15 results for 8 in lb found in 0.000 seconds

2 p 888.498.5747 f 216.391.5352 www.confast.com ... SYSTEM TECHNICAL DATA ANCHOR DIAMETER (in.) EMBED. DEPTH (in.) Torque Ft/Lb 2000 ... PSI 4000 PSI 6000 PSI Tension (LB) Shear (LB) Tension (LB) Shear (LB ... ) Tension (LB) Shear (LB) 1/4 5-10 1-1/8 1-3/4 2-3/4 1170 ... 2773 2773 2830 2635 2635 2635 3/8 25-30 1-1/2 3 5 1631 3229 4075 ... 6336 6902 7419 7419 7419 6714 8942 10175 9377 9377 9377 9616 10192 ... 12064 9888 9888 9888 5/8 75-90 3-3/4 5 7 4999 8854 9381 ... 8264 8264 8264 8747 15590 16710 12928 12928 12928 ... 16373 16373 3/4 150-175 3-1/4 6 8 6638 10084 11170 12504 12504 12504 ... 21092 22522 22965 22965 22965 7/8 200-250 3-7/8 5-3/4 8-3/4 8392 ...

3 p 888.498.5747 f 216.391.5352 www.confast.com SLEEVE ... Each part is zinc plated and assembled into a complete ready-to-use anchor. The ... the nut pulls the coneshaped stud end into the expander sleeve, wedging it outward ... and locking the anchor into the base material. TECHNICAL INFO ... by Underwriters Laboratories (UL), International Conference of Building Officials (ICBO ... 3, Class 3. Applications: Medium duty into concrete, block and brick. Installation ... : (1) Drill hole through mounting holes in fixture or directly through material to ... be fastened and into the base material, using a carbide bit ... with the top threaded part of anchor. Insert anchor assembly through mounting holes ... in fixture and into the base material. Push anchor assembly ...

4 p 888.498.5747 f 216.391.5352 www.confast.com DROP-IN ... A Drop-In anchor consists of a zinc plated steel ... that allows either flush or countersunk installation. the bottom lip of the shield is tapered ... working load. Reference should be made in applicable codes for specific working ... capacity. TECHNICAL DATA 1/4" 1" 3/8" 7/16" 1/4" 2300 lb. 3/8" 1-9/16" ... 1/2" 5/8" 3/8" 4100 lb. 1/2" 2" 5/8" 1-3/16" 1/2" 6000 lb. 5/8" 2-1/2" ... 7/8" 1-3/16" 5/8" 8300 lb. 3/4" 3-3/16" 1" 1-3/16" 3/4" ... 13600 lb. TECHNICAL INFO Approvals: Listed by Underwriters ... Laboratories (UL), International Conference of Building Officials (ICBO ... Vlll, type 1. Applications: Medium duty into concrete. Installation: (1) Drill hole ...

5 p 888.498.5747 f 216.391.5352 www.confast.com MACHINE ... alloy sleeve and a zinc alloy (Zamak 5) internally threaded cone with a series of integral ... the cone shaped nut from turning in the sleeve. All size anchors, except ... the 3/4" size, are preassembled into a single, self contained unit. All ... of 100% rust proof material. TECHNICAL INFO Approvals: Meets G.S.A. Specification ... 1. Applications: Light to medium duty into concrete, block and brick. ... Installation: (1) Drill hole of recommended diameter ... (see chart below) into the base material to a depth equal to ... , base end of the conical nut first, into the hole The anchor should be flush or ... the pilot end of the setting tool into the threaded bore of the anchor and ... to be fastened over the anchor and bolt into place. The length of the screw or bolt ...

6 p 888.498.5747 f 216.391.5352 www.confast.com LEADWOOD ... designed to facilitate proper expansion in masonry. The anchor is split from the ... tapers outward from the anchor diameter into a tubular thin section cone. The ... at the outer end of the anchor, in combination with the longitudinal split ... , facilitates ease of initial expansion and prevents the anchor from ... turning in the masonry. As the screw progresses ... deeper into the anchor, the longitudinal ribs bite ... into the masonry, preventing the anchor from ... to form its own threads. TECHNICAL INFO Approvals: Meets G.S.A. Specification F ... IV, Type 1. Applications: Light duty into concrete, block and brick. ... Installation: (1) Drill hole into the base material (see chart below for ...

7 p 888.498.5747 f 216.391.5352 www.confast.com SINGLE ... contains a wedge shaped nut at one end. Integral lugs on the nut and cone keep the ... wedges from turning in the tubular shield during expansion. ... , removed, and/or refastened. TECHNICAL INFO Approvals: Meets Zamak 5 Zinc Alloy: A. ... S.A.E. 925. Applications: Medium duty in concrete, block and brick. ... Installation: (1) Drill hole of recommended diameter ... , see chart below, into the base material to a depth equal to, ... Single Expansion anchor, nut end first, into the hole. The top end of the anchor ... object to be fastened over the anchor in the base material and bolt into place. ... transferred to the material that it is installed in. If the anchors are installed too ...

8 p 888.498.5747 f 216.391.5352 www.confast.com DOUBLE ... hollow cone at the the other end. Integral lugs on the nut and cone keep the ... wedges from turning in the tubular shield during expansion. ... , removed, and/or fastened. TECHNICAL INFO Approvals: Meets Zamak 5 Zinc Alloy: A. ... S.A.E. 925. Applications: Medium duty in concrete, block and brick. ... Installation: (1) Drill hole of recommended diameter ... , see chart below, into the base material to a depth equal to, ... Double Expansion anchor, nut end first, into the hole. The top end of the anchor ... object to be fastened over the anchor in the base material and bolt in to place ... transferred to the material that it is installed in. If the anchors are installed too ... close together, it can cause an interaction of the forces, thus reducing the ...

