Catalog: Concrete Fasteners Catalog
Company/Brand: Concrete Fastening Systems
1 25 hole in Concrete Fasteners Catalog by Concrete Fastening Systems
Shear (LB) Tension (LB) Shear (LB) 1/4 5-10 1-1/8 1-3/4 2-3/4 1170 1841 ... 1975 1443 1443 1443 1771 2408 2748 1813 1813 1813 2773 ... 2773 2830 2635 2635 2635 3/8 25-30 1-1/2 3 5 1631 3229 4075 4318 4318 ... 4448 5975 6360 6232 6232 6232 1/2 50-60 2-1/4 4 6 3999 6336 6902 ... 7419 7419 7419 6714 8942 10175 9377 9377 9377 9616 10192 12064 ... 8854 9381 8264 8264 8264 8747 15590 16710 12928 12928 12928 9760 ... 19802 17732 16373 16373 16373 3/4 150-175 3-1/4 6 8 6638 10084 11170 12504 ... 12504 12504 11314 18408 19805 17050 17050 17050 16230 21092 22522 ...
, block and brick. Installation: (1) Drill hole through mounting holes in ... a carbide bit conforming to ANSI B94, 12-77 with the same size bit as anchor ... diameter. (2) Clean hole with wire brush. (3) Make sure nut is ... Insert anchor assembly through mounting holes in fixture and into the base material. ... . The Sleeve anchor requires no maximum hole depth. The depth of the hole in the ... may not be able to be cleaned out of hole. Anchor Spacing: The forces on a Sleeve ... established a minimum standard of ten (10) anchor diameters for spacing between ... should be increased. SIZE BOLT DIA. HOLE SIZE HEAD STYLE MIN. EMBED PULL-OUT ... not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ... satisfactory anchor performance is 4-1/2 bolt diameters. Deeper embedments ...
not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ... satisfactory anchor performance is 4-1/2 bolt diameters. Deeper embedments ... and shear capacity. TECHNICAL DATA 1/4" 1" 3/8" 7/16" 1/4" 2300 lb. 3/ ... 8" 1-9/16" 1/2" 5/8" 3/8" 4100 lb. 1/2" 2" 5/8" 1-3/16" 1/2" 6000 lb. ... 5/8" 2-1/2" 7/8" 1-3/16" 5/8" 8300 lb. 3/4" 3-3/16" 1" 1-3 ... /16" 3/4" 13600 lb. TECHNICAL INFO Approvals: Listed ... Specification FF-S-325 Group Vlll, type 1. Applications: Medium duty into concrete ... . Installation: (1) Drill hole into concrete with a carbide tipped ... drill bit conforming to ANSI B94, 12-77, matching the bit size with the outside ... drop-in anchor being used. Make sure hole depth exceeds minimum embedment. (2) ...
contained unit. All units are made of 100% rust proof material. TECHNICAL INFO ... FF-S-325, Group II, Type 2, Class 1. Applications: Light to medium duty ... , block and brick. Installation: (1) Drill hole of recommended diameter ( ... end of the conical nut first, into the hole The anchor should be flush or slightly ... surface of the base material. A deeper hole should be used when making attachments ... established a minimum standard of ten (10) anchor diameters for spacing between ... increased. ANCHOR SIZE ANCHOR LENGTH HOLE SIZE PULL-OUT 6000 PSI CONCRETE ... not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ... satisfactory anchor performance is 4-1/2 bolt diameters. Deeper embedments ... and shear capacity. TECHNICAL DATA #10 5/8" 3/8" 1180 lb. 5/16" 1" 5/8" ...
. Specification F-S-325, Group IV, Type 1. Applications: Light duty into concrete ... , block and brick. Installation: (1) Drill hole into the base material (see ... chart below for recommended hole size) to a depth equal to the anchor ... length, plus one-quarter inch (1/4") or more. (2) Clean out hole of all ... and cuttings. (3) Place anchor into hole and with light hammer blows, tap anchor ... to be fastened plus anchor length plus 1/4" for complete expansion of anchor ... established a minimum standard of ten (10) anchor diameters for spacing between ... should be increased. ANCHOR SIZE HOLE SIZE SCREW SIZE PULL-OUT 3000 PSI ... not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ... satisfactory anchor performance is 4-1/2 bolt diameters. Deeper embedments ...
