Catalog: Concrete Fasteners Catalog | |
| p 888.498.5747 f 216.391.5352 1192 East 40th Street Cleveland, Ohio 44114 www.confast.com PRODUCT CATALOG YOUR ONE SOURCE FOR CONCRETE FASTENERS | |
| p 888.498.5747 f 216.391.5352 TABLE OF CONTENTS: Thunderstud Sleeve Anchor Drop-In Machine Screw Anchor Leadwood Screw Anchor Single Expansion Anchor Double Expansion Anchor Lag Shield Anchor Tapcon Concrete Screws Nylon Nail-It Metal Hit Anchor Split Drive Anchor Strike Anchor Hangar Mate Wall Driller Toggler Bolt Plastic Toggler 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1192 East 40th Street Cleveland, Ohio 44114 www.confast.com YOUR ONE SOURCE FOR CONCRETE FASTENERS | |
| or four full turns, to complete the fastening. Anchor Length: Minimum embedment, plus ... | |
| 2 p 888.498.5747 f 216.391.5352 www.confast.com THUNDERSTUD LENGTH IDENTIFICATION SYSTEM TECHNICAL DATA ANCHOR DIAMETER (in.) EMBED. DEPTH (in.) Torque Ft/Lb 2000 PSI 4000 PSI 6000 PSI Tension (LB) Shear (LB) Tension (LB) Shear (LB) Tension (LB) Shear (LB) 1/4 5-10 1-1/8 1-3/4 2-3/4 1170 1841 1975 1443 1443 1443 1771 2408 2748 1813 1813 1813 2773 2773 2830 2635 2635 2635 3/8 25-30 1-1/2 3 5 1631 3229 4075 4318 4318 4318 3636 5653 6328 5121 5121 5121 4448 5975 6360 6232 6232 6232 1/2 50-60 2-1/4 4 6 3999 6336 6902 7419 7419 7419 6714 ... | |
| 3 p 888.498.5747 f 216.391.5352 www.confast.com SLEEVE ANCHOR The Sleeve Anchor is constructed of high quality steel parts. Each part is zinc plated and assembled into a complete ready-to-use anchor. The anchor consists of a threaded stud with an outwardly flared cone-shaped end. A tubular expander sleeve is assembled over the stud and butted against the small diameter of the cone. A washer and hex nut are then assembled on the stud to complete the anchor. The anchor works on a true expansion principle: Tightening of the nut pulls the coneshaped stud end into the expander sleeve, wedging it outward ... | |
| 4 p 888.498.5747 f 216.391.5352 www.confast.com DROP-IN A Drop-In anchor consists of a zinc plated steel tubular expansion shield and a solid, cone-shaped expander plug. The expander plug is case hardened and tempered to prevent galling and binding during expansion. The shield has four equally spaced slots for a portion of its length, the bottom part may be knurled. The shield also has a smooth, flangeless top that allows either flush or countersunk installation. the bottom lip of the shield is tapered to allow maximum depth and holding power. SIZE LENGTH DRILL BIT THRD. LENGTH BOLT DIA. PULL-OUT ... | |
| 5 p 888.498.5747 f 216.391.5352 www.confast.com MACHINE SCREW ANCHOR The Machine Screw Anchor is made up of an antimonial lead alloy sleeve and a zinc alloy (Zamak 5) internally threaded cone with a series of integral ribs or lugs. The ribs prevent the cone shaped nut from turning in the sleeve. All size anchors, except the 3/4" size, are preassembled into a single, self contained unit. All units are made of 100% rust proof material. TECHNICAL INFO Approvals: Meets G.S.A. Specification FF-S-325, Group II, Type 2, Class 1. Applications: Light to medium duty into concrete, block and brick. Installation: ... | |
| 6 p 888.498.5747 f 216.391.5352 www.confast.com LEADWOOD SCREW ANCHOR The cavity of the Leadwood screw anchor tapers and is designed to facilitate proper expansion in masonry. The anchor is split from the bottom up for most of its length and has longitudinal ribs for a portion of its length. The top end of the anchor tapers outward from the anchor diameter into a tubular thin section cone. The tapered diameter at the outer end of the anchor, in combination with the longitudinal split, facilitates ease of initial expansion and prevents the anchor from turning in the masonry. As the screw progresses ... | |
| 7 p 888.498.5747 f 216.391.5352 www.confast.com SINGLE EXPANSION ANCHOR The Single expansion anchor consists of a nut, a cone and a tubular shield preassembled as a single unit. The two piece tubular shield is bound together with one spring band. It contains a wedge shaped nut at one end. Integral lugs on the nut and cone keep the wedges from turning in the tubular shield during expansion. The anchor are of precision die-cast zinc alloy commonly known as Zamak 5. the expansion action at one end of the anchor distributes the anchored load throughout the length of the anchor. This expansion anchor ... | |
| 8 p 888.498.5747 f 216.391.5352 www.confast.com DOUBLE EXPANSION ANCHOR The Double expansion anchor consists of a nut, a cone and a tubular shield preassembled as a single unit. The two piece tubular shield is bound together with two spring bands. It contains a wedge shaped nut at one end and a wedge shaped hollow cone at the the other end. Integral lugs on the nut and cone keep the wedges from turning in the tubular shield during expansion. The anchors are of precision die-cast zinc alloy commonly known as Zamak 5. The expansion action at both ends of the shield distributes the anchored load throughout ... | |
