6 results for drive anchor found in 0.000 seconds

TABLE OF CONTENTS: Thunderstud Sleeve Anchor Drop-In Machine Screw Anchor Leadwood ... Screw Anchor Single Expansion Anchor Double Expansion Anchor Lag Shield ... Anchor Tapcon Concrete Screws Nylon Nail-It ... Metal Hit Anchor Split Drive Anchor Strike Anchor Hangar Mate Wall Driller ...

.5352 www.confast.com DROP-IN A Drop-In anchor consists of a zinc plated steel tubular ... . Minimum embedment for satisfactory anchor performance is 4-1/2 bolt diameters. ... the outside diameter of the drop-in anchor being used. Make sure hole depth ... compressed air or a blow out bulb. (3) Drive anchor into hole flush with the surface ... ) Using the proper setting tool for the anchor, expand anchor by inserting the setting ... tool into the anchor and set with several solid hammer blows ... . The anchor is set properly when shoulder of ... setting tool is flush with the top of anchor. To set anchor below surface: Drill hole ... deeper than anchor length. Thread bolt into anchor. Hammer ... anchor into hole until bolt head is a desired ... depth. Remove bolt and set anchor with setting tool as described above. ...

-formula polyamide resins. The nylon anchor consists of two parts, a cylindrical ... for a portion of its length. The anchor body has a concentric cavity, or bore, ... and base material until head of anchor body is snug up to the fixture. (4) ... Drive the expander pin home to complete the ... head of the expander pin an unscrew. Anchor Length: Thickness of material to be ... fastened plus minimum embedment equals anchor length. Anchor Spacing: The forces on ... that it is installed in. If the anchors are installed too close together, it ... thus reducing the holding power of the anchor. When anchoring into low-density ... of the material. As a rule of thumb, anchors should be spaced 18 to 24 inches from ... . Minimum embedment for satisfactory anchor performance is 4-1/2 bolt diameters. ...

f 216.391.5352 www.confast.com SPLIT DRIVE ANCHOR Split Drive anchors are a one- ... piece, all steel concrete anchor. Split drive anchors are manufactured with through ... , heat treated carbon steel. The anchor has two sheared, preexpanded halves at ... the base. When driven into the concrete hole, these halves ... are compressed. Once an anchor is set, the two halves will continually ... for poor grade or old concrete. Split Drive Anchor can come with either a flat ... 2) Clean dust out of hole. (3) Insert anchor through fixture and into hole. (4) ... Hammer anchor into hole flush with the top of fixture ... . Anchor Length: Thickness of material to be ... plus minimum embedment plus 1/4" equals anchor length. Anchor Spacing: The forces on ... a Split Drive Anchor are transferred to the material that it ...

f 216.391.5352 www.confast.com STRIKE ANCHOR The strike anchor is an impact- ... expansion type concrete anchor. The body of the anchor is carbon steel ... hole extending the length of the anchor. The hardened drive pin comes inserted ... in the interior hole of the anchor. The anchor is threaded on the top end where the ... drive pin is inserted. The other end of the ... anchor has four equally spaced slots for a ... ribs extending the circumference of the anchor for a portion of its length. The entire ... anchor is yellow dicromate over zinc plating. ... a carbide bit the same diameter as the anchor being installed. (2) Place washer and ... nut on anchor, turning nut on to anchor as required. May be flush with top or ... , washer, and set-pin in place, insert anchor through the material to be fastened and ...

.com HANGAR MATE HangerMate is an anchoring/fastening system that allows fast and ... straight drilled and tapped head. All anchors are yellow chromate zinc plated. ... Specifications: Each type of HangerMate anchor is made from different steel ... upon request. Applications: HangerMate anchors are ideal for overhead vertical or ... or Wood (1) Insert HangerMate recessed drive socket ZE215 into corded screw gun (min ... gun. (2) Insert appropriate HangerMate anchor into drive socket. (3) Position the ... self-drilling point of the anchor at the intended point of installation ... 1800 rpm, install the HangerMate anchor. The drive socket's safety set feature ... will set the anchor flush and then automatically disengage ... to prevent over driving anchor. (4) The HangerMate anchor is now ...