Catalog: Concrete Fasteners Catalog | |
| DIAMETER (in.) EMBED. DEPTH (in.) Torque Ft/Lb 2000 PSI 4000 PSI 6000 PSI ... HOLE SIZE MINIMUM EMBEDMENT STANDARD THREAD LENGTH EXTRA THREAD LENGTH 1/4 all ... 1-1/2 7/8 3/8 3/8 1-1/2 1-1/8 1/2 all sizes 1/2 2-1/4 1-1/4 *1/2 x 7 1/2 ... 2-1/4 1-1/4 4 5/8 all sizes 5/8 2-3/4 2 *5/8 x 7 5/8 2- ... 4 *5/8 x 8-1/2 5/8 2-3/4 2 5 3/4 all sizes 3/4 3-1/4 2 *3/4 x 7 3/4 3- ... *These anchors come with the standard thread length or with the extra thread length ... working load. Reference should be made to applicable codes for the specific ... | |
| Anchor is made up of an antimonial lead alloy sleeve and a zinc alloy (Zamak 5) ... internally threaded cone with a series of integral ribs or ... shaped nut from turning in the sleeve. All size anchors, except the 3/4" size, are ... into a single, self contained unit. All units are made of 100% rust proof ... , Type 2, Class 1. Applications: Light to medium duty into concrete, block and ... see chart below) into the base material to a depth equal to the length of the ... should be used when making attachments to poor masonry or when additional holding ... ) Position the pilot end of the setting tool into the threaded bore of the anchor ... and press firmly against the lead alloy sleeve of the anchor. Using a hand ... hammer, strike the end of the setting tool with repeated sharp blows. Anchor is ... | |
| screw anchor tapers and is designed to facilitate proper expansion in masonry ... ribs for a portion of its length. The top end of the anchor tapers outward from ... preventing the anchor from twisting and allowing the screw to form its own threads. ... Type 1. Applications: Light duty into concrete, block and brick. Installation: (1) ... chart below for recommended hole size) to a depth equal to the anchor length, ... (1/4") or more. (2) Clean out hole of all dust and cuttings. (3) Place anchor ... . Screw Length: Thickness of material to be fastened plus anchor length plus 1/4 ... a Leadwood screw anchor are transferred to the material that it is installed in. ... If the anchors are installed too close together, it can cause an interaction of the ... SIZE SCREW SIZE PULL-OUT 3000 PSI CONCRETE Values shown are average ultimate ... | |
| . The two piece tubular shield is bound together with one spring band. It contains a ... anchor are of precision die-cast zinc alloy commonly known as Zamak 5. the ... loads or where the bolt is subjected to side pressure or vibration. Once ... INFO Approvals: Meets Zamak 5 Zinc Alloy: A.S.T.M. Specification 24 (AC41A) and S ... A.E. 925. Applications: Medium duty in concrete, block and brick. Installation: (1) ... see chart below, into the base material to a depth equal to, or slightly deeper ... expansion shield. Clean out the hole of all dust and cuttings. (2) Place the Single ... , nut end first, into the hole. The top end of the anchor should be flush or ... material surface. (3) Place the object to be fastened over the anchor in the base ... . The bolt should engage 2/3 of the threads of the anchor. Anchor Spacing: The ... | |
| shell-like unit has tapered internal threads for a portion of its length. The ... of its length. Precision internal threads permit easy turning of the lag screw ... may be easily unbolted and removed. All parts of the completed unit are made of ... zinc alloy commonly known as Zamak 5, a rust-proof ... shield is for anchoring in high grade concrete or where thickness of base material ... II, Type 1, Class 1 2. Zamak #5 Zinc Alloy meets the A.S.T.M. specification XXV ( ... ) and S.A.E. 925. Applications: Light to medium duty into concrete, block and ... diameter, into the base material equal to the length of the expansion anchor plus ... (1/2") or more. (2) Clean the hole of all dust and cuttings. (3) Place the ... material. (4) Position the material to be fastened over the shield in the base ... | |
| f 216.391.5352 www.confast.com TAPCON CONCRETE SCREWS The TapCon brand concrete screw ... cuts threads in a predrilled hole in concrete, brick or block. The screw has ... alternating raised and lowered threads with diamond cut notches which provide ... power and stability. The TapCon brand concrete screw is available in both 3/16" or 1/4 ... countersunk or a 5/16" hex washer head. All screws are plated using the Stalgard ... . TECHNICAL INFO Applications: Light to medium duty in concrete, brick and ... the TapCon embedment. (2) Place object to be fastened over hole. (3) Insert point ... a nut drive or #3 bit tip. Do not over torque the screw. Screw Length: The length of ... the TapCon fastener to be used is determined by combining the ... thickness of the material to be attached with the desired depth of ... | |
| body. The steel pin expander is similar to a nail except for the specially ... designed thread in a section of its shank and the ... resistance. The specially designed threads and head on the expander pin lock the ... , Class 4. Applications: Light duty in concrete, block and brick. Installation: (1) ... embedment. (2) Clean out the hole of all dust and cuttings. (3) Push Nylon Nail- ... It through the material to be fastened and base material until ... head of anchor body is snug up to the fixture. (4) Drive the expander pin ... home to complete the fastening. To remove the fastener, simply insert a ... . Anchor Length: Thickness of material to be fastened plus minimum embedment ... on a Nylon Nail-It are transferred to the material that it is installed in. ... If the anchors are installed too close together, it can cause an interaction of the ... | |
| is an anchoring/fastening system that allows fast and reliable attachment of 1/4" or ... 3/8" threaded rod into concrete, steel and wood. All HangerMates are ... , onepiece, cold-formed and machined alloy steel, with either a precision ... or straight drilled and tapped head. All anchors are yellow chromate zinc plated ... , please call 1-888-498- 5747 for all current code approvals. Material ... support applications in wood,, concrete and steel beams or joists. ... flush and then automatically disengage to prevent over driving anchor. (4) The ... anchor is now installed and ready to accept a threaded rod or component. ... For Masonry/Concrete (1) Insert appropriate HangerMate ... matched tolerance carbide-tipped drill bit into hammer or ... HangerMate anchor is now ready to accept a threaded rod or component. ... | |
