11 results for anchor fastener flush type found in 0.000 seconds

f 216.391.5352 www.confast.com SLEEVE ANCHOR The Sleeve Anchor is constructed of ... assembled into a complete ready-to-use anchor. The anchor consists of a threaded stud ... assembled on the stud to complete the anchor. The anchor works on a true expansion ... , wedging it outward and locking the anchor into the base material. TECHNICAL INFO ... S.A. Specifications FF-S-325, Group II, Type 3, Class 3. Applications: Medium duty ... B94, 12-77 with the same size bit as anchor diameter. (2) Clean hole with wire ... brush. (3) Make sure nut is flush with the top threaded part of anchor. ... Insert anchor assembly through mounting holes in ... and into the base material. Push anchor assembly until washer is snug against ... three or four full turns or until anchor is tightly secured to the base material ...

.5352 www.confast.com DROP-IN A Drop-In anchor consists of a zinc plated steel tubular ... , flangeless top that allows either flush or countersunk installation. the bottom ... . Minimum embedment for satisfactory anchor performance is 4-1/2 bolt diameters. ... S.A. Specification FF-S-325 Group Vlll, type 1. Applications: Medium duty into ... the outside diameter of the drop-in anchor being used. Make sure hole depth ... air or a blow out bulb. (3) Drive anchor into hole flush with the surface of the ... ) Using the proper setting tool for the anchor, expand anchor by inserting the setting ... tool into the anchor and set with several solid hammer blows ... . The anchor is set properly when shoulder of ... setting tool is flush with the top of anchor. To set anchor below surface: Drill hole ...

.391.5352 www.confast.com MACHINE SCREW ANCHOR The Machine Screw Anchor is made up of ... from turning in the sleeve. All size anchors, except the 3/4" size, are preassembled ... .S.A. Specification FF-S-325, Group II, Type 2, Class 1. Applications: Light to ... to a depth equal to the length of the anchor. Place the Machine Screw Anchor, base ... conical nut first, into the hole The anchor should be flush or slightly deeper than ... tool into the threaded bore of the anchor and press firmly against the lead alloy ... sleeve of the anchor. Using a hand hammer, strike the end of ... setting tool with repeated sharp blows. Anchor is set when the sleeve cannot be ... the object to be fastened over the anchor and bolt into place. The length of the ... portion of the internal threads of the anchor. Bolt Length: Thickness of material to ...

391.5352 www.confast.com LEADWOOD SCREW ANCHOR The cavity of the Leadwood screw anchor ... proper expansion in masonry. The anchor is split from the bottom up for most of ... of its length. The top end of the anchor tapers outward from the anchor diameter ... diameter at the outer end of the anchor, in combination with the longitudinal ... of initial expansion and prevents the anchor from turning in the masonry. As the ... screw progresses deeper into the anchor, the longitudinal ribs bite into the ... masonry, preventing the anchor from twisting and allowing the screw to ... G.S.A. Specification F-S-325, Group IV, Type 1. Applications: Light duty into ... hole size) to a depth equal to the anchor length, plus one-quarter inch (1/4") or ... of all dust and cuttings. (3) Place anchor into hole and with light hammer blows, ...

216.391.5352 www.confast.com LAG SHIELD ANCHOR This two-part expansion shield is ... of its length. The outside of the anchor has a series of circumferential ribs ... of its length. The back end of the anchor has two equally spaced ribs that ... as Zamak 5, a rust-proof material. The anchor comes in two lengths, short or long. ... The short lag shield is for anchoring in high grade concrete or where ... grade base material or where extra anchoring strength is required. TECHNICAL INFO ... .S.A. Specification FF-S-325, Group II, Type 1, Class 1 2. Zamak #5 Zinc Alloy meets ... equal to the length of the expansion anchor plus one half inch (1/2") or more. (2) ... and cuttings. (3) Place the expansion anchor, ribbed end first, into hole. Tap with a ... hammer until flush with the surface of base material. (4) ...

