9 results for concrete to steel plate found in 0.000 seconds

into a single unit. The carbon steel rod is threaded for a portion of its ... end of the threaded portion is rounded to protect the threads from damage while ... driven into the hole drilled in the concrete. The other end of the rod has a necked ... at the end of which it tapers outwardly to the full diameter of the rod. A ... formed universal clip made of carbon steel is permanently assembled around the ... necked down diameter to complete the anchor. Each package ... of Building Officials (ICBO) carbon steel only, Board of Standards and Appeals ( ... 11, Type 4, Class Applications: Medium to heavy duty into concrete. Installation ... : (1) Drill hole into concrete with a carbide tipped masonry drill bit ... conforming to ANSI B94, 12-77, the same size as the ... in place and being used as a template to locate the ThunderStud anchor, the ...

Anchor is constructed of high quality steel parts. Each part is zinc plated and ... assembled into a complete ready-to-use anchor. The anchor consists of a ... hex nut are then assembled on the stud to complete the anchor. The anchor works ... 3. Applications: Medium duty into concrete, block and brick. Installation: (1) ... in fixture or directly through material to be fastened and into the base material ... , using a carbide bit conforming to ANSI B94, 12-77 with the same size bit ... . (3) Make sure nut is flush with the top threaded part of anchor. Insert anchor ... or until anchor is tightly secured to the base material. Anchor Length: The ... . This will provide some extra depth to accommodate a minor amount of concrete ... cuttings which may not be able to be cleaned out of hole. Anchor Spacing ...

-IN A Drop-In anchor consists of a zinc plated steel tubular expansion shield and a ... plug is case hardened and tempered to prevent galling and binding during ... shield also has a smooth, flangeless top that allows either flush or countersunk ... the bottom lip of the shield is tapered to allow maximum depth and holding power. ... type 1. Applications: Medium duty into concrete. Installation: (1) Drill hole into ... concrete with a carbide tipped masonry drill bit ... conforming to ANSI B94, 12-77, matching the bit size ... minimum embedment. (2) Clean out concrete dust from hole using a wire brush, ... into hole flush with the surface of the concrete. (4) Using the proper setting tool for ... expand anchor by inserting the setting tool into the anchor and set with several ...

f 216.391.5352 www.confast.com TAPCON CONCRETE SCREWS The TapCon brand concrete screw ... cuts threads in a predrilled hole in concrete, brick or block. The screw has ... power and stability. The TapCon brand concrete screw is available in both 3/16" or 1/4 ... a 5/16" hex washer head. All screws are plated using the Stalgard coating which ... are also available in 410 stainless steel finished with a silver Stalgard. The ... stainless steel screws have shown no red rust in salt ... . TECHNICAL INFO Applications: Light to medium duty in concrete, brick and ... the TapCon embedment. (2) Place object to be fastened over hole. (3) Insert point ... a nut drive or #3 bit tip. Do not over torque the screw. Screw Length: The length of ... the TapCon fastener to be used is determined by combining the ...

a cylindrical nylon shank or body and a steel pin expander. The shank is split a ... the slit terminates in the body. The steel pin expander is similar to a nail ... in the head. It is made of high carbon steel, properly heat treated and heavily ... plated with bright zinc for maximum corrosion ... , Class 4. Applications: Light duty in concrete, block and brick. Installation: (1) ... Push Nylon Nail-It through the material to be fastened and base material until ... head of anchor body is snug up to the fixture. (4) Drive the expander pin ... home to complete the fastening. To remove the fastener, simply insert a ... . Anchor Length: Thickness of material to be fastened plus minimum embedment ... on a Nylon Nail-It are transferred to the material that it is installed in. ... If the anchors are installed too close together, it can cause an interaction of the ...

is a precision diecast, light-duty concrete anchor combining unusual toughness and ... cylindrical zinc alloy body and a zinc plated steel pin expander. The shank, from the ... the slot terminates in the body. The steel pin expander is made of high carbon ... steel, properly heat treated, and heavily zinc ... plated for maximum corrosion resistance. ... , Type 2, Class 3. Applications: Light to medium duty in concrete block and brick ... : (1) Drill hole in base material equal to diameter of anchor being used. Hole ... , slit end first through material to be fastened and into hole. The bottom ... must be sitting flush with the fixture plate. (4) Hammer nail flush into head of ... . Anchor Length: Thickness of material to be fastened plus minimum embedment plus ...

anchor is an impact-expansion type concrete anchor. The body of the anchor is ... carbon steel with an interior hole extending the ... anchor. The anchor is threaded on the top end where the drive pin is inserted. ... A.S.T.M. E488488. Applications: Medium to heavy into concrete. Installation: (1 ... and nut on anchor, turning nut on to anchor as required. May be flush with ... top or turned on fully to provide stud finish. (3) With nut, ... , insert anchor through the material to be fastened and in to the concrete base ... on head of pin until pin is flush with top of anchor. Anchor is now properly set ... . (5) No need to torque nut to set anchor. Warning: Wear eye ... working load. Reference should be made to applicable codes for specific working ...

of 1/4" or 3/8" threaded rod into concrete, steel and wood. All HangerMates are ... , cold-formed and machined alloy steel, with either a precision crossdrilled or ... . All anchors are yellow chromate zinc plated. TECHNICAL INFO Approvals: Each ... anchor is made from different steel specifications. These specifications ... support applications in wood,, concrete and steel beams or joists. ... flush and then automatically disengage to prevent over driving anchor. (4) The ... anchor is now installed and ready to accept a threaded rod or component. ... For Masonry/Concrete (1) Insert appropriate HangerMate ... matched tolerance carbide-tipped drill bit into hammer or ... HangerMate anchor is now ready to accept a threaded rod or component. ... ITEM CONCRETE WOOD 16 GA 16 W/NUT 14 GA 14 W/NUT ...

498.5747 f 216.391.5352 www.confast.com TOGGLER BOLT The patented TOGGLER brand toggle ... no other. Each anchor has a one-piece steel anchoring channel pivoted on durable ... The sliding cap ratchets down the legs to securely "capture" the wall between the ... off easily, flush with the wall. The Toggler bolt is also available with a stainless ... steel channel. TECHNICAL INFO Applications: ... light to medium duty in hollow block, hollow ... thumb between plastic straps, Push side to side snapping off straps flush with ... wall. (4) Insert bolt through item to be fastened and tighten until flush ... 8" Screw Length: Thickness of material to be fastened plus thickness of base ... . Anchor Spacing: The forces on a Toggler brand toggle bolt are transferred to ... in. If the anchors are installed too close together, it can cause an ...