9 p 888.498.5747 f 216.391.5352 www.confast.com LAG ... -part expansion shield is preassembled into a self-contained single unit. The shell ... -like unit has tapered internal threads for a portion of its length. ... for a portion of its length. Precision internal threads permit easy turning of the lag ... a rust-proof material. The anchor comes in two lengths, short or long. The short ... lag shield is for anchoring in high grade concrete or where thickness ... shield. The long Lag shield is for use in lower grade base material or where ... strength is required. TECHNICAL INFO Approvals: Meets G.S.A. Specification ... . Applications: Light to medium duty into concrete, block and brick. ... Installation: (1) Drill hole of recommended diameter ... , into the base material equal to the length ...

10 p 888.498.5747 f 216.391.5352 www.confast.com TAPCON ... brand concrete screw cuts threads in a predrilled hole in concrete, brick or ... brand concrete screw is available in both 3/16" or 1/4" diameters with ... and additional lubricity for ease of installation. TapCon screws are also available in 410 ... steel screws have shown no red rust in salt spray test performed at a ... per ASTM B117 specifications. TECHNICAL INFO Applications: Light to medium duty in ... concrete, brick and block. Installation: (1) Drill hole into base material using ... object to be fastened over hole. (3) Insert point of Tapcon into hole and drive ... screw in using a nut drive or #3 bit tip. Do not ... with the desired depth of embedment in the base material. It is recommended ...

12 p 888.498.5747 f 216.391.5352 www.confast.com METAL ... runs through the head thickness and into the shank for a depth just beyond the ... point where the slot terminates in the body. The steel pin expander is ... maximum corrosion resistance. TECHNICAL INFO Approvals: Meets G.S.A. specifications ... 3. Applications: Light to medium duty in concrete block and brick. Installation ... : (1) Drill hole in base material equal to diameter of ... out hole of all dust and shavings. (3) Insert Metal Hit Anchor , slit end first ... through material to be fastened and into hole. The bottom of the head must be ... fixture plate. (4) Hammer nail flush into head of anchor body. The Metal Hit ... transferred to the material that it is installed in. If the anchors are installed too ...

13 p 888.498.5747 f 216.391.5352 www.confast.com SPLIT ... halves at the base. When driven into the concrete hole, these halves are ... . This exerts tremendous force upon the inside walls of the hole, resulting in low " ... slip" rates and increased vibration resistance. The positive ... sunk head or a round head. TECHNICAL INFO Approvals: Meets G.S.A. Specification ... VI. Applications: light to medium duty in concrete. Installation: (1) Drill hole ... in concrete with carbide tipped bit ... 1/4" (2) Clean dust out of hole. (3) Insert anchor through fixture and into hole. ( ... 4) Hammer anchor into hole flush with the top of fixture. ... transferred to the material that it is installed in. If the anchors are installed too ... close together, it can cause an interaction of the forces, thus reducing the ...

14 p 888.498.5747 f 216.391.5352 www.confast.com STRIKE ... of the anchor is carbon steel with an interior hole extending the length of the anchor ... . The hardened drive pin comes inserted in the interior hole of the anchor. The ... on the top end where the drive pin is inserted. The other end of the anchor has four ... dicromate over zinc plating. TECHNICAL INFO Approvals: Meets I.C.B.O. standards ... V, Type 2 Class 2, Meets load factors in compliance with A.N.S.I. A58-1, Meets ... plating standard in compliance with A.S.T.M. E488488. ... Applications: Medium to heavy into concrete. Installation: (1) Drill hole ... the same diameter as the anchor being installed. (2) Place washer and nut on anchor, ... . (3) With nut, washer, and set-pin in place, insert anchor through the ...

16 p 888.498.5747 f 216.391.5352 www.confast.com WALL ... DRILLER The Wall Driller is injection molded of engineered plastic or long ... the hole with a flush mount. TECHNICAL INFO Applications: Light duty into wallboard ... . Do not use overhead. Installation: (1) Insert #2 Phillips bit tip into ... head of wall driller. (2) Press point into wallboard, while turning the anchor ... proper size sheet metal screw. A one inch 1" minimum thread engagement is ... to be fastened plus 1" penetration into anchor equals screw length. Anchor ... transferred to the material that it is installed in. If the anchors are installed too ... close together, it can cause an interaction of the forces, thus reducing the ... power of the anchor. When anchoring into low-density materials, the holding ...

17 p 888.498.5747 f 216.391.5352 www.confast.com TOGGLER ... anchoring channel pivoted on durable installation legs. The sliding cap ratchets down the ... a stainless steel channel. TECHNICAL INFO Applications: light to medium duty in ... , fiberglass and composite panels. Installation: (1) Drill appropriate sized hole. Hold ... off straps flush with wall. (4) Insert bolt through item to be fastened and ... . Minimum clearance behind wall is 1-7/8" Screw Length: Thickness of material to ... transferred to the material that it is installed in. If the anchors are installed too ... close together, it can cause an interaction of the forces, thus reducing the ... power of the anchor. When anchoring into low-density materials, the holding ...

18 p 888.498.5747 f 216.391.5352 www.confast.com PLASTIC ... on the sides to resist spinning during installation. The legs collapse to form a tonjue, ... which allow them to be inserted in to the hole. As the screw passes ... through the body, it draws in and expands the legs for double holing ... distributing truss. Anchors can be used in any material (masonite, plywood, ... perform as wedge or solid wall anchors in materials with thicknesses above wall ... range, without modification. TECHNICAL INFO Applications: Light to medium duty in ... , masonite, plywood and paneling. Installation: Hollow Wall (1) Drill 5/16" hole. (2) ... Fold anchor, insert anchor in hole and tap flush with wall. (3) ... Insert key to pop anchor open behind hollow ...