Page 16 of Concrete Fasteners Catalog by Concrete Fastening Systems

14 p 888.498.5747 f 216.391.5352 www.confast.com STRIKE ANCHOR The strike anchor is an impact-expansion type concrete anchor. The body of the anchor is carbon steel with an interior hole extending the length of the anchor. The hardened drive pin comes inserted in the interior hole of the anchor. The anchor is threaded on the top end where the drive pin is inserted. The other end of the anchor has four equally spaced slots for a portion of its length, with ribs extending the circumference of the anchor for a portion of its length. The entire anchor is yellow dicromate over zinc plating. TECHNICAL INFO Approvals: Meets I.C.B.O. standards report #4194, Meets City of Los Angeles Approval #25109, Meets or exceeds G.S.A. Standards G.S.A. FF-S-325, Group V, Type 2 Class 2, Meets load factors in compliance with A.N.S.I. A58-1, Meets plating standard in compliance with A.S.T.M. E488488. Applications: Medium to heavy into concrete. Installation: (1) Drill hole of sufficient depth using a carbide bit the same diameter as the anchor being installed. (2) Place washer and nut on anchor, turning nut on to anchor as required. May be flush with top or turned on fully to provide stud finish. (3) With nut, washer, and set-pin in place, insert anchor through the material to be fastened and in to the concrete base material. (4) Using a proper sized hammer, set pin with several sharp and square strikes on head of pin until pin is flush with top of anchor. Anchor is now properly set. (5) No need to torque nut to set anchor. Warning: Wear eye protection. ANCHOR SIZE THREAD LENGTH MIN. EMB. BIT SIZE SPACE BETWEEN EDGE DISTANCE PULL-OUT 2000 PSI SHEAR 2000 PSI Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load. Reference should be made to applicable codes for specific working ratio. Critical applications ibratory, shock loads, overhead installations, etc. may require a safety factor of as much as 10:1, or more. TECHNICAL DATA 1/4" x 1-3/4" 5/8" 1" 1/4" 3-1/2" 1-3/4" 900 lb. 1600 lb. 1/4" x 2-3/8" 3/4" 1" 1/4" 3-1/2" 1-3/4" 900 lb. 1600 lb. 1/4" x 3" 3/4" 1" 1/4" 3-1/2" 1-3/4" 900 lb. 1600 lb. 5/16" x 2-3/4" 1" 1-1/4" 5/16" 3-1/2" 1-3/4" 1400 lb. 3000 lb. 5/16" x 4" 1-1/4" 1-1/4" 5/16" 3-1/2" 1-3/4" 1400 lb. 3000 lb. 3/8" x 2-3/8" 1" 1-1/2" 3/8" 4-3/8" 2-3/16" 2200 lb. 3400 lb. 3/8" x 3-1/2" 1-1/8" 1-1/2" 3/8" 4-3/8" 2-3/16" 2200 lb. 3400 lb. 3/8" x 5" 1" 1-1/2" 3/8" 4-3/8" 2-3/16" 2200 lb. 3400 lb. 1/2" x 2-3/4" 1" 2" 1/2" 5-1/4" 2-5/8" 3600 lb. 7200 lb. 1/2" x 3-1/2" 1-1/8" 2" 1/2" 5-1/4" 2-5/8" 3600 lb. 7200 lb. 1/2" x 4-3/4" 2" 2" 1/2" 5-1/4" 2-5/8" 3600 lb. 7200 lb. 1/2" x 6" 2" 2" 1/2" 5-1/4" 2-5/8" 3600 lb. 7200 lb. 5/8" x 4" 1-5/8" 2-1/2" 5/8" 6-1/8" 3-1/16" 5400 lb. 9200 lb. 5/8" x 6" 2" 5/8" 5/8" 6-1/8" 3-1/16" 5400 lb. 9200 lb. 3/4" x 5" 2" 3" 3/4" 7" 3-1/2" 7500 lb. 13500 lb. 3/4"x 6" 2" 3" 3/4" 7" 3-1/2" 7500 lb. 13500 lb.

[close]