Catalog: Concrete Fasteners Catalog | |
| the anchor is being driven into the hole drilled in the concrete. The other end ... into concrete. Installation: (1) Drill hole into concrete with a carbide tipped ... the ThunderStud anchor, the mounting hole in the fixture should afford clearance ... wedge clip on the stud. (2) Clean hole, place the ThunderStud wedge anchor ... through the hole in the fixture or directly into the ... and hammer it in to the drilled hole until the threads are below the surface ... wedge anchor requires no maximum hole depth. The depth of the hole in the ... may not be able to be cleaned out of hole Anchor Spacing: The forces on a ... | |
| and brick. Installation: (1) Drill hole through mounting holes in fixture or ... size bit as anchor diameter. (2) Clean hole with wire brush. (3) Make sure nut is ... Insert anchor assembly through mounting holes in fixture and into the base material. ... . The Sleeve anchor requires no maximum hole depth. The depth of the hole in the ... may not be able to be cleaned out of hole. Anchor Spacing: The forces on a Sleeve ... should be increased. SIZE BOLT DIA. HOLE SIZE HEAD STYLE MIN. EMBED PULL-OUT ... | |
| into concrete. Installation: (1) Drill hole into concrete with a carbide tipped ... drop-in anchor being used. Make sure hole depth exceeds minimum embedment. (2) ... Clean out concrete dust from hole using a wire brush, compressed air or a ... blow out bulb. (3) Drive anchor into hole flush with the surface of the concrete ... . To set anchor below surface: Drill hole deeper than anchor length. Thread bolt ... into anchor. Hammer anchor into hole until bolt head is a desired depth. ... | |
| and brick. Installation: (1) Drill hole of recommended diameter (see chart ... end of the conical nut first, into the hole The anchor should be flush or slightly ... surface of the base material. A deeper hole should be used when making attachments ... increased. ANCHOR SIZE ANCHOR LENGTH HOLE SIZE PULL-OUT 6000 PSI CONCRETE ... | |
| and brick. Installation: (1) Drill hole into the base material (see chart below ... for recommended hole size) to a depth equal to the anchor ... inch (1/4") or more. (2) Clean out hole of all dust and cuttings. (3) Place ... anchor into hole and with light hammer blows, tap anchor ... should be increased. ANCHOR SIZE HOLE SIZE SCREW SIZE PULL-OUT 3000 PSI ... | |
| and brick. Installation: (1) Drill hole of recommended diameter, see chart ... of the expansion shield. Clean out the hole of all dust and cuttings. (2) Place the ... anchor, nut end first, into the hole. The top end of the anchor should be ... length. ANCHOR SIZE ANCHOR LENGTH HOLE SIZE BOLT DIA. PULL-OUT 6000 PSI ... | |
| and brick. Installation: (1) Drill hole of recommended diameter, see chart ... of the expansion anchor. Clean out the hole of all dust and cuttings. (2) Place the ... anchor, nut end first, into the hole. The top end of the anchor should be ... length. ANCHOR SIZE ANCHOR LENGTH HOLE SIZE BOLT DIA. PULL-OUT 5000 PSI ... | |
| and brick. Installation: (1) Drill hole of recommended diameter, into the base ... half inch (1/2") or more. (2) Clean the hole of all dust and cuttings. (3) Place the ... anchor, ribbed end first, into hole. Tap with a hammer until flush with the ... shield should be driven deeper into the hole by hand hammering the head of the lag ... should be increased. ANCHOR SIZE HOLE SIZE ANCHOR LENGTH PULL-OUT 6000 PSI ... | |
| screw cuts threads in a predrilled hole in concrete, brick or block. The screw ... and block. Installation: (1) Drill hole into base material using the drill bit ... with the screws. The depth of the hole must be at least 1/4" deeper than the ... . (2) Place object to be fastened over hole. (3) Insert point of Tapcon into hole ... box of TapCon fasteners. The correct hole must be drilled for the screw to obtain ... holding values. In all cases the hole must be at least 1/4" deeper than the ... values are based on close-tolerance holes drilled with Elco carbide tipped drill ... , depth of embedment, and proper hole size. These figures are offered only as ... | |
| and brick. Installation: (1) Drill hole in base material using a carbide tipped ... the Nylon Nail-it being used. Make sure hole is 1/4" deeper than expected embedment ... . (2) Clean out the hole of all dust and cuttings. (3) Push ... | |
| and brick. Installation: (1) Drill hole in base material equal to diameter of ... anchor being used. Hole depth should be at least 1/4" deeper ... the anchor embedment. (2) Clean out hole of all dust and shavings. (3) Insert ... material to be fastened and into hole. The bottom of the head must be sitting ... | |
| the base. When driven into the concrete hole, these halves are compressed. Once an ... force upon the inside walls of the hole, resulting in low "slip" rates and ... in concrete. Installation: (1) Drill hole in concrete with carbide tipped bit ... meeting ANSI standards. Hole should be drilled minimum embedment or ... deeper, plus 1/4" (2) Clean dust out of hole. (3) Insert anchor through fixture and ... into hole. (4) Hammer anchor into hole flush with the top of fixture. Anchor ... | |
| anchor is carbon steel with an interior hole extending the length of the anchor. The ... pin comes inserted in the interior hole of the anchor. The anchor is threaded ... into concrete. Installation: (1) Drill hole of sufficient depth using a carbide bit ... | |
| drive socket. (3) Position the self-drilling point of the anchor at the intended ... of the HangerMate anchor into drilled hole and drive until the safety set feature ... | |
| allows the fastener to make a small hole that does not disrupt the consistency ... has a single point that drills a clean hole and prevents paper damage. The deep ... . The tapered, oversized head seals the hole with a flush mount. TECHNICAL INFO ... with the wall. (3) Place fixture over hole and tighten the proper size sheet metal ... | |
| : (1) Drill appropriate sized hole. Hold metal channel flat alongside ... straps and slide channel through hole. (2) With one hand, pull ring so metal ... | |
| to the side of the body. The body has a hole through the center and webs on the ... allow them to be inserted in to the hole. As the screw passes through the body, ... : Hollow Wall (1) Drill 5/16" hole. (2) Fold anchor, insert anchor in hole ... . Solid Base Material (1) Drill 5/16" hole. (2) Clean out hole. (3) Fold anchor, ... insert anchor in hole and tap flush with base material. (4) ... | |