216.391.5352 www.confast.com METAL HIT ANCHOR The Metal Hit Anchor is a precision ... diecast, light-duty concrete anchor combining unusual toughness and ... remarkable strength. The Metal Hit anchor consists of a cylindrical zinc alloy ... a major portion of its length. The anchor body has a bore which runs through the ... .S.A. specifications FF-S-325, Group V, Type 2, Class 3. Applications: Light to ... in base material equal to diameter of anchor being used. Hole depth should be at ... least 1/4" deeper than the anchor embedment. (2) Clean out hole of all ... dust and shavings. (3) Insert Metal Hit Anchor , slit end first through material to be ... The bottom of the head must be sitting flush with the fixture plate. (4) Hammer nail ... flush into head of anchor body. The Metal Hit Anchor is now set ...

f 216.391.5352 www.confast.com STRIKE ANCHOR The strike anchor is an impact- ... expansion type concrete anchor. The body of the anchor is carbon steel ... hole extending the length of the anchor. The hardened drive pin comes inserted ... in the interior hole of the anchor. The anchor is threaded on the top end where the ... pin is inserted. The other end of the anchor has four equally spaced slots for a ... ribs extending the circumference of the anchor for a portion of its length. The entire ... anchor is yellow dicromate over zinc plating. ... .A. Standards G.S.A. FF-S-325, Group V, Type 2 Class 2, Meets load factors in ... a carbide bit the same diameter as the anchor being installed. (2) Place washer and ... nut on anchor, turning nut on to anchor as required. May be flush with top or ...

.com HANGAR MATE HangerMate is an anchoring/fastening system that allows fast and ... straight drilled and tapped head. All anchors are yellow chromate zinc plated. ... . Material Specifications: Each type of HangerMate anchor is made from ... upon request. Applications: HangerMate anchors are ideal for overhead vertical or ... gun. (2) Insert appropriate HangerMate anchor into drive socket. (3) Position the ... self-drilling point of the anchor at the intended point of installation ... 1800 rpm, install the HangerMate anchor. The drive socket's safety set feature ... will set the anchor flush and then automatically disengage to ... prevent over driving anchor. (4) The HangerMate anchor is now ... drills use bit ZE380; for keyed chuck-type drills use bit ZE360. (2) With the ... bit. (4) Insert appropriate HangerMate anchor into the drive sleeve. disengage hammer ...

. Its unique, slim design allows the fastener to make a small hole that does not ... the consistency of the drywall. The anchor has a single point that drills a clean ... , oversized head seals the hole with a flush mount. TECHNICAL INFO Applications: ... point into wallboard, while turning the anchor clockwise until it is seated flush with ... to be fastened plus 1" penetration into anchor equals screw length. Anchor Spacing: ... that it is installed in. If the anchors are installed too close together, it ... thus reducing the holding power of the anchor. When anchoring into low-density ... of the material. As a rule of thumb, anchors should be spaced 18 to 24 inches from ... low-density materials. Depending on the type of high density material, spacing may ...

bolt operates like no other. Each anchor has a one-piece steel anchoring channel ... and the cap. The legs snap off easily, flush with the wall. The Toggler bolt is also ... hand, pull ring so metal channel rests flush behind wall as you slide plastic cap ... with other hand until flange of cap is flush with wall. (3) Place thumb between ... , Push side to side snapping off straps flush with wall. (4) Insert bolt through item ... to be fastened and tighten until flush with fixture. Minimum clearance behind ... of base material equals screw length. Anchor Spacing: The forces on a Toggler brand ... that it is installed in. If the anchors are installed too close together, it ... thus reducing the holding power of the anchor. When anchoring into low-density ... of the material. As a rule of thumb, anchors should be spaced 18 to 24 inches from ...

positive locking action allows the anchor to become a rigid, weight-distributing ... truss. Anchors can be used in any material (masonite, ... above the minimum wall grip range. Anchors will perform as wedge or solid wall ... anchors in materials with thicknesses above ... Wall (1) Drill 5/16" hole. (2) Fold anchor, insert anchor in hole and tap flush ... with wall. (3) Insert key to pop anchor open behind hollow wall (not necessary ... or solid walls). (4) Place item over anchor, insert screw and tighten until screw is ... flush with fixture. Solid Base Material (1) ... /16" hole. (2) Clean out hole. (3) Fold anchor, insert anchor in hole and tap flush ... with base material. (4) Place item over anchor, insert screw and tighten until screw is ... flush. Anchor Length: The anchor chosen is based on the thickness of the ...