10 results for concrete anchor blocks found in 0.000 seconds

f 216.391.5352 www.confast.com SLEEVE ANCHOR The Sleeve Anchor is constructed of ... assembled into a complete ready-to-use anchor. The anchor consists of a threaded stud ... assembled on the stud to complete the anchor. The anchor works on a true expansion ... , wedging it outward and locking the anchor into the base material. TECHNICAL INFO ... 3. Applications: Medium duty into concrete, block and brick. Installation: (1) ... B94, 12-77 with the same size bit as anchor diameter. (2) Clean hole with wire ... is flush with the top threaded part of anchor. Insert anchor assembly through mounting ... and into the base material. Push anchor assembly until washer is snug against ... three or four full turns or until anchor is tightly secured to the base material ... . Anchor Length: The length of an anchor should equal minimum embedment, plus ...

.391.5352 www.confast.com MACHINE SCREW ANCHOR The Machine Screw Anchor is made up of ... from turning in the sleeve. All size anchors, except the 3/4" size, are preassembled ... Applications: Light to medium duty into concrete, block and brick. Installation: (1) ... to a depth equal to the length of the anchor. Place the Machine Screw Anchor, base ... conical nut first, into the hole The anchor should be flush or slightly deeper than ... tool into the threaded bore of the anchor and press firmly against the lead alloy ... sleeve of the anchor. Using a hand hammer, strike the end of ... setting tool with repeated sharp blows. Anchor is set when the sleeve cannot be ... the object to be fastened over the anchor and bolt into place. The length of the ... portion of the internal threads of the anchor. Bolt Length: Thickness of material to ...

391.5352 www.confast.com LEADWOOD SCREW ANCHOR The cavity of the Leadwood screw anchor ... proper expansion in masonry. The anchor is split from the bottom up for most of ... of its length. The top end of the anchor tapers outward from the anchor diameter ... diameter at the outer end of the anchor, in combination with the longitudinal ... of initial expansion and prevents the anchor from turning in the masonry. As the ... screw progresses deeper into the anchor, the longitudinal ribs bite into the ... masonry, preventing the anchor from twisting and allowing the screw to ... Type 1. Applications: Light duty into concrete, block and brick. Installation: (1) ... hole size) to a depth equal to the anchor length, plus one-quarter inch (1/4") or ... of all dust and cuttings. (3) Place anchor into hole and with light hammer blows, ...

.5352 www.confast.com SINGLE EXPANSION ANCHOR The Single expansion anchor consists of ... tubular shield during expansion. The anchor are of precision die-cast zinc alloy ... the expansion action at one end of the anchor distributes the anchored load ... throughout the length of the anchor. This expansion anchor is recommended ... A.E. 925. Applications: Medium duty in concrete, block and brick. Installation: (1) ... . (2) Place the Single Expansion anchor, nut end first, into the hole. The top ... end of the anchor should be flush or slightly below the ... the object to be fastened over the anchor in the base material and bolt into ... should engage 2/3 of the threads of the anchor. Anchor Spacing: The forces on a Single ... expansion anchor are transferred to the material that it ...

.5352 www.confast.com DOUBLE EXPANSION ANCHOR The Double expansion anchor consists of ... tubular shield during expansion. The anchors are of precision die-cast zinc alloy ... both ends of the shield distributes the anchored load throughout the length of the ... shield. This expansion anchor is recommended for shear loads or where ... A.E. 925. Applications: Medium duty in concrete, block and brick. Installation: (1) ... deeper than the length of the expansion anchor. Clean out the hole of all dust and ... . (2) Place the Double Expansion anchor, nut end first, into the hole. The top ... end of the anchor should be flush or slightly below the ... the object to be fastened over the anchor in the base material and bolt in to ... place. Anchor Spacing: The forces on a Double ... expansion anchor are transferred to the material that it ...

216.391.5352 www.confast.com LAG SHIELD ANCHOR This two-part expansion shield is ... of its length. The outside of the anchor has a series of circumferential ribs ... of its length. The back end of the anchor has two equally spaced ribs that ... as Zamak 5, a rust-proof material. The anchor comes in two lengths, short or long. ... The short lag shield is for anchoring in high grade concrete or where ... grade base material or where extra anchoring strength is required. TECHNICAL INFO ... Applications: Light to medium duty into concrete, block and brick. Installation: (1) ... equal to the length of the expansion anchor plus one half inch (1/2") or more. (2) ... and cuttings. (3) Place the expansion anchor, ribbed end first, into hole. Tap with a ... plus 1/2" equals Lag Screw length. Anchor Spacing: The forces on a Lag Shield ...

-formula polyamide resins. The nylon anchor consists of two parts, a cylindrical ... for a portion of its length. The anchor body has a concentric cavity, or bore, ... , Class 4. Applications: Light duty in concrete, block and brick. Installation: (1) ... and base material until head of anchor body is snug up to the fixture. (4) ... head of the expander pin an unscrew. Anchor Length: Thickness of material to be ... fastened plus minimum embedment equals anchor length. Anchor Spacing: The forces on ... that it is installed in. If the anchors are installed too close together, it ... thus reducing the holding power of the anchor. When anchoring into low-density ... of the material. As a rule of thumb, anchors should be spaced 18 to 24 inches from ... . SIZE DRILL BIT MINIMUM EMBEDMENT CONCRETE 3000 PSI Values shown are average ...

216.391.5352 www.confast.com METAL HIT ANCHOR The Metal Hit Anchor is a precision ... diecast, light-duty concrete anchor combining unusual toughness and ... remarkable strength. The Metal Hit anchor consists of a cylindrical zinc alloy ... a major portion of its length. The anchor body has a bore which runs through the ... Applications: Light to medium duty in concrete block and brick. Installation: (1) ... in base material equal to diameter of anchor being used. Hole depth should be at ... least 1/4" deeper than the anchor embedment. (2) Clean out hole of all ... dust and shavings. (3) Insert Metal Hit Anchor , slit end first through material to be ... . (4) Hammer nail flush into head of anchor body. The Metal Hit Anchor is now set ... . Anchor Length: Thickness of material to be ...

bolt operates like no other. Each anchor has a one-piece steel anchoring channel ... of base material equals screw length. Anchor Spacing: The forces on a Toggler brand ... that it is installed in. If the anchors are installed too close together, it ... thus reducing the holding power of the anchor. When anchoring into low-density ... of the material. As a rule of thumb, anchors should be spaced 18 to 24 inches from ... . SIZE GRIP RANGE 1 5/8" WALL BOARD CONCRETE BLOCK STEEL PLATE (1) Long strap ...

positive locking action allows the anchor to become a rigid, weight-distributing ... truss. Anchors can be used in any material (masonite, ... plywood, paneling, concrete, drywall, etc.) of any thickness above ... the minimum wall grip range. Anchors will perform as wedge or solid wall ... anchors in materials with thicknesses above ... Applications: Light to medium duty in concrete, brick,block, drywall, masonite, plywood ... Wall (1) Drill 5/16" hole. (2) Fold anchor, insert anchor in hole and tap flush ... with wall. (3) Insert key to pop anchor open behind hollow wall (not necessary ... or solid walls). (4) Place item over anchor, insert screw and tighten until screw is ... /16" hole. (2) Clean out hole. (3) Fold anchor, insert anchor in hole and tap flush ... with base material. (4) Place item over anchor, insert screw and tighten until screw is ...