4 results for 8 point bit found in 0.052 seconds

[View Catalog] Catalog: Concrete Fasteners Catalog Company/Brand: Concrete Fastening Systems
	[View page 12] 10 p 888.498.5747 f 216.391.5352 www.confast.com TAPCON ... hole into base material using the drill bit provided with the screws. The depth of ... to be fastened over hole. (3) Insert point of Tapcon into hole and drive screw in ... using a nut drive or #3 bit tip. Do not over torque the screw. ... strengths. A carbidetipped drill bit is supplied with each box of TapCon ... drilled with Elco carbide tipped drill bits. Designated holding power depends on the ... " 1-3/4" 1090 lb. 521 lb. 1/4" 1" 800 lb. 490 lb. 1/4" 1-3/4" 2100 lb. ... 801 lb. SIZE EMBEDMENT CONCRETE 3725 PSI ... HOLLOW BLOCK SHEAR VALUES 3/16" 1-3/8" 875 lb. 690 lb. 1/4" 1-3/4" 1924 ...
	[View page 14] 12 p 888.498.5747 f 216.391.5352 www.confast.com METAL ... the shank for a depth just beyond the point where the slot terminates in the body. ... should be increased. SIZE DRILL BIT MINIMUM EMBEDMENT PULL-OUT Values ... capacity. TECHNICAL DATA 3/16" x 7/8" 3/16" 1/2" 500 lb. 1/4" x 1" 1/4 ...
	[View page 17] 15 p 888.498.5747 f 216.391.5352 www.confast.com HANGAR ... and reliable attachment of 1/4" or 3/8" threaded rod into concrete, steel and ... and specifications, please call 1-888-498- 5747 for all current code approvals. ... socket. (3) Position the self-drilling point of the anchor at the intended point of ... matched tolerance carbide-tipped drill bit into hammer or rotary hammer drill. For ... SDS-drive drills use bit ZE380; for keyed chuck-type drills use ... bit ZE360. (2) With the drill in the hammer ... mode, drill the full length of the bit. (3) Slide drive sleeve ZE220 over drill ... bit, locking its enternal hex recess with ... the hex collar of the drill bit. (4) Insert appropriate HangerMate ... 16 W/NUT 14 GA 14 W/NUT 12 W/NUT 1/8" 3/16" 1/4" 12 GA Is a registered ...
	[View page 18] 16 p 888.498.5747 f 216.391.5352 www.confast.com WALL ... of the drywall. The anchor has a single point that drills a clean hole and prevents ... . Installation: (1) Insert #2 Phillips bit tip into head of wall driller. (2) ... Press point into wallboard, while turning the ... smoke detectors. SIZE WALL THICKNESS 3/8" 1/2" 5/8" Values shown are average ... ratio. TECHNICAL DATA #6 Plastic 3/8" to 5/8" 25 lbs. 40 lb. 85 lb. #8 ... Plastic 3/8" to 5/8" 25 lbs. 40 lb. 85 lb. #8 Zamak 3/8" to 5/8" 25 lbs. ... 40 lb. 85 lb. PULL-OUT TEST IN WALLBOARD ...

Similar searches 8 point bit (249)
8 point screwdriver bit (26)
8 point screwdriver (91)
8 point allen wrench set (18)
8 point torq (7)
8 point socket (252)
8 point torx socket (22)
8 pt bit (59)
8 point torx universal socket (13)
8 point chuck (49)
8 point drive sockets (138)
5 point drill bits (52)
8 mm 12 point (389)
8 mm 12 point wrench (60)
8 cylinder engine points and condenser (21)
apex 4 point phillips bit (14)
8 pin adapter microphone (32)
performance built 4 8 gm engines (80)
ford windstar 1995 3 8 (10)
11 2 hex bit socket (62)
11 2 hex bit (114)
2001 v6 3 8 (90)
3 8 drive x 36mm socket (7)
4 point drive sockets (142)
sfg 8 (56)
gh 46 8 (10)
12 point socket (217)
ratcheting bit driver (66)
tq 8 (31)
screwdriver bit (183)
rg 8 (248)
rg 8 cable (109)
aluminum ford v 8 (143)
hex bits (222)
rec 8 (342)
srt 8 (81)
hi torqü bits 14 (8)
cpi 8 (119)
maya 8 (47)
07 mazda rx 8 (17)
05 mazda rx 8 (16)
t10 bit (30)
three wing bit (19)
bits three wing (19)
bits tri wing (27)
bits 3 wing (41)
four point contact ball bearing (22)
drill bits (300)
ford sho 1995 3 8 (8)
ss 810 1 8 (22)
sb chevy 400 8 harmonic balancer (17)
turbo gm 8 (127)
8 position antenna switch (63)
apex bit (71)
zm 40 8 (23)
zm 40 8 pkz (8)
stanley hex bit (28)
clutch head bits (18)
apex socket head bits (23)
6 square drive bit (77)
8 12 rain cap (35)
4 cylinder v 8 dodge truck (9)
civic 8 (170)
38 drive 4 point sockets (48)
hard wire power points (50)
ford 8 cylinder engines (512)
hollow point (143)
bx 8 (182)
model rec 8 (92)
2005 mazda rx 8 (10)