Catalog: Buckeye, Cleco, Dotco Fabrication Tools | |
| warning before mounting any abrasive wheel buffing wheel wire brush saw blade flap ... wheel or other product after all tool repairs ... s recommendations warning select proper guards for the application mount securely and ... properly always mount guards so that abrasive debris sparks etc are ... deflected away from the operator safety guards shall be in good condition any guard ... which has been subjected to a wheel failure shall be discarded and replaced ... warning speed rating of abrasive wheel buffing wheel wire brush saw blade flap ... wheel or other products used must equal or ... products and serious operator injury wheels must clearly show the rated speed for ... | |
| is detected remove and inspect the wheel and check the tool speed rpm use of ... over-speeding grinder or unbalanced wheels may result in serious injury warning ... 29cfr part 1910 warning each type of wheel wire brush saw blade flap wheel and ... collets etc which shall be used wheels must mount on tool s spindle freely but ... be tightened so as not to crack the wheel nuts must have full thread engagement ... the user warning regularly inspect all wheels etc and discard cracked chipped or ... damaged units redress out-of-balance wheels see regulations warning when mounting ... any grinding wheel the tool shall be run at operating ... bench for at least one minute a damaged wheel should fail within that time any ... suspect wheel of unknown origin shall not be used and ... | |
| type 1 wheel grinders 136 series nominal motor power ... kg length in mm spindle thread type 1 wheel capacity wheel guard size 136 series ... operating instructions service manual wheel guard flange wrench optional equipment ... wheel guards page 43 additional accessories pages 43 ... | |
| type 1 wheel grinders 31g 41g 42g 61g series ... 61g-533 61g-534 61g-535 housing type 1 wheel capacity free space rpm weight lbs kgs ... 1/2 x 1/2 3 x 1/2 4 x 1/2 type 1 wheel capacity 20,000 20,000 22,000 22,000 18 ... 620 kpa air pressure standard equipment wheel guard wheel flange spindle nut spindle ... | |
| type 1 wheel grinders 116 136 right angle series ... length in mm head height in mm type 1 wheel capacity wheel guard size 116 series ... operating instructions service manual wheel guard wheel adapter spindle wrench ... optional equipment wheel guards page 43 additional accessories pages 43 ... | |
| type 1 wheel grinders 15 right angle series nominal ... in length mm head height in mm type 1 wheel capacity wheel guard size 15 series ... operating instructions service manual wheel guard optional equipment wheel guards ... | |
| type 1 wheel grinders 500b horizontal series nominal ... lbs kg in length mm arbor size type 1 wheel capacity wheel guard size 500b series ... operating instructions service manual wheel guard flange wrench optional equipment ... wheel guards page 43 additional accessories pages 43 ... | |
| type 1 wheel grinders 1700 1900 horizontal series ... lbs kg in length mm arbor size type 1 wheel capacity wheel guard size 1700 series ... operating instructions service manual wheel guard flange wrench optional equipment ... wheel guards page 43 additional accessories pages 43 ... | |
| type 27 wheel grinders 136 vertical series nominal ... kg in length mm in height mm type 27 wheel capacity wheel guard size 136 series ... operating instructions service manual wheel guard flange wrench optional equipment ... wheel guards page 43 additional accessories pages 43 ... | |
| type 27 wheel grinders 31a 42h series nominal motor ... exhaust rear exhaust housing type 27 wheel capacity free space rpm weight lbs kgs ... of rapid select standard equipment wheel guard proper flanges spindle wrench ... | |
| type 27 wheel grinders 116 136 right angle series ... length in mm head height in mm type 27 wheel capacity wheel guard size 116 series ... operating instructions service manual wheel guard wheel adapter spindle wrench ... optional equipment for 4 1/2 type 27 wheels with 7/8 hole wheel guards page 43 ... | |
| type 27 28 wheel grinders 15 right angle vertical ... in length mm in height mm type 27 28 wheel capacity wheel guard size 115 right ... operating instructions service manual wheel guard flange wrench optional equipment ... wheel guards page 43 additional accessories pages 43 ... | |
| type 1 cut-off wheel grinders 31a 42h series nominal motor ... rear exhaust housing type 1 cut-off wheel capacity free speed rpm weight lbs kgs ... 620 kpa air pressure standard equipment wheel guard proper flanges spindle wrench ... | |
| type 27 28 wheel grinders 1200 vertical series nominal ... w/guard lbs kg in height mm type 27 28 wheel capacity wheel guard size 1200 series ... operating instructions service manual wheel guard spindle wrench optional ... equipment wheel guards page 43 additional accessories pages 43 ... | |
| type 27 28 wheel grinders 1700 1900 vertical series ... w/guard lbs kg in height mm type 27 28 wheel capacity wheel guard size 1700 series ... operating instructions service manual wheel guard spindle wrench optional ... equipment wheel guards page 43 additional accessories pages 43 ... | |
| type 6 11 wheel grinders 1200 vertical series nominal ... w/guard lbs kg in height mm type 6 11 wheel capacity wheel guard size 1200 series ... operating instructions service manual wheel guard spindle wrench wheel retainer ... washer bolt optional equipment wheel guards page 43 additional accessories pages 43 ... | |
| type 6 11 wheel grinders 1700 1900 vertical series ... w/guard lbs kg in height mm type 6 11 wheel capacity wheel guard size 1700 series ... instructions and service manual wheel guard spindle wrench wheel retainer ... washer bolt optional equipment wheel guards page 43 additional accessories pages 43 ... | |
| size code no 1/4 shank max speed cleco wheel guards tool series size part no speed ... ,000 66,000 50,000 40,000 33,000 type 1 wheel 116ra 136ra 116ra 136ra 116ra 136ra 136 ... ,000 25,000 9,000 12,000 6,000 type 27 wheel 15ra 136v 136v 116ra 136ra 116ra 136ra ... 16,500 13,500 16,500 11,500 type 28 wheel cone or taper 1/4 x 3/4 3/8 x 5/8 1 ... 000 66,000 50,000 40,000 type 6 11 cup wheel tree pointed 1/4 x 3/4 3/8 x 3/4 1/ ... | |
| 861997 1700v 1900v 861997 869204 4 1/2 wheel guard kit part no used on overhose for ... 849269 part no size used on type 27 28 wheel adapter kit part no used on rubber flex ... 1200v 1700v 1900v for 7/8 plain whole wheels rubber flex chuck collets tool series ... on 861804 861804 116 136 cone or plug wheel driving flange part no used on 869699 ... | |
| grinder accessories buckeye buckeye wheel guards tool series series guard number ... part no description type 1 cut-off wheel 31a 42h 42h 4 3 4 1.75 2 2 2 1/2 ... debris away from the work area type 1 wheel 31g 41g-501 41g-521 41g-502 41g-522 41g ... -147 81g-146 81g-147 depressed center wheel adapter adapt abrasive with a 7/8 ... 1021767 use with type 27 28 wheels overhose assemblies for use with ... -1508 8.0 2.4 type 27 depressed center wheel 31a 31a 31a 31a 42h 42h 3 4 4 thin 4 ... sander attachment part number contact wheel mounting tool spindle idler spindle ... | |
