Catalog: Concrete Fasteners Catalog
Company/Brand: Concrete Fastening Systems
drills bits in Concrete Fasteners Catalog by Concrete Fastening Systems
1 p 888.498.5747 f 216.391.5352 www.confast.com THUNDERSTUD The ThunderStud wedge anchor consists of two pieces, permanently preassembled into a single unit. The carbon steel rod is threaded for a portion of its length. The extreme end of the threaded portion is rounded to protect the threads from damage while the anchor is being driven into the hole drilled in the concrete. The other end of the rod has a necked down diameter, which runs for a short distance, at the end of which it tapers outwardly to the full diameter of the rod. A precision formed universal clip made of carbon steel is permanently ...
3 p 888.498.5747 f 216.391.5352 www.confast.com SLEEVE ANCHOR The Sleeve Anchor is constructed of high quality steel parts. Each part is zinc plated and assembled into a complete ready-to-use anchor. The anchor consists of a threaded stud with an outwardly flared cone-shaped end. A tubular expander sleeve is assembled over the stud and butted against the small diameter of the cone. A washer and hex nut are then assembled on the stud to complete the anchor. The anchor works on a true expansion principle: Tightening of the nut pulls the coneshaped stud end into the expander sleeve, wedging it outward ...
4 p 888.498.5747 f 216.391.5352 www.confast.com DROP-IN A Drop-In anchor consists of a zinc plated steel tubular expansion shield and a solid, cone-shaped expander plug. The expander plug is case hardened and tempered to prevent galling and binding during expansion. The shield has four equally spaced slots for a portion of its length, the bottom part may be knurled. The shield also has a smooth, flangeless top that allows either flush or countersunk installation. the bottom lip of the shield is tapered to allow maximum depth and holding power. SIZE LENGTH DRILL BIT THRD. LENGTH BOLT DIA. PULL-OUT ...
drilled with Elco carbide tipped drill bits. Designated holding power depends on the ...
11 p 888.498.5747 f 216.391.5352 www.confast.com NYLON NAIL-IT This Nylon Nail-It is injection-molded, thermoplastic-formula polyamide resins. The nylon anchor consists of two parts, a cylindrical nylon shank or body and a steel pin expander. The shank is split a major portion of its length from the bottom up and has a series of circumferential ribs running for a portion of its length. The anchor body has a concentric cavity, or bore, which runs through the head thickness and into the shank for a depth just beyond the point where the slit terminates in the body. The steel pin expander is similar ...
12 p 888.498.5747 f 216.391.5352 www.confast.com METAL HIT ANCHOR The Metal Hit Anchor is a precision diecast, light-duty concrete anchor combining unusual toughness and remarkable strength. The Metal Hit anchor consists of a cylindrical zinc alloy body and a zinc plated steel pin expander. The shank, from the bottom up, is split a major portion of its length. The anchor body has a bore which runs through the head thickness and into the shank for a depth just beyond the point where the slot terminates in the body. The steel pin expander is made of high carbon steel, properly heat treated, and heavily ...
13 p 888.498.5747 f 216.391.5352 www.confast.com SPLIT DRIVE ANCHOR Split Drive anchors are a one-piece, all steel concrete anchor. Split drive anchors are manufactured with through hardened, heat treated carbon steel. The anchor has two sheared, preexpanded halves at the base. When driven into the concrete hole, these halves are compressed. Once an anchor is set, the two halves will continually try to regain their original shape. This exerts tremendous force upon the inside walls of the hole, resulting in low "slip" rates and increased vibration resistance. The positive expansion compensates for ...
14 p 888.498.5747 f 216.391.5352 www.confast.com STRIKE ANCHOR The strike anchor is an impact-expansion type concrete anchor. The body of the anchor is carbon steel with an interior hole extending the length of the anchor. The hardened drive pin comes inserted in the interior hole of the anchor. The anchor is threaded on the top end where the drive pin is inserted. The other end of the anchor has four equally spaced slots for a portion of its length, with ribs extending the circumference of the anchor for a portion of its length. The entire anchor is yellow dicromate over zinc plating. TECHNICAL ...
or rotary hammer drill. For SDS-drive drills use bit ZE380; for keyed chuck-type ... drills use bit ZE360. (2) With the drill in ...
. The anchor has a single point that drills a clean hole and prevents paper damage ...
