10 results for drill bit f found in 0.000 seconds

1 p 888.498.5747 f 216.391.5352 www.confast.com ... unit. The carbon steel rod is threaded for a portion of its length. The extreme ... is rounded to protect the threads from damage while the anchor is being driven ... into the hole drilled in the concrete. The other end of the ... has a necked down diameter, which runs for a short distance, at the end of which ... it tapers outwardly to the full diameter of the rod. A precision formed ... U.S. Government G.S.A. Specifications FF-S-325 Group 11, Type 4, Class Applications: ... duty into concrete. Installation: (1) Drill hole into concrete with a carbide ... tipped masonry drill bit conforming to ANSI B94, 12-77, the same ... as the ThunderStud wedge anchor. If the fixture being fastened is in place and being ...

3 p 888.498.5747 f 216.391.5352 www.confast.com SLEEVE ... of a threaded stud with an outwardly flared cone-shaped end. A tubular expander ... U.S. Government G.S.A. Specifications FF-S-325, Group II, Type 3, Class 3. ... , block and brick. Installation: (1) Drill hole through mounting holes in fixture ... or directly through material to be fastened and into the base material, using a ... carbide bit conforming to ANSI B94, 12-77 with the ... same size bit as anchor diameter. (2) Clean hole with ... wire brush. (3) Make sure nut is flush with the top threaded part of anchor. ... assembly through mounting holes in fixture and into the base material. Push anchor ... until washer is snug against the fixture. (4) Turn nut by hand until snugged up. ... nut with a wrench (use a screwdriver for flat/round heads), approximately three ...

4 p 888.498.5747 f 216.391.5352 www.confast.com DROP-IN A ... during expansion. The shield has four equally spaced slots for a portion of ... knurled. The shield also has a smooth, flangeless top that allows either flush or ... depth and holding power. SIZE LENGTH DRILL BIT THRD. LENGTH BOLT DIA. PULL-OUT ... guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as ... should be made in applicable codes for specific working ratio. Minimum ... embedment for satisfactory anchor performance is 4-1/ ... U.S. government G.S.A. Specification FF-S-325 Group Vlll, type 1. Applications: ... duty into concrete. Installation: (1) Drill hole into concrete with a carbide ... tipped masonry drill bit conforming to ANSI B94, 12-77, matching ...

10 p 888.498.5747 f 216.391.5352 www.confast.com TAPCON ... 3/16" or 1/4" diameters with either a flat phillips #3 countersunk or a 5/16" hex ... extended life and additional lubricity for ease of installation. TapCon screws are ... also available in 410 stainless steel finished with a silver Stalgard. The stainless ... , brick and block. Installation: (1) Drill hole into base material using the drill ... bit provided with the screws. The depth of ... embedment. (2) Place object to be fastened over hole. (3) Insert point of Tapcon ... drive screw in using a nut drive or #3 bit tip. Do not over torque the screw. ... Screw Length: The length of the TapCon fastener to be used is determined by combining ... 1-3/4" embedment be used in determining fastener length. The diameter of the fastener ...

11 p 888.498.5747 f 216.391.5352 www.confast.com NYLON NAIL ... -It is injection-molded, thermoplastic-formula polyamide resins. The nylon anchor ... is split a major portion of its length from the bottom up and has a series of ... circumferential ribs running for a portion of its length. The anchor ... the head thickness and into the shank for a depth just beyond the point where the ... expander is similar to a nail except for the specially designed thread in a ... and heavily plated with bright zinc for maximum corrosion resistance. The ... Approvals: Meets G.S.A. Specifications FF-S-325, Group V, Type 2, Class 4. Applications ... , block and brick. Installation: (1) Drill hole in base material using a carbide ... tipped bit matching the diameter of the Nylon Nail ...

12 p 888.498.5747 f 216.391.5352 www.confast.com METAL HIT ... plated steel pin expander. The shank, from the bottom up, is split a major portion ... the head thickness and into the shank for a depth just beyond the point where the ... heat treated, and heavily zinc plated for maximum corrosion resistance. TECHNICAL ... Approvals: Meets G.S.A. specifications FF-S-325, Group V, Type 2, Class 3. Applications ... block and brick. Installation: (1) Drill hole in base material equal to diameter ... 3) Insert Metal Hit Anchor , slit end first through material to be fastened and ... The bottom of the head must be sitting flush with the fixture plate. (4) Hammer nail ... flush into head of anchor body. The Metal Hit ... Length: Thickness of material to be fastened plus minimum embedment plus 1/4" equals ...

13 p 888.498.5747 f 216.391.5352 www.confast.com SPLIT ... original shape. This exerts tremendous force upon the inside walls of the hole, ... . The positive expansion compensates for poor grade or old concrete. Split Drive ... Anchor can come with either a flat counter sunk head or a round head. ... Approvals: Meets G.S.A. Specification FF-S-325, Group VI. Applications: light to ... duty in concrete. Installation: (1) Drill hole in concrete with carbide tipped ... bit meeting ANSI standards. Hole should be ... drilled minimum embedment or deeper, plus 1/4 ... out of hole. (3) Insert anchor through fixture and into hole. (4) Hammer anchor into ... hole flush with the top of fixture. Anchor Length: Thickness of material ... to be fastened plus minimum embedment plus 1/4" equals ...

14 p 888.498.5747 f 216.391.5352 www.confast.com STRIKE ... . The other end of the anchor has four equally spaced slots for a portion of ... the circumference of the anchor for a portion of its length. The entire ... or exceeds G.S.A. Standards G.S.A. FF-S-325, Group V, Type 2 Class 2, Meets load ... factors in compliance with A.N.S.I. A58-1, ... heavy into concrete. Installation: (1) Drill hole of sufficient depth using a ... carbide bit the same diameter as the anchor being ... nut on to anchor as required. May be flush with top or turned on fully to provide ... stud finish. (3) With nut, washer, and set-pin in ... anchor through the material to be fastened and in to the concrete base material. ( ... strikes on head of pin until pin is flush with top of anchor. Anchor is now ...

15 p 888.498.5747 f 216.391.5352 www.confast.com HANGAR ... MATE HangerMate is an anchoring/fastening system that allows fast and reliable ... are made of a solid, onepiece, cold-formed and machined alloy steel, with either a ... precision crossdrilled or straight drilled and tapped head. All anchors are yellow ... , please call 1-888-498- 5747 for all current code approvals. Material ... Each type of HangerMate anchor is made from different steel specifications. These ... : HangerMate anchors are ideal for overhead vertical or horizontal support ... steel beams or joists. Installation: For Metal or Wood (1) Insert HangerMate ... drive socket. (3) Position the self-drilling point of the anchor at the intended ... anchor. The drive socket's safety set feature will set the anchor flush and then ...

16 p 888.498.5747 f 216.391.5352 www.confast.com WALL ... DRILLER The Wall Driller is injection molded of engineered ... . Its unique, slim design allows the fastener to make a small hole that does not ... . The anchor has a single point that drills a clean hole and prevents paper damage ... , oversized head seals the hole with a flush mount. TECHNICAL INFO Applications: ... . Installation: (1) Insert #2 Phillips bit tip into head of wall driller. (2) ... the anchor clockwise until it is seated flush with the wall. (3) Place fixture over ... Length: Thickness of material to be fastened plus 1" penetration into anchor equals ... screw length. Anchor Spacing: The forces on a Wall Driller are transferred to ... , it can cause an interaction of the forces, thus reducing the holding power of the ...