Catalog: Concrete Fasteners Catalog | |
| Anchor Lag Shield Anchor Tapcon Concrete Screws Nylon Nail-It Metal Hit Anchor ... www.confast.com YOUR ONE SOURCE FOR CONCRETE FASTENERS ... | |
| driven into the hole drilled in the concrete. The other end of the rod has a necked ... Applications: Medium to heavy duty into concrete. Installation: (1) Drill hole into ... concrete with a carbide tipped masonry drill bit ... in the fixture or directly into the concrete and hammer it in to the drilled hole ... are below the surface of the fixture/concrete. (3) Turn the nut by hand until the unit ... depth. The depth of the hole in the concrete should be the length of the wedge ... depth to accommodate a minor amount of concrete cutting which may not be able to be ... that it is installed in. If the anchors are installed too close together, it ... of the anchor. As a rule of thumb, the concrete anchor industry has established a ... ) anchor diameters for spacing between anchors and five (5) anchor diameters from an ... | |
| -1/4 1-1/4 1-1/4 5-1/2 3-1/4 *These anchors come with the standard thread length or ... | |
| 3. Applications: Medium duty into concrete, block and brick. Installation: (1) ... depth to accommodate a minor amount of concrete cuttings which may not be able to be ... that it is installed in. If the anchors are installed too close together, it ... ) anchor diameters for spacing between anchors and five (5) anchor diameters from an ... | |
| type 1. Applications: Medium duty into concrete. Installation: (1) Drill hole into ... concrete with a carbide tipped masonry drill bit ... minimum embedment. (2) Clean out concrete dust from hole using a wire brush, ... into hole flush with the surface of the concrete. (4) Using the proper setting tool for ... that it is installed in. If the anchors are installed too close together, it ... ) anchor diameters for spacing between anchors and five (5) anchor diameters from an ... of the load condition, spacing between anchors should be increased. Bolt Length: Bolt ... | |
| from turning in the sleeve. All size anchors, except the 3/4" size, are preassembled ... Applications: Light to medium duty into concrete, block and brick. Installation: (1) ... that it is installed in. If the anchors are installed too close together, it ... ) anchor diameters for spacing between anchors and five (5) anchor diameters from the ... of the load conditions, spacing between anchors should be increased. ANCHOR SIZE ... LENGTH HOLE SIZE PULL-OUT 6000 PSI CONCRETE Values shown are average ultimate ... | |
| Type 1. Applications: Light duty into concrete, block and brick. Installation: (1) ... that it is installed in. If the anchors are installed too close together, it ... ) anchor diameters for spacing between anchors and five (5) anchor diameters from an ... SIZE SCREW SIZE PULL-OUT 3000 PSI CONCRETE Values shown are average ultimate ... | |
| A.E. 925. Applications: Medium duty in concrete, block and brick. Installation: (1) ... that it is installed in. If the anchors are installed too close together, it ... ) anchor diameters for spacing between anchors and five (5) anchor diameters from an ... HOLE SIZE BOLT DIA. PULL-OUT 6000 PSI CONCRETE Values shown are average ultimate ... | |
| tubular shield during expansion. The anchors are of precision die-cast zinc alloy ... A.E. 925. Applications: Medium duty in concrete, block and brick. Installation: (1) ... that it is installed in. If the anchors are installed too close together, it ... ) anchor diameters for spacing between anchors and five (5) anchor diameters from an ... HOLE SIZE BOLT DIA. PULL-OUT 5000 PSI CONCRETE Values shown are average ultimate ... | |
| shield is for anchoring in high grade concrete or where thickness of base material ... Applications: Light to medium duty into concrete, block and brick. Installation: (1) ... that it is installed in. If the anchors are installed too close together, it ... ) anchor diameters for spacing between anchors and five (5) anchor diameters from an ... SIZE ANCHOR LENGTH PULL-OUT 6000 PSI CONCRETE TECHNICAL DATA 1/4" Short 1/2" 1" ... | |
| , Class 4. Applications: Light duty in concrete, block and brick. Installation: (1) ... that it is installed in. If the anchors are installed too close together, it ... of the material. As a rule of thumb, anchors should be spaced 18 to 24 inches from ... . SIZE DRILL BIT MINIMUM EMBEDMENT CONCRETE 3000 PSI Values shown are average ... | |
| is a precision diecast, light-duty concrete anchor combining unusual toughness and ... Applications: Light to medium duty in concrete block and brick. Installation: (1) ... that it is installed in. If the anchors are installed too close together, it ... ) anchor diameters for spacing between anchors and five (5) anchor diameters from an ... | |
| .com SPLIT DRIVE ANCHOR Split Drive anchors are a one-piece, all steel concrete ... anchor. Split drive anchors are manufactured with through hardened ... at the base. When driven into the concrete hole, these halves are compressed. Once ... compensates for poor grade or old concrete. Split Drive Anchor can come with either ... Applications: light to medium duty in concrete. Installation: (1) Drill hole in ... concrete with carbide tipped bit meeting ANSI ... that it is installed in. If the anchors are installed too close together, it ... ) anchor diameters for spacing between anchors and five (5) anchor diameters from an ... | |
| anchor is an impact-expansion type concrete anchor. The body of the anchor is ... . Applications: Medium to heavy into concrete. Installation: (1) Drill hole of ... material to be fastened and in to the concrete base material. (4) Using a proper sized ... | |
| of 1/4" or 3/8" threaded rod into concrete, steel and wood. All HangerMates are ... straight drilled and tapped head. All anchors are yellow chromate zinc plated. ... upon request. Applications: HangerMate anchors are ideal for overhead vertical or ... support applications in wood,, concrete and steel beams or joists. ... threaded rod or component. For Masonry/Concrete (1) Insert appropriate HangerMate ... a threaded rod or component. ITEM CONCRETE WOOD 16 GA 16 W/NUT 14 GA 14 W/NUT ... | |
| that it is installed in. If the anchors are installed too close together, it ... of the material. As a rule of thumb, anchors should be spaced 18 to 24 inches from ... | |
| that it is installed in. If the anchors are installed too close together, it ... of the material. As a rule of thumb, anchors should be spaced 18 to 24 inches from ... . SIZE GRIP RANGE 1 5/8" WALL BOARD CONCRETE BLOCK STEEL PLATE (1) Long strap ... | |
| a rigid, weight-distributing truss. Anchors can be used in any material (masonite, ... plywood, paneling, concrete, drywall, etc.) of any thickness above ... the minimum wall grip range. Anchors will perform as wedge or solid wall ... anchors in materials with thicknesses above ... Applications: Light to medium duty in concrete, brick,block, drywall, masonite, plywood ... be used in solid base material such as concrete. Anchor Spacing: The forces on a ... that it is installed in. If the anchors are installed too close together, it ... of the material. As a rule of thumb, anchors should be spaced 18 to 24 inches from ... | |
