements.
Arch requires the dimensions above to build a system.
BAR SPECIFICATIONS
UHMW COVER
4" [101.6]
SHOCK ABSORBING
RUBBER CORE
STEEL SUBFRAME
COMPLETE IMPACT SYSTEM PART NUMBERS
ORDERING INFORMATION
SIS
**
-
*
-
*
-
*
SYSTEM
BELT
BARS ON
CAPACITY
WIDTH
SYSTEM
TROUGH
LENGTH
2 LIGHT DUTY
24
24 6
20
48 4 FT.
3 MEDIUM DUTY
30
30 6
35
60 5 FT.
4 HEAVY DUTY
36
36 9
45
72 6 FT.
42
42 9
48
48 9
54
54 12
60
60 12
66
66 15
72
72 15
84
84 18
96
96 20
(Example: SIS472-15-45-72)
| 72
R
agged belts and multiple mechanical splices
can destroy conventional belt cleaners.
Because its not always possible for you to keep your
belts in the kind of condition needed for most belt
cleaners to survive, the Gordon Super Saber was
engineered to be the toughest cleaner on the market.
The Super Saber uses the time proven Saber Blade
design, just on a bigger scale. The massive blades,
Features of the
Gordon Super Saber Massive polyurethane blade segments.
Shock absorbing mount.
Interlocking mainframe and support tubes.
Multiple setscrew locking collars.
Twister Tensioner guaranteed for life.
Will not damage mechanical splices.
constructed of wear, cut, and impact resistant
polyurethane, can take the hard pounding of rough
mechanical splices and bad top covers. Mounted to
a heavy-duty frame that is coupled to a dual Gordon
Twister Tensioning System, the Super Saber applies
constant pressure needed to remove the carryback
and keeps working where all o
| 77
Note: With options, prices will vary.
Note: This cleaner consists of a non-segmented blade mounted on a square frame.
High Performance-Low Maintenance
A
6
BELT WIDTH 23" (MAX)
SEE NOTE BELOW
12"
4 1/2" O.D.
10 1/2"
2 1/2" X 2 1/2" X 1/4" SQR. TUBE
1 7/8" O.D. (1 1/2" SCH. 80) PIPE
4 1/2" O.D.
The following options for the Gordon Saber Channel Mount SCM Cleaner are available:
Enter the selected option in place of *
DP: Dual Primary GZ: Grease Fitting W: White Blade
SS: Stainless Pipes C: Ceramic Blade F: Full Blade
H: Heavy Pipes (Sch. 160 Pipe) XHT: High Temperature Blade GB: Grey Blade
FG: Food Grade Blade DT: Dual Tensioner (standard on 84 and above)
BELT
GORDON SABER SCM CLEANER
WIDTH
DIMENSIONS IN INCHES (METRIC)
A
PART NUMBER
18
16 (406.4)
SCM-18-TA-*
24
22 (558.8)
SCM-24-TA-*
30
28 (711.2)
SCM-30-TA-*
36
34 (863.6)
SCM-36-TA-*
42
40 (1016)
SCM-42-TA-*
48
46 (1168.4)
SCM-48-TA-*
54
52 (1320.8)
SCM-54-TA-*
60
58 (1473.2)
SCM-60-
| Arch/BMS Secondary Metal-Bladed Cleaner
T
he Arch /BMS Secondary Metal-Bladed Cleaner
is designed and manufactured with a sturdy and
robust construction that is able to perform effectively in
the most demanding of operating environments. The
torsion holder assembly of this cleaner assures a clean
belt surface on the return side and cuts down on costly
material waste, clean-up costs, and down time. The
Arch/BMS Cleaners are suitable for use in all areas of
carryback spillage and embody the highest quality
components. Since the Arch/BMS design requires low
blade pressure on the belt surface, the life of the blade
is considerably prolonged. A variety of blade types are
available to suit customer requirements, and
polyethylene deflector skirts are standard. The holder
torsion assembly provides stability to the blade to
allow for continuous scraping contact as the blade
tracks the moving belt. The Arch/BMS standard and
heavy-duty cleaner torsion mounts provide constant
p
| 87
The following options for the Gordon V-Plow are available:
Enter the selected option in place of *
Easy To Install
LP: Low Profile
XHT:
High Temperature Blade
GZ: Grease Fitting
W:
White Urethane Blade
H: Heavy Pipes (Sch. 160)
UR:
Urethane Blade
SS: Stainless Pipes
A
O.D. 4 1/2"
C
O.D. 1 2/8" (1 1/2" SCH. 80) PIPE
12"
6"
BELT TRAVEL
9 3/8"
Note: For drawings and dimensions on Angle Plow, contact the factory.
Note: With options, prices will vary.
Note: Some options are not available on all V-Plows.
Note: Standard blade material is 60 durometer rubber.
BELT
GORDON V-PLOW
WIDTH
DIMENSIONS IN INCHES (METRIC)
A
B
C
PART NUMBER
18
18 (457.2) 9 31/32 (253.2)
62 (1574.8)
VP-18-TA-*
24
24 (609.6) 12 31/32 (329.4)
62 (1574.8)
VP-24-TA-*
30
30 (762) 15 23/32 (399.3)
68 (1727.2)
VP-30-TA-*
36
36 (914.4) 18 31/32 (481.8)
74 (1879.6)
VP-36-TA-*
42
42 (1066.8) 21 3/4 (552.4)
80 (2032)
VP-42-TA-*
48
48 (1219.2) 25 (635)
86 (2184.4)
VP-48-T
| 92
Slider Bed Worksheet
Please fill out a photocopy and fax to Arch Environmental Equipment at 800-230-9462.
This worksheet is required before orders can be processed to insure proper installation.
Existing Idler Roll Dimensions
Company:
Date:
Address:
City:
State:
Zip:
Phone:
Fax:
Contact:
Project:
J
C
B
If your shaft is different from the ones shown, please
make a dimensional sketch and include it with this worksheet
L
D
H
Please fill in the dimension that
best reflects the style of your roll.
A.
G.
B.
H.
C.
J.
D.
K.
E.
L.
F.
M.
Idler Manufacturer:
Model Number:
Belt Width:
Belt Speed:
If your shaft is different from the ones shown, please make a
dimensional sketch and include it with this worksheet.
| M I S S I O N S T A T E M E N T
To respond to our customers worldwide
and to satisfy their needs through
quality products and dedicated service.
V I S I O N S T A T E M E N T
To develop a company that will be
responsive to the needs of the customer,
employees, and the community and to
treat all of these with integrity and respect;
to produce a product of the highest
quality and superior workmanship.
Simply The Best
800-553-4567
270-898-6821
FAX 800-230-9462
FAX 270-898-8061
P.O. Box 1760 5929 Benton Road Paducah, KY 42002-1760
http://www.aeec.com
2000 Arch Environmental Equipment, Inc. 8/2000
|
|
