6 results for drive in concrete anchors found in 0.000 seconds

: Thunderstud Sleeve Anchor Drop-In Machine Screw Anchor Leadwood Screw ... Anchor Lag Shield Anchor Tapcon Concrete Screws Nylon Nail-It Metal Hit Anchor ... Split Drive Anchor Strike Anchor Hangar Mate Wall ... www.confast.com YOUR ONE SOURCE FOR CONCRETE FASTENERS ...

f 216.391.5352 www.confast.com DROP-IN A Drop-In anchor consists of a zinc ... that allows either flush or countersunk installation. the bottom lip of the shield is tapered ... working load. Reference should be made in applicable codes for specific working ... 1" 1-3/16" 3/4" 13600 lb. TECHNICAL INFO Approvals: Listed by Underwriters ... Laboratories (UL), International Conference of Building Officials (ICBO ... Vlll, type 1. Applications: Medium duty into concrete. Installation: (1) Drill hole ... into concrete with a carbide tipped masonry drill bit ... with the outside diameter of the drop-in anchor being used. Make sure hole depth ... minimum embedment. (2) Clean out concrete dust from hole using a wire brush, ... compressed air or a blow out bulb. (3) Drive anchor into hole flush with the surface ...

com NYLON NAIL-IT This Nylon Nail-It is injection-molded, thermoplastic-formula polyamide resins ... runs through the head thickness and into the shank for a depth just beyond the ... point where the slit terminates in the body. The steel pin expander is ... for the specially designed thread in a section of its shank and the ... screwdriver slot in the head. It is made of high carbon ... pin lock the assembly. TECHNICAL INFO Approvals: Meets G.S.A. Specifications ... 2, Class 4. Applications: Light duty in concrete, block and brick. ... Installation: (1) Drill hole in base material using a carbide tipped ... body is snug up to the fixture. (4) Drive the expander pin home to complete the ... . To remove the fastener, simply insert a screwdriver into the slot in the head ...

f 216.391.5352 www.confast.com SPLIT DRIVE ANCHOR Split Drive anchors are a one- ... piece, all steel concrete anchor. Split drive anchors are manufactured with through ... , preexpanded halves at the base. When driven into the concrete hole, these halves ... . This exerts tremendous force upon the inside walls of the hole, resulting in low " ... slip" rates and increased vibration resistance. The positive ... compensates for poor grade or old concrete. Split Drive Anchor can come with either ... sunk head or a round head. TECHNICAL INFO Approvals: Meets G.S.A. Specification ... VI. Applications: light to medium duty in concrete. Installation: (1) Drill hole ... in concrete with carbide tipped bit meeting ANSI ... 1/4" (2) Clean dust out of hole. (3) Insert anchor through fixture and into hole. ( ...

anchor is an impact-expansion type concrete anchor. The body of the anchor is ... carbon steel with an interior hole extending the length of the anchor ... . The hardened drive pin comes inserted in the interior hole of the anchor. The ... is threaded on the top end where the drive pin is inserted. The other end of the ... dicromate over zinc plating. TECHNICAL INFO Approvals: Meets I.C.B.O. standards ... V, Type 2 Class 2, Meets load factors in compliance with A.N.S.I. A58-1, Meets ... plating standard in compliance with A.S.T.M. E488488. ... Applications: Medium to heavy into concrete. Installation: (1) Drill hole of ... the same diameter as the anchor being installed. (2) Place washer and nut on anchor, ... . (3) With nut, washer, and set-pin in place, insert anchor through the ...

attachment of 1/4" or 3/8" threaded rod into concrete, steel and wood. All ... straight drilled and tapped head. All anchors are yellow chromate zinc plated. ... TECHNICAL INFO Approvals: Each different HangerMate ... upon request. Applications: HangerMate anchors are ideal for overhead vertical or ... horizontal support applications in wood,, concrete and steel beams or ... joists. Installation: For Metal or Wood (1) Insert HangerMate ... recessed drive socket ZE215 into corded screw gun (min. 4.5 amps) or ... appropriate cordless screw gun. (2) Insert appropriate HangerMate anchor into ... drive socket. (3) Position the self-drilling ... point of the anchor at the intended point of installation and with the ... operation at approximately 1800 rpm, install the HangerMate anchor. The drive socket ...