, block and brick. Installation: (1) Drill hole of recommended diameter, ... of the expansion shield. Clean out the hole of all dust and cuttings. (2) Place the ... anchor, nut end first, into the hole. The top end of the anchor should be ... established a minimum standard of ten (10) anchor diameters for spacing between ... length. ANCHOR SIZE ANCHOR LENGTH HOLE SIZE BOLT DIA. PULL-OUT 6000 PSI ... not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ... satisfactory anchor performance is 4-1/2 bolt diameters. Deeper embedments ... and shear capacity. TECHNICAL DATA 1/4" 1-5/16" 1/2" 1/4" 800 lb. 3/8 ... " 2" 3/4" 3/8" 1450 lb. 5/8" 3-5/8" 1" 5/8" 2400 lb. ... 5/16" 2" 3/4" 5/16" 1100 lb. 1/2" 2-1/2" 7/8" 1/2" 1850 lb. 3/4" ...
, block and brick. Installation: (1) Drill hole of recommended diameter, ... of the expansion anchor. Clean out the hole of all dust and cuttings. (2) Place the ... anchor, nut end first, into the hole. The top end of the anchor should be ... established a minimum standard of ten (10) anchor diameters for spacing between ... length. ANCHOR SIZE ANCHOR LENGTH HOLE SIZE BOLT DIA. PULL-OUT 5000 PSI ... not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ... satisfactory anchor performance is 4-1/2 bolt diameters. Deeper embedments ... and shear capacity. TECHNICAL DATA 1/4" 1-3/8" 1/2" 1/4" 1100 lb. 3/8" ... 2-1/16" 3/4" 3/8" 1750 lb. 5/8" 3" 1" 5/8" 6500 lb. 5/16" 1-3/4" 3/4" 5 ... /16" 1450 lb. 1/2" 2-1/2" 7/8" 1/2" 2200 lb. 3/4" 4" 1-1/4" 3/4" ...
Specification FF-S-325, Group II, Type 1, Class 1 2. Zamak #5 Zinc Alloy meets ... , block and brick. Installation: (1) Drill hole of recommended diameter, ... expansion anchor plus one half inch (1/2") or more. (2) Clean the hole of all ... anchor, ribbed end first, into hole. Tap with a hammer until flush with the ... shield should be driven deeper into the hole by hand hammering the head of the lag ... be fastened plus Lag Shield length plus 1/2" equals Lag Screw length. Anchor ... established a minimum standard of ten (10) anchor diameters for spacing between ... should be increased. ANCHOR SIZE HOLE SIZE ANCHOR LENGTH PULL-OUT 6000 PSI ... CONCRETE TECHNICAL DATA 1/4" Short 1/2" 1" 400 lb. 5/16" Short 1/2" 1-1 ... /4" 800 lb. 3/8" Short 5/8" 1-3/4" 1300 lb. 1/2" Short 3/4" 2" 2100 lb. 5/ ...
10 p 888.498.5747 f 216.391.5352 www. ... screw cuts threads in a predrilled hole in concrete, brick or block. The screw ... concrete screw is available in both 3/16" or 1/4" diameters with either a flat ... phillips #3 countersunk or a 5/16" hex washer head. All screws are plated ... , brick and block. Installation: (1) Drill hole into base material using ... with the screws. The depth of the hole must be at least 1/4" deeper than the ... . (2) Place object to be fastened over hole. (3) Insert point of Tapcon into hole ... . It is recommended that a minimum of 1" and a maximum of 1-3/4" embedment be ... box of TapCon fasteners. The correct hole must be drilled for the screw to obtain ... holding values. In all cases the hole must be at least 1/4" deeper than the ...
11 p 888.498.5747 f 216.391.5352 www. ... , block and brick. Installation: (1) Drill hole in base material using a ... the Nylon Nail-it being used. Make sure hole is 1/4" deeper than expected embedment ... . (2) Clean out the hole of all dust and cuttings. (3) Push ... rule of thumb, anchors should be spaced 18 to 24 inches from center to center to ... are not guaranteed A safety factor of 4:1 or 25% is generally accepted as a safe ... satisfactory anchor performance is 4-1/2 bolt diameters. Deeper embedments ... and shear capacity. TECHNICAL DATA 3/16" x 3/4" 3/16" 1/2" 200 lb. 3/16" x 1 ... " 3/16 1/2" 225 lb. 3/16" x 1-1/2" 3/16 1/2" 265 lb. 1/4" x 1" 1/4 ... " 1/2" 210 lb. 1/4" x 1-1/2" 1/4" 1/2" 250 lb. 1/4'x 2" 1/4" 1/2" 265 ...
