9 results for ff s found in 0.000 seconds

pieces, permanently preassembled into a single unit. The carbon steel rod is threaded ... necked down diameter, which runs for a short distance, at the end of which it tapers ... formed universal clip made of carbon steel is permanently assembled around the ... of Building Officials (ICBO) carbon steel only, Board of Standards and Appeals ( ... BSA), City of L.A. Meets or exceeds U.S. Government G.S.A. Specifications FF-S- ... bit conforming to ANSI B94, 12-77, the same size as the ThunderStud wedge anchor. ... , the mounting hole in the fixture should afford clearance for the universal ... wedge clip on the stud. (2) Clean hole, place the ThunderStud ...

498.5747 f 216.391.5352 www.confast.com SLEEVE ANCHOR The Sleeve Anchor is constructed ... of high quality steel parts. Each part is zinc plated and ... . The anchor consists of a threaded stud with an outwardly flared cone-shaped ... end. A tubular expander sleeve is assembled over the stud and butted ... against the small diameter of the cone. A washer and hex ... nut are then assembled on the stud to complete the anchor. The anchor ... of the nut pulls the coneshaped stud end into the expander sleeve, wedging ... of Building Officials (ICBO), Board of Standards and Appeals (BSA), City of L.A., Meets ... or exceeds U.S. Government G.S.A. Specifications FF-S-325, Group II, Type 3, Class 3. ...

-In anchor consists of a zinc plated steel tubular expansion shield and a solid, ... cone-shaped expander plug. The expander plug is ... and binding during expansion. The shield has four equally spaced slots for a ... , the bottom part may be knurled. The shield also has a smooth, flangeless top that ... installation. the bottom lip of the shield is tapered to allow maximum depth and ... holding power. SIZE LENGTH DRILL BIT THRD. LENGTH BOLT ... DIA. PULL-OUT Values shown are average ultimate values and are ... as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally ... accepted as a safe working load. Reference should be made ... in applicable codes for specific working ratio. Minimum embedment for ...

f 216.391.5352 www.confast.com MACHINE SCREW ANCHOR The Machine Screw Anchor is made ... up of an antimonial lead alloy sleeve and a zinc alloy (Zamak 5) internally ... threaded cone with a series of integral ribs or lugs. The ribs ... prevent the cone shaped nut from turning in the sleeve. All ... size anchors, except the 3/4" size, are preassembled into a single, self ... . TECHNICAL INFO Approvals: Meets G.S.A. Specification FF-S-325, Group II, Type ... 1) Drill hole of recommended diameter (see chart below) into the base material to ... length of the anchor. Place the Machine Screw Anchor, base end of the conical nut ... first, into the hole The anchor should be flush or slightly deeper than the ...

5747 f 216.391.5352 www.confast.com LAG SHIELD ANCHOR This two-part expansion shield ... is preassembled into a self-contained single unit. The shell-like unit has tapered ... length. The outside of the anchor has a series of circumferential ribs starting at the ... back end of the anchor has two equally spaced ribs that protrude beyond its diameter ... threads permit easy turning of the lag screw without lubrication. Once fastened, an ... . The anchor comes in two lengths, short or long. The short lag shield is for ... prohibits the use of a longer length shield. The long Lag shield is for use in lower ... base material or where extra anchoring strength is required. TECHNICAL INFO Approvals: ...

of two parts, a cylindrical nylon shank or body and a steel pin expander. The ... shank is split a major portion of its length from the ... bottom up and has a series of circumferential ribs running for a ... through the head thickness and into the shank for a depth just beyond the point where ... the slit terminates in the body. The steel pin expander is similar to a nail ... except for the specially designed thread in a section of its ... shank and the screwdriver slot in the head. It is made of high carbon ... steel, properly heat treated and heavily ... for maximum corrosion resistance. The specially designed threads and head on the ... . TECHNICAL INFO Approvals: Meets G.S.A. Specifications FF-S-325, Group V, Type ...

unusual toughness and remarkable strength. The Metal Hit anchor consists of a ... zinc alloy body and a zinc plated steel pin expander. The shank, from the ... bottom up, is split a major portion of its length. The ... through the head thickness and into the shank for a depth just beyond the point where ... the slot terminates in the body. The steel pin expander is made of high carbon ... steel, properly heat treated, and heavily zinc ... . TECHNICAL INFO Approvals: Meets G.S.A. specifications FF-S-325, Group V, Type ... of anchor being used. Hole depth should be at least 1/4" deeper than the anchor ... . (2) Clean out hole of all dust and shavings. (3) Insert Metal Hit Anchor , slit end ...

498.5747 f 216.391.5352 www.confast.com SPLIT DRIVE ANCHOR Split Drive anchors are a ... one-piece, all steel concrete anchor. Split drive anchors are manufactured with ... through hardened, heat treated carbon steel. The anchor has two sheared, preexpanded ... are compressed. Once an anchor is set, the two halves will continually try to ... regain their original shape. This exerts tremendous force upon the ... walls of the hole, resulting in low "slip" rates and increased vibration ... for poor grade or old concrete. Split Drive Anchor can come with either a ... flat counter sunk head or a round head. TECHNICAL INFO ... Approvals: Meets G.S.A. Specification FF-S-325, Group VI. Applications: light to ...

498.5747 f 216.391.5352 www.confast.com STRIKE ANCHOR The strike anchor is an impact- ... . The body of the anchor is carbon steel with an interior hole extending the ... end of the anchor has four equally spaced slots for a portion of its length, with ... INFO Approvals: Meets I.C.B.O. standards report #4194, Meets City of Los Angeles ... Approval #25109, Meets or exceeds G.S.A. Standards G.S.A. FF-S-325, Group V, ... load factors in compliance with A.N.S.I. A58-1, Meets plating standard in ... compliance with A.S.T.M. E488488. Applications: Medium to heavy ... . Installation: (1) Drill hole of sufficient depth using a carbide bit the same ... with top or turned on fully to provide stud finish. (3) With nut, washer, and set- ...