Catalog: Concrete Fasteners Catalog
Company/Brand: Concrete Fastening Systems
concrete screw in Concrete Fasteners Catalog by Concrete Fastening Systems
Sleeve Anchor Drop-In Machine Screw Anchor Leadwood Screw Anchor Single ... Anchor Lag Shield Anchor Tapcon Concrete Screws Nylon Nail-It Metal Hit Anchor ... www.confast.com YOUR ONE SOURCE FOR CONCRETE FASTENERS ...
f 216.391.5352 www.confast.com MACHINE SCREW ANCHOR The Machine Screw Anchor is made ... Applications: Light to medium duty into concrete, block and brick. Installation: (1) ... length of the anchor. Place the Machine Screw Anchor, base end of the conical nut ... and bolt into place. The length of the screw or bolt should equal the thickness of ... length required to ensure that the screw engages a major portion of the internal ... Anchor Spacing: The forces on a Machine Screw Anchor are transferred to the base ... LENGTH HOLE SIZE PULL-OUT 6000 PSI CONCRETE Values shown are average ultimate ...
f 216.391.5352 www.confast.com LEADWOOD SCREW ANCHOR The cavity of the Leadwood screw ... from turning in the masonry. As the screw progresses deeper into the anchor, the ... anchor from twisting and allowing the screw to form its own threads. TECHNICAL ... Type 1. Applications: Light duty into concrete, block and brick. Installation: (1) ... surface of base material. (4) Insert screw through fixture into anchor and tighten ... . Screw Length: Thickness of material to be ... for complete expansion of anchor equals screw length. Anchor Spacing: The forces on ... a Leadwood screw anchor are transferred to the material ... be increased. ANCHOR SIZE HOLE SIZE SCREW SIZE PULL-OUT 3000 PSI CONCRETE ...
threads permit easy turning of the lag screw without lubrication. Once fastened, an ... shield is for anchoring in high grade concrete or where thickness of base material ... Applications: Light to medium duty into concrete, block and brick. Installation: (1) ... the shield in the base material and screw in the lag screw. (5) If the lag screw ... or tighten before the head of the lag screw mates up against the object being ... by hand hammering the head of the lag screw until flush to the object being ... fastened. Re-tighten the lag screw to complete the expansion of the shield ... to secure the material being fastened. Screw Length: Thickness of material to be ... Lag Shield length plus 1/2" equals Lag Screw length. Anchor Spacing: The forces on ... SIZE ANCHOR LENGTH PULL-OUT 6000 PSI CONCRETE TECHNICAL DATA 1/4" Short 1/2" 1" ...
f 216.391.5352 www.confast.com TAPCON CONCRETE SCREWS The TapCon brand concrete screw ... cuts threads in a predrilled hole in concrete, brick or block. The screw has ... power and stability. The TapCon brand concrete screw is available in both 3/16" or 1/4 ... or a 5/16" hex washer head. All screws are plated using the Stalgard coating ... for ease of installation. TapCon screws are also available in 410 stainless ... a silver Stalgard. The stainless steel screws have shown no red rust in salt spray ... Applications: Light to medium duty in concrete, brick and block. Installation: (1) ... using the drill bit provided with the screws. The depth of the hole must be at least ... point of Tapcon into hole and drive screw in using a nut drive or #3 bit tip. Do ... not over torque the screw. Screw Length: The length of the TapCon ...
of 1/4" or 3/8" threaded rod into concrete, steel and wood. All HangerMates are ... support applications in wood,, concrete and steel beams or joists. ... recessed drive socket ZE215 into corded screw gun (min. 4.5 amps) or appropriate ... cordless screw gun. (2) Insert appropriate HangerMate ... point of installation and with the screw gun operation at approximately 1800 rpm ... threaded rod or component. For Masonry/Concrete (1) Insert appropriate HangerMate ... a threaded rod or component. ITEM CONCRETE WOOD 16 GA 16 W/NUT 14 GA 14 W/NUT ...
and tighten the proper size sheet metal screw. A one inch 1" minimum thread engagement ... is recommended. Screw Length: Thickness of material to be ... plus 1" penetration into anchor equals screw length. Anchor Spacing: The forces on ...
clearance behind wall is 1-7/8" Screw Length: Thickness of material to be ... plus thickness of base material equals screw length. Anchor Spacing: The forces on ... . SIZE GRIP RANGE 1 5/8" WALL BOARD CONCRETE BLOCK STEEL PLATE (1) Long strap ...
to be inserted in to the hole. As the screw passes through the body, it draws in ... material (masonite, plywood, paneling, concrete, drywall, etc.) of any thickness above ... Applications: Light to medium duty in concrete, brick,block, drywall, masonite, plywood ... ). (4) Place item over anchor, insert screw and tighten until screw is flush with ... . (4) Place item over anchor, insert screw and tighten until screw is flush. ... be used in solid base material such as concrete. Anchor Spacing: The forces on a ...
