6 results for 2 1 2 drive found in 0.000 seconds

4 p 888.498.5747 f 216.391.5352 www.confast.com DROP-IN A Drop-In ... not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ... satisfactory anchor performance is 4-1/2 bolt diameters. Deeper embedments will ... and shear capacity. TECHNICAL DATA 1/4" 1" 3/8" 7/16" 1/4" 2300 lb. 3/ ... 8" 1-9/16" 1/2" 5/8" 3/8" 4100 lb. 1/2" 2" 5/8" 1-3/16" 1/2" 6000 lb. ... 5/8" 2-1/2" 7/8" 1-3/16" 5/8" 8300 lb. 3/4" 3-3/16" 1" 1-3 ... /16" 3/4" 13600 lb. TECHNICAL INFO Approvals: Listed ... Specification FF-S-325 Group Vlll, type 1. Applications: Medium duty into concrete ... . Installation: (1) Drill hole into concrete with a ... drill bit conforming to ANSI B94, 12-77, matching the bit size with the outside ...

10 p 888.498.5747 f 216.391.5352 www.confast.com TAPCON CONCRETE SCREWS ... concrete screw is available in both 3/16" or 1/4" diameters with either a flat ... phillips #3 countersunk or a 5/16" hex washer head. All screws are plated ... , brick and block. Installation: (1) Drill hole into base material using ... The depth of the hole must be at least 1/4" deeper than the TapCon embedment. (2 ... 3) Insert point of Tapcon into hole and drive screw in using a nut drive or #3 bit ... . It is recommended that a minimum of 1" and a maximum of 1-3/4" embedment be ... In all cases the hole must be at least 1/4" deeper than the depth of the ... failure values. A. safety factor of 4:1. or 25% of ultimate pullout value, is ... . TECHNICAL DATA PULL-OUT VALUES 3/16" 1" 380 lb. 229 lb. 3/16" 1-3/4" 1090 ...

11 p 888.498.5747 f 216.391.5352 www.confast.com NYLON NAIL-IT This ... Specifications FF-S-325, Group V, Type 2, Class 4. Applications: Light duty in ... , block and brick. Installation: (1) Drill hole in base material using a ... Nail-it being used. Make sure hole is 1/4" deeper than expected embedment. (2) ... body is snug up to the fixture. (4) Drive the expander pin home to complete the ... rule of thumb, anchors should be spaced 18 to 24 inches from center to center to ... are not guaranteed A safety factor of 4:1 or 25% is generally accepted as a safe ... satisfactory anchor performance is 4-1/2 bolt diameters. Deeper embedments will ... and shear capacity. TECHNICAL DATA 3/16" x 3/4" 3/16" 1/2" 200 lb. 3/16" x 1 ... " 3/16 1/2" 225 lb. 3/16" x 1-1/2" 3/16 1/2" 265 lb. 1/4" x 1" 1/4" ...

13 p 888.498.5747 f 216.391.5352 www.confast.com SPLIT DRIVE ANCHOR ... Split Drive anchors are a one-piece, all steel ... concrete anchor. Split drive anchors are manufactured with through ... , preexpanded halves at the base. When driven into the concrete hole, these halves ... for poor grade or old concrete. Split Drive Anchor can come with either a flat ... duty in concrete. Installation: (1) Drill hole in concrete with carbide ... minimum embedment or deeper, plus 1/4" (2) Clean dust out of hole. (3) ... be fastened plus minimum embedment plus 1/4" equals anchor length. Anchor ... Spacing: The forces on a Split Drive Anchor are transferred to the material ... established a minimum standard of ten (10) anchor diameters for spacing between ... not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ...

14 p 888.498.5747 f 216.391.5352 www.confast.com STRIKE ANCHOR The ... the length of the anchor. The hardened drive pin comes inserted in the interior hole ... is threaded on the top end where the drive pin is inserted. The other end of the ... , Meets City of Los Angeles Approval #25109, Meets or exceeds G.S.A. Standards G.S.A ... . FF-S-325, Group V, Type 2 Class 2, Meets load factors in compliance with A ... .N.S.I. A58-1, Meets plating standard in compliance ... to heavy into concrete. Installation: (1) Drill hole of sufficient depth using a ... as the anchor being installed. (2) Place washer and nut on anchor, ... SPACE BETWEEN EDGE DISTANCE PULL-OUT 2000 PSI SHEAR 2000 PSI Values shown are ... not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe ...

15 p 888.498.5747 f 216.391.5352 www.confast.com HANGAR MATE HangerMate ... allows fast and reliable attachment of 1/4" or 3/8" threaded rod into concrete, ... and specifications, please call 1-888-498- 5747 for all current code approvals. ... . Installation: For Metal or Wood (1) Insert HangerMate recessed drive ... ) or appropriate cordless screw gun. (2) Insert appropriate HangerMate anchor ... into drive socket. (3) Position the self-drilling ... screw gun operation at approximately 1800 rpm, install the HangerMate anchor. The ... drive socket's safety set feature will set ... or component. For Masonry/Concrete (1) Insert appropriate HangerMate matched ... hammer or rotary hammer drill. For SDS-drive drills use bit ZE380; for keyed chuck- ... type drills use bit ZE360. (2) With the drill in the hammer mode, ...