Chevy & GMC Truck Body Components 2015 by Classic Industries

More catalogs by Classic Industries | Chevy & GMC Truck Body Components 2015 | 100 pages | 2015-05-27

Ads

Page 88 of Chevy & GMC Truck Body Components 2015

custom sheet metal t71037 1947-55 custom radiator core support t71034 1947-59 custom front floor set pdl5165 power door lock conversion sets this combination power door lock and keyless entry system will convert your old manual locks to power and activate them from up to 100 feet away power door lock sets include two 4-button keyless remotes two 15 lbs actuators for the door locks wire harness mounting hardware and trunk lock actuator and alarm where applicable power door lock conversion set pdl5120 144.99 set power door lock and trunk conversion set pdl5170 169.99 set power door lock and trunk set with alarm pdl5165 179.99 set the 1947-59 chevrolet/gmc custom front floor set is heavier than stock 16 gauge cold rolled steel and has an 18 gauge transmission tunnel that will clear the typical modern automatic transmission each set comes with the bracing and floor brackets needed to make your floor stronger and better than new important designed to fit custom firewalls only note shipped double oversize no further os2 discounts apply t71034 t71039 1947-55 1st series 289.99 set 1955-59 2nd series 324.99 set these custom radiator core supports fit only the 1947-55 chevrolet 1st series pickup trucks it mounts the sheet metal out on each frame rail and that gives you plenty of up and down and side-to-side fender adjustment the posi-align core support also allows you to mount your radiator approximately 2 ¼ inches lower than stock which in turn lets you use an engine mounted fan this is a bolt-in set with no welding required and includes all the hardware and complete set of instructions needed to install it once installed you will have a core support that not only allows you to run an engine driven fan but also has side-to-side and up and down adjustment for positive alignment of your truck s front sheet metal as for the big ugly rods that held the stock stuff together forget them you no longer need that support these core supports are strong enough to hold everything in place without those rods when you finish you will have a clean and professional look under your hood important does not fit gmc models note shipped oversize no further discounts apply t71037 t71038 os1 1947-53 399.99 set 1954-55 1st series 339.99 set 1947-55 custom firewall with 3” setback sdh100 manufactured from 16 gauge cold rolled steel all the set-back bends and corners on this custom firewall are rounded and smooth includes hardware and instruction booklet this firewall has a frontal opening of 41 with a 3 set-back for a small block or big block engine a firewall pad with is available to keep unwanted heat and noise out of the cab note shipped double oversize no further discounts apply t71042 as733 os2 1947-55 complete firewall 354.99 ea 1947-55 firewall pad 217.99 ea t71035 1947-1955 chevrolet fender skirt set sdh103 these shaved door handle sets will give your vehicle the ultimate smooth look includes two high powered 45 lbs solenoids operated by a keyless remote relay pack door jammers and mounting hardware choose from shaved door handle sets with or without emergency entry or sets that include an alarm or shaved trunk lock important door handle and trunk lock block off plates not included shaved door handle sets sdh100 w/o emergency entry 201.99 set sdh101 w/emergency entry 261.99 set shaved door handle set with alarm sdh102 w/alarm 261.99 set shaved door handle and trunk lock set with alarm sdh103 w/alarm 285.99 set www.classicindustries.com 1955-59 custom firewall with 4 setback the 1955-59 2nd series chevrolet and gmc pickup truck custom firewall is designed with no sharp bends or corners this 16 gauge cold rolled steel firewall includes hardware and instruction booklet this firewall has a 4 set-back to provide more than enough room for a small block or big block engine note shipped double oversize no further discounts apply t71040 t71041 os2 1955-57 2nd series 439.99 set 1958-59 439.99 set important does not fit gmc models note shipped oversize no further discounts apply t71035 t71036 os1 1947-53 389.99 set 1954-55 1st series 389.99 set custom sheet metal 291 body components h shaved door handle sets these are redesigned 1947-55 chevrolet 1st series pickup inner fender aprons the parts in this set are 18 gauge cold rolled steel and each apron features a row of louvers to allow your engine heat to escape into the wheel well when you install this set in conjunction with the custom firewall and the posialign core supports your engine compartment will take on a whole new appearance remember those ugly long radiator support rods that reach from your stock firewall to your core support when you install the inner fender apron set along with the core support set those stock support rods are no longer required this inner fender apron set includes the hardware and complete instructions needed to install it in your truck this is a bolt-in set with no welding required this set will match up against your stock firewall and stock radiator core support with a small amount of trimming to the back edges and some minor adjustments to the front edge.