Page 28 of Material Removal Tools by Cooper Power Tools

router accessories router assemblies for use with dotco 12-10 12-20 and 12-25 series cutter shank capacity part number complete attachment nose housing bearing ring lock nut router housing part number router accessories dotco 10-43 series router template guides dimensions in inches a b c for use w/router bits up to tool series 12-10 12-20/12-25 12-20/12-25 12-12/12-22/12-27 1/4 1/4 3/8 1/4 14-2187 14-2180 14-2429 7197 14-2176 14-2176 14-2426 14-0508 14-0508 14-0533 14-0508 1098 1098 1068 1098 14-2082 14-2082 14-2082 n/a 14-1180 14-2180 14-2180 n/a 14-2180 internal bowed retaining ring 14-4019 14-4020 14-4021 5/16 3/8 9/16 3/8 7/16 5/8 3/16 5/16 3/16 1/4 5/16 1/2 c 14-4020 a b bottom of base rivet trimmer attachment for use on dotco 12-12 series front or rear exhaust collet models trims pop or blind rivets up to 3/16 diameter also suitable for shaving small welds micrometer adjustment controls height of cut to .001 runner pads minimize scratching of the work surface part no diameter shank length description recommended use 14-1723 for use with dotco 12-40 series part number tool series cutter shank capacity nose housing bearing retaining ring ball bearing 12-40 12-40 1/4 3/8 4272 4263 14-0508 14-0533 1098 1068 trimmer 14-1723 cutters 14-1732 14-1332 3/4 1/2 1/4 1/4 1 7/8 1 7/8 inverted cone carbide cylindrical carbide steel rivets shaving welds router guides for use on dotco 12-10 12-20 12-20 12-25 and 12-40 series 5/8-18nf .390 dia two handed router base use with front or rear exhaust collet models two handed control for router applications easy depth adjustment can also be used with 10-43 template guides cutters 14-2442 combination flush/bevel 22° laminate trimmer attachment part number series 14-1178 14-2178 dotco 12-10 series dotco 12-20 12-25 series offset 1/2 b dimension minus router bit dia the minimum router bit length oal to be used is determined by the formula oal 1-13/16 c+p series 12-10 oal 2 c+p series 12-20 12-25 c is the c dimension of the router guide and p is the desired protrusion of the router bit part number dimensions in abcd part number dimensions in abcd part number series for router bits with 1/4 shanks 14-2703 14-2400 14-2401 14-2402 14-2406 14-2407 14-2408 14-2411 14-2412 14-2413 14-2414 14-2417 14-2420 14-2421 14-2500 14-2501 14-2502 14-2505 14-2506 14-2507 14-2510 14-2511 14-2512 14-2600 3/4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 2 1/2 3/8 3/8 3/8 3/8 7/16 7/16 7/16 1/2 1/2 1/2 1/2 9/16 5/8 5/8 3/8 3/8 3/8 7/16 7/16 7/16 1/2 1/2 1/2 1/2 1/2 1/8 1/4 3/8 1/8 1/4 3/8 1/4 1/2 5/8 3/4 1/8 1/8 5/8 1/8 1/4 3/8 1/8 1/4 3/8 1/4 3/8 1/2 1/2 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 3/16 for router bits with 3/8 shanks 14-2531 14-2538 14-2539 14-2540 14-2541 14-2542 14-2893 14-2925 14-2544 14-2240 14-2632 14-2633 14-2634 14-2630 14-2635 14-2243 14-2636 14-2631 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1/2 1/2 1/2 9/16 9/16 9/16 5/8 5/8 5/8 1/2 1/2 1/2 9/16 9/16 9/16 5/8 5/8 5/8 3/8 1/2 5/8 3/8 1/2 5/8 3/8 1/2 5/8 3/8 1/2 5/8 3/8 1/2 5/8 3/8 1/2 5/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 1/8 14-1577 14-2577 dotco 12-10 series dotco 12-20 12-25 series important insert bit into collet as far as possible then pull out 1/16 and tighten collet in an emergency if it is necessary to pull out the bit more than 1/4 be sure to insert a short length of blank shank not to exceed 5/8 long in the bottom of the collet before inserting the bit 14-2178 14-2577 52 warning face eye protection must be worn while operating power tools per ansi b186.1 cutting tool maximum speed rating must equal or exceed speed of air tool 90psi 620 kpa follow cutting tool manufacturer s mounting operating instructions tools must be equipped with lock-off lever to be ce compliant warning face eye protection must be worn while operating power tools per ansi b186.1 cutting tool maximum speed rating must equal or exceed speed of air tool 90psi 620 kpa follow cutting tool manufacturer s mounting operating instructions tools must be equipped with lock-off lever to be ce compliant 53

[close]