Page 6 of Buckeye, Dotco, Gardner-Denver Pneumatic Power Motors by Cooper Power Tools

rotary vane 22 series s maximum motor power rotary vane 0.9 hp 0.67 kw s torque range 0.8 ­ 41.2 ft lbs 1.08 ­ 55.83 nm s non-reversible s rear exhaust 22m5340-60 · spindle rotation all models are right-hand rotation to order left-hand rotation models not reversible substitute d for the first ­ in the model number for round housing motors and v for the m in the model number for motors with flange and base mounting important threaded spindles have right-hand threads therefore use keyed shaft models only 50 for left-hand rotation 22-5340-60 rpm stall torque free weight lbs kg model number at max hp speed ft lbs nm gear ratio length page 7 overall pilot a in b in round housing ­ 1/2 diameter keyed spindle 22-5040-50 · 22-5041-50 22-5042-50 22-5340-50 22-5440-50 · 22-5940-50 · 22m5040-50 · 22m5041-50 22m5042-50 22m5340-50 22m5440-50 22m5940-50 215 320 470 1600 2350 11500 215 320 470 1600 2350 11500 430 640 940 3200 4700 23000 430 640 940 3200 4700 23000 41.2 28.4 19.6 5.8 4.0 0.8 41.2 28.4 19.6 5.8 4.0 .8 55.83 38.48 26.56 7.86 5.42 1.08 55.83 38.48 26.56 7.86 5.42 1.08 4.1 4.1 4.1 3.1 3.1 2.5 5.0 5.0 5.0 4.0 4.0 3.4 1.86 1.86 1.86 1.41 1.41 1.13 2.27 2.27 2.27 1.81 1.81 1.54 50.4:1 34.8:1 24:1 7.1:1 4.9:1 50.4:1 3.48:1 24:1 7.1:1 4.9:1 7.94 7.94 7.94 6.19 6.19 4.38 7.94 7.94 7.94 6.19 6.19 4.38 .25 .25 .25 .25 .25 .63 .25 .25 .25 .25 .25 .63 flange and base mounting ­ 1/2 diameter keyed spindle ·available on quotation basis only general air inlet 1/4 npt ­ side and rear air consumption 29 cfm 82 m3/min all tools performance rated 90psi 620 kpa air pressure ·optional terminations replace -50 in model number with the desired termination when ordering -38 0 1/4 capacity drill chuck 5000 rpm or less -51 1/16 3/8 capacity drill chuck 5000 rpm or less -53 5/64 1/2 capacity drill chuck 5000 rpm or less -60 1/2 20 threaded spindle -01 series 200 collet chuck for milling and routing -62 series k collet chuck for milling and routing standard equipment hex socket screw provided for closure of unused inlet flush fitting for lubrication of gears wrench for threaded spindle and collet chuck models 1/4 collet included with series 200 k collet chuck optional equipment exhaust mufflers remote-exhaust hoses air intake hoses spindle adapters and filter-lubricator-regulators available at extra cost any series 200 and k collet may be substituted at no additional cost important a 3/8 i.d air inlet hose may be used for runs up to 10 for longer runs use 1/2 i.d hoses when remote-exhaust hose is used the portion of air inlet hose inserted into the exhaust hose should not exceed 3/8 i.d approx .650 o.d planetary gears should be greased after every 250 hours with gear grease 450983 or equivalent for filters regulators and lubricators refer to page 68 if air line connector is used install at end of hose away from the tool concentricity on motors with round housings concentricity of spindle to o.d of housing is .003 tir 6 7

[close]