| 9 p 888.498.5747 f 216.391.5352 www.confast.com LAG SHIELD ANCHOR This two-part expansion shield is preassembled into a self-contained single unit. The shell-like unit has tapered internal threads for a portion of its length. The outside of the anchor has a series of circumferential ribs starting at the bottom and running for a major portion of its length. The back end of the anchor has two equally spaced ribs that protrude beyond its diameter and run for a portion of its length. Precision internal threads permit easy turning of the lag screw without lubrication. Once fastened, an object may be ... | |
| 10 p 888.498.5747 f 216.391.5352 www.confast.com TAPCON CONCRETE SCREWS The TapCon brand concrete screw cuts threads in a predrilled hole in concrete, brick or block. The screw has alternating raised and lowered threads with diamond cut notches which provide exceptional holding power and stability. The TapCon brand concrete screw is available in both 3/16" or 1/4" diameters with either a flat phillips #3 countersunk or a 5/16" hex washer head. All screws are plated using the Stalgard coating which provides extended life and additional lubricity for ease of installation. TapCon screws are also available ... | |
| the expander pin home to complete the fastening. To remove the fastener, simply insert a ... | |
| 12 p 888.498.5747 f 216.391.5352 www.confast.com METAL HIT ANCHOR The Metal Hit Anchor is a precision diecast, light-duty concrete anchor combining unusual toughness and remarkable strength. The Metal Hit anchor consists of a cylindrical zinc alloy body and a zinc plated steel pin expander. The shank, from the bottom up, is split a major portion of its length. The anchor body has a bore which runs through the head thickness and into the shank for a depth just beyond the point where the slot terminates in the body. The steel pin expander is made of high carbon steel, properly heat treated, and heavily ... | |
| 13 p 888.498.5747 f 216.391.5352 www.confast.com SPLIT DRIVE ANCHOR Split Drive anchors are a one-piece, all steel concrete anchor. Split drive anchors are manufactured with through hardened, heat treated carbon steel. The anchor has two sheared, preexpanded halves at the base. When driven into the concrete hole, these halves are compressed. Once an anchor is set, the two halves will continually try to regain their original shape. This exerts tremendous force upon the inside walls of the hole, resulting in low "slip" rates and increased vibration resistance. The positive expansion compensates for ... | |
| 14 p 888.498.5747 f 216.391.5352 www.confast.com STRIKE ANCHOR The strike anchor is an impact-expansion type concrete anchor. The body of the anchor is carbon steel with an interior hole extending the length of the anchor. The hardened drive pin comes inserted in the interior hole of the anchor. The anchor is threaded on the top end where the drive pin is inserted. The other end of the anchor has four equally spaced slots for a portion of its length, with ribs extending the circumference of the anchor for a portion of its length. The entire anchor is yellow dicromate over zinc plating. TECHNICAL ... | |
| HANGAR MATE HangerMate is an anchoring/fastening system that allows fast and reliable ... | |
| 16 p 888.498.5747 f 216.391.5352 www.confast.com WALL DRILLER The Wall Driller is injection molded of engineered plastic or long lasting Zamak. Its unique, slim design allows the fastener to make a small hole that does not disrupt the consistency of the drywall. The anchor has a single point that drills a clean hole and prevents paper damage. The deep cutting threads provide strong engagement and resists stripping out. The tapered, oversized head seals the hole with a flush mount. TECHNICAL INFO Applications: Light duty into wallboard. Do not use overhead. Installation: (1) Insert #2 Phillips ... | |
| 17 p 888.498.5747 f 216.391.5352 www.confast.com TOGGLER BOLT The patented TOGGLER brand toggle bolt operates like no other. Each anchor has a one-piece steel anchoring channel pivoted on durable installation legs. The sliding cap ratchets down the legs to securely "capture" the wall between the channel and the cap. The legs snap off easily, flush with the wall. The Toggler bolt is also available with a stainless steel channel. TECHNICAL INFO Applications: light to medium duty in hollow block, hollow brick, wall board, paneling, plaster, fiberglass and composite panels. Installation: (1) Drill ... | |
| 18 p 888.498.5747 f 216.391.5352 www.confast.com PLASTIC TOGGLER The plastic Toggler consists of four legs and a body. The four legs are joined by hinges to form a diamond shape which attaches to the side of the body. The body has a hole through the center and webs on the sides to resist spinning during installation. The legs collapse to form a tonjue, which allow them to be inserted in to the hole. As the screw passes through the body, it draws in and expands the legs for double holing power. The key-activated positive locking action allows the anchor to become a rigid, weight-distributing truss. ... | |