12 p 888.498.5747 f 216.391.5352 www. ... block and brick. Installation: (1) Drill hole in base material equal to ... diameter of anchor being used. Hole depth should be at least 1/4" deeper ... the anchor embedment. (2) Clean out hole of all dust and shavings. (3) Insert ... material to be fastened and into hole. The bottom of the head must be sitting ... be fastened plus minimum embedment plus 1/4" equals anchor length. Anchor ... established a minimum standard of ten (10) anchor diameters for spacing between ... not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ... satisfactory anchor performance is 4-1/2 bolt diameters. Deeper embedments ... and shear capacity. TECHNICAL DATA 3/16" x 7/8" 3/16" 1/2" 500 lb. 1/4" x 1 ...
13 p 888.498.5747 f 216.391.5352 www. ... the base. When driven into the concrete hole, these halves are compressed. Once an ... force upon the inside walls of the hole, resulting in low "slip" rates and ... duty in concrete. Installation: (1) Drill hole in concrete with carbide ... tipped bit meeting ANSI standards. Hole should be drilled minimum embedment or ... deeper, plus 1/4" (2) Clean dust out of hole. (3) Insert anchor through fixture and ... into hole. (4) Hammer anchor into hole flush with the top of fixture. Anchor ... be fastened plus minimum embedment plus 1/4" equals anchor length. Anchor ... established a minimum standard of ten (10) anchor diameters for spacing between ... not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ...
14 p 888.498.5747 f 216.391.5352 www. ... anchor is carbon steel with an interior hole extending the length of the anchor. The ... pin comes inserted in the interior hole of the anchor. The anchor is threaded ... , Meets City of Los Angeles Approval #25109, Meets or exceeds G.S.A. Standards G.S.A ... factors in compliance with A.N.S.I. A58-1, Meets plating standard in compliance ... to heavy into concrete. Installation: (1) Drill hole of sufficient depth using a ... not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ... require a safety factor of as much as 10:1, or more. TECHNICAL DATA 1/4" x 1-3/4" ... 5/8" 1" 1/4" 3-1/2" 1-3/4" 900 lb. 1600 lb. 1/4" x 2-3/8" 3/4" 1" 1/4" 3-1/2 ... " 1-3/4" 900 lb. 1600 lb. 1/4" x 3" 3/4" 1" 1/4" 3-1/2" 1-3/4" ...
16 p 888.498.5747 f 216.391.5352 www. ... allows the fastener to make a small hole that does not disrupt the consistency ... has a single point that drills a clean hole and prevents paper damage. The deep ... . The tapered, oversized head seals the hole with a flush mount. TECHNICAL INFO ... . Do not use overhead. Installation: (1) Insert #2 Phillips bit tip into head ... with the wall. (3) Place fixture over hole and tighten the proper size sheet metal ... screw. A one inch 1" minimum thread engagement is ... of material to be fastened plus 1" penetration into anchor equals screw ... rule of thumb, anchors should be spaced 18 to 24 inches from center to center to ... detectors. SIZE WALL THICKNESS 3/8" 1/2" 5/8" Values shown are average ... not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ...
17 p 888.498.5747 f 216.391.5352 www. ... and composite panels. Installation: (1) Drill appropriate sized hole. Hold ... straps and slide channel through hole. (2) With one hand, pull ring so metal ... . Minimum clearance behind wall is 1-7/8" Screw Length: Thickness of material ... rule of thumb, anchors should be spaced 18 to 24 inches from center to center to ... should be increased. SIZE GRIP RANGE 1 5/8" WALL BOARD CONCRETE BLOCK STEEL ... PLATE (1) Long strap toggler bolts are available ... that cover a range from 2" to 9-1/2" (2) Values shown are average ... in any way. A safety factor of 4:1 or 25% is generally accepted as a safe working ... working ratio. TECHNICAL DATA 3/16"- 24 3/8" to 2-1/2" 356 lbs. 714 lb. ... 918 lb. 1/4" 20 3/8" to 2-1/2" 306 lbs. 925 lb. 1283 lb. 3/8" 16 ...
18 p 888.498.5747 f 216.391.5352 www. ... to the side of the body. The body has a hole through the center and webs on the ... allow them to be inserted in to the hole. As the screw passes through the body, ... paneling. Installation: Hollow Wall (1) Drill 5/16" hole. (2) Fold anchor, ... insert anchor in hole and tap flush with wall. (3) Insert key ... with fixture. Solid Base Material (1) Drill 5/16" hole. (2) Clean out hole ... . (3) Fold anchor, insert anchor in hole and tap flush with base material. (4) ... TA toggler is for material thickness of 1/8" to 1/4". The TB is for material ... thickness of 3/8" to 1/2" and the TC is for material thickness ... rule of thumb, anchors should be spaced 18 to 24 inches from center to center to ... be increased. SIZE PULL-OUT LBS. 1/4" PLYWOOD PULL-OUT LBS. 3/8" DRYWALL ...
