Catalog: Concrete Fasteners Catalog
Company/Brand: Concrete Fastening Systems
screw anchor in Concrete Fasteners Catalog by Concrete Fastening Systems
TABLE OF CONTENTS: Thunderstud Sleeve Anchor Drop-In Machine Screw Anchor Leadwood ... Screw Anchor Single Expansion Anchor Double Expansion Anchor Lag Shield ... Anchor Tapcon Concrete Screws Nylon Nail-It Metal Hit Anchor Split ... Drive Anchor Strike Anchor Hangar Mate Wall Driller Toggler Bolt ...
f 216.391.5352 www.confast.com MACHINE SCREW ANCHOR The Machine Screw Anchor is made ... from turning in the sleeve. All size anchors, except the 3/4" size, are preassembled ... to a depth equal to the length of the anchor. Place the Machine Screw Anchor, base ... conical nut first, into the hole The anchor should be flush or slightly deeper than ... tool into the threaded bore of the anchor and press firmly against the lead alloy ... sleeve of the anchor. Using a hand hammer, strike the end of ... setting tool with repeated sharp blows. Anchor is set when the sleeve cannot be ... the object to be fastened over the anchor and bolt into place. The length of the ... screw or bolt should equal the thickness of ... length required to ensure that the screw engages a major portion of the internal ...
f 216.391.5352 www.confast.com LEADWOOD SCREW ANCHOR The cavity of the Leadwood screw ... anchor tapers and is designed to facilitate ... proper expansion in masonry. The anchor is split from the bottom up for most of ... of its length. The top end of the anchor tapers outward from the anchor diameter ... diameter at the outer end of the anchor, in combination with the longitudinal ... of initial expansion and prevents the anchor from turning in the masonry. As the ... screw progresses deeper into the anchor, the longitudinal ribs bite into the ... masonry, preventing the anchor from twisting and allowing the screw to ... hole size) to a depth equal to the anchor length, plus one-quarter inch (1/4") or ... of all dust and cuttings. (3) Place anchor into hole and with light hammer blows, ...
216.391.5352 www.confast.com LAG SHIELD ANCHOR This two-part expansion shield is ... of its length. The outside of the anchor has a series of circumferential ribs ... of its length. The back end of the anchor has two equally spaced ribs that ... threads permit easy turning of the lag screw without lubrication. Once fastened, an ... as Zamak 5, a rust-proof material. The anchor comes in two lengths, short or long. ... The short lag shield is for anchoring in high grade concrete or where ... grade base material or where extra anchoring strength is required. TECHNICAL INFO ... equal to the length of the expansion anchor plus one half inch (1/2") or more. (2) ... and cuttings. (3) Place the expansion anchor, ribbed end first, into hole. Tap with a ... the shield in the base material and screw in the lag screw. (5) If the lag screw ...
.com HANGAR MATE HangerMate is an anchoring/fastening system that allows fast and ... straight drilled and tapped head. All anchors are yellow chromate zinc plated. ... Specifications: Each type of HangerMate anchor is made from different steel ... upon request. Applications: HangerMate anchors are ideal for overhead vertical or ... recessed drive socket ZE215 into corded screw gun (min. 4.5 amps) or appropriate ... cordless screw gun. (2) Insert appropriate HangerMate ... anchor into drive socket. (3) Position the ... self-drilling point of the anchor at the intended point of installation ... and with the screw gun operation at approximately 1800 rpm ... , install the HangerMate anchor. The drive socket's safety set feature ... will set the anchor flush and then automatically disengage ... to prevent over driving anchor. (4) The HangerMate anchor is now ...
the consistency of the drywall. The anchor has a single point that drills a clean ... point into wallboard, while turning the anchor clockwise until it is seated flush with ... and tighten the proper size sheet metal screw. A one inch 1" minimum thread engagement ... is recommended. Screw Length: Thickness of material to be ... fastened plus 1" penetration into anchor equals screw length. Anchor Spacing: ... that it is installed in. If the anchors are installed too close together, it ... thus reducing the holding power of the anchor. When anchoring into low-density ... of the material. As a rule of thumb, anchors should be spaced 18 to 24 inches from ...
bolt operates like no other. Each anchor has a one-piece steel anchoring channel ... clearance behind wall is 1-7/8" Screw Length: Thickness of material to be ... plus thickness of base material equals screw length. Anchor Spacing: The forces on ... that it is installed in. If the anchors are installed too close together, it ... thus reducing the holding power of the anchor. When anchoring into low-density ... of the material. As a rule of thumb, anchors should be spaced 18 to 24 inches from ...
to be inserted in to the hole. As the screw passes through the body, it draws in ... positive locking action allows the anchor to become a rigid, weight-distributing ... truss. Anchors can be used in any material (masonite, ... above the minimum wall grip range. Anchors will perform as wedge or solid wall ... anchors in materials with thicknesses above ... Wall (1) Drill 5/16" hole. (2) Fold anchor, insert anchor in hole and tap flush ... with wall. (3) Insert key to pop anchor open behind hollow wall (not necessary ... or solid walls). (4) Place item over anchor, insert screw and tighten until screw is ... /16" hole. (2) Clean out hole. (3) Fold anchor, insert anchor in hole and tap flush ... with base material. (4) Place item over anchor, insert screw and tighten until screw is ...
