Page 30 of Material Removal Tools by Cooper Power Tools

saw accessories saw accessories 14-1891 14-2928 14-2700 14-1742 part number diameter type maximum depth width of cut maximum rpm recommended use guidelines only part number diameter type maximum depth width of cut recommended use guidelines only saw blades ­ 1/4 arbor hole 14-1875 14-0930 14-1895 14-1890 14-1891 14-1892 14-1396 14-1395 14-1398 14-1400 1 1/4 1 1/4 1 1/2 2 2 2 1 1/2 2 1 1/2 2 high speed steel 22 teeth high speed steel 44 teeth high speed steel 22 teeth high speed steel 22 teeth high speed steel 44 teeth high speed steel 60 teeth carbide chip 36/80 grit carbide chip 36/80 grit diamond chip 40/60 grit diamond chip 40/60 grit 3/32 x 1/16 3/32 x 1/16 7/32 x 1/16 7/16 x 1/16 7/16 x 1/16 7/16 x 1/16 7/32 x 3/32 7/16 x 3/32 7/32 x 5/64 7/16 x 5/64 12,000 12,000 12,000 12,000 12,000 12,000 20,000 20,000 20,000 20,000 aluminum laminated plastics pressed board wood aluminum laminated plastics pressed board wood aluminum laminated plastics pressed board wood aluminum laminated plastics pressed board wood aluminum laminated plastics pressed board wood aluminum laminated plastics pressed board wood fiberglass rubber fiberglass rubber fiberglass rubber fiberglass rubber saw blades ­ dotco oscillating saws with 3/8 arbor hole 14-1740 14-1741 14-1742 14-1746 14-1743 14-1744 14-1745 14-1747 2 2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 3 carbide chip 36/80 grit diamond chip 40/60 grit stainless steel 124 teeth flush stainless 124 teeth carbide 120 teeth razor stainless steel 120 teeth razor 7/16 x 3/32 7/16 x 5/64 9/16 x 3/64 9/16 x 3/64 9/16 x 1/16 9/16 x 3/64 9/16 x 3/64 9/16 x 3/64 fiberglass fiberglass carbon composites wood uncured or cured composites aluminum plastic wood uncured or cured composites aluminum plastic cured graphic composites cardboard light plastic confined space cardboard light plastic use only for sawing non-metallic materials caution use only for sawing non-metallic materials part number diameter type maximum depth of cut use with model recommended use up to guidelines only saw blades ­ 7/16 arbor hole 14-2147 14-2146 14-2928 14-2929 14-1887 14-1888 14-1889 2 1/2 2 1/2 3 3/8 3 3/8 2 2 2 high speed steel 44 teeth high speed steel 80 teeth high speed steel 60 teeth high speed steel 80 teeth high speed steel 22 teeth high speed steel 44 teeth high speed steel 60 teeth 9/16 9/16 15/16 15/16 7/16 x 1/16 7/16 x 1/16 7/16 x 1/16 12s2794-01 12s2793-01 12s2794-02 12s2792-02 12s1288-04 12s1288-04 12s1288-04 1/4 aluminum 1/2 plywood 1/2 phenolic 16 gauge steel 1/4 aluminum 1/2 plywood 1/2 phenolic 20 gauge steel paneling plywood aluminum laminated plastics pressed board wood aluminum laminated plastics pressed board wood aluminum laminated plastics pressed board wood part number diameter type maximum depth width of cut recommended use guidelines only saw blades ­ 3/4 arbor hole 14-2701 14-2694 14-2697 14-2699 14-2700 14-2710 14-2711 14-2690 4 4 4 4 4 4 4 4 carbide chip 36/80 grit carbide chip 36 grit carbide chip 80 grit carbide tip 20 teeth carbide tip 20 teeth carbide tip 20 teeth carbide tip 12 teeth diamond chip 60/80 grit 1 x 1/8 1 x 11/64 1 x 1/8 1 x 7/64 1 x 7/64 1 x 7/64 1 x 7/64 1 x 5/64 fiberglass hard rubber hard rubber fiberglass thin fiberglass plastic laminates to 1/8 thick thicker fiberglass plastic laminates to 1/2 thick thin non-ferrous material to approx 1/8 thick thicker non-ferrous material to approx 1/2 thick fiberglass vacuum conversion kits dotco 12-27 series to convert an existing dotco front exhaust series 12-27 saw to vacuum operation order any of the conversion kits listed in the table refer to the vacuum ready models listed on page 101 as a guideline to selection note when converting to vacuum free speed of the tool will be reduced 20 part number converts front exhaust to this configuration dotco 12-42 series to convert an existing dotco front exhaust series 12-42 saw to vacuum operation order any of the conversion kits listed in the table refer to the vacuum ready models listed on page 102 as a guideline to selection note when converting to vacuum free speed of the tool will be reduced 20 part number converts front exhaust to this configuration caution these carbide chip and tip and diamond blades are not to be used on metallic materials slim blade for easy cutting of fiberglass with minimum dust -36 grit on periphery and 80 grit on the sides 2704 2705 2729 option 1 ­ porta bag option 2 ­ floor bag option 3 ­ vacuum system adapter 4131 4132 4133 option 1 ­ porta bag option 2 ­ floor bag option 3 ­ vacuum system adapter 56 warning face eye protection must be worn while operating power tools per ansi b186.1 cutting tool maximum speed rating must equal or exceed speed of air tool 90psi 620 kpa follow cutting tool manufacturer s mounting operating instructions tools must be equipped with lock-off lever to be ce compliant warning face eye protection must be worn while operating power tools per ansi b186.1 cutting tool maximum speed rating must equal or exceed speed of air tool 90psi 620 kpa follow cutting tool manufacturer s mounting operating instructions tools must be equipped with lock-off lever to be ce compliant 57

[close]