Page 29 of Tools & Equipment 2008 by Custom Chrome

index apparel cam locking tool permits the technician to lock the camshaft and crankshaft sprockets to properly remove replace and torque the sprocket bolts this tool is made from non-marring delrin fits all 2007 big twins and 2006 thru 2007 dyna glide models 622030 sold each $64.99 primary chain locking tool use to lock the clutch hub sprocket to the front engine sprocket with the two sprockets locked together engine and clutch nuts can easily be removed and retorqued 622035 fits all 2007 big twins and 2006 thru 2007 dyna glide models $44.99 seats bags foot controls hand controls inner cam bearing removal tool used to easily remove the inner cam bearing insert puller collet into the cam bearing i.d insert dowel pin place remover body over collet lube threads and with hand tools the bearing is pulled from case this precision tool will also keep all pin bearings from falling into the engine case 622032 fits all 2007 big twins and 2006 thru 2007 dyna glide models $219.99 lighting electrical case splitter tool main drive gear installation tool use this tool to safely install a new or newly repaired main drive gear this job can be performed with the transmission still in the frame with hand tools this tool will hold the main drive gear square to its bearing bore eliminating any marring of the gear or bearings 622031 fits all 2007 big twins and 2006 thru 2007 dyna glide models $275.99 use this tool to break the case sealant by pushing apart both case halves bolt with supplied hardware this tool to the primary mounting holes hand thread-in pushing screw and the flywheels will be pushed from the left case 622033 fits all 2007 big twins and 2006 thru 2007 dyna glide models $249.99 exhaust intake transmission main drive gear tool use to remove the large 21/4 hex nut from the end of main drive gear which secures the rear drive trans pulley just thread the inner support collar to end of mainshaft place the socket over the collar with a 1/2 drive tool and unthread right hand thread the locknut 622037 fits all 2007 big twins and 2006 thru 2007 dyna glide models $154.99 engine main drive gear bearing and seal installation tool use this tool to safely install new main drive gear bearings and seal with use of a small 1-ton press this tool will hold bearings and seal square to its bore eliminating any marring of the bearings and seals and installing both to the right depth 622042 fits all 2007 big twins and 2006 thru 2007 dyna glide models $94.99 gaskets tranny clutch main bearing installation tool used to safely install a new main transmission case bearing with hand tools it holds the bearing square to its bore eliminating any marring of the bearing bore 622034 fits all 2007 big twins and 2006 thru 2007 dyna glide models $174.99 driveline transmission door removal tool use this tool to remove pull the complete door with gears and shafts from the transmission just prepare the trans for disassembly bolt this tool to the outside of door and place the two supplied press pins into the two screw holes of trans case thread in two of the screws securing the door to cases and the door is pulled from case 622036 fits all 2007 big twins and 2006 thru 2007 dyna glide models $139.99 wheels tires brakes frames shift fork shaft tool use this tool to loosen and remove both shifter shafts from transmission door allowing further disassembly of the transmission 622041 fits all 2007 big twins and 2006 thru 2007 dyna glide models $16.99 forks shocks sheetmetal inner cam bearing installer use this tool to press in the two inner cam bearings designed to press from letter side of the inner cam bearings by putting all the pushing pressure to the very outer wall of bearing shell eliminating damage to the bearings cam and cases this tool will stop at the case and set the bearing depth to .023 to .028 below the case surface use with cc #622032 622038 fits all 2007 big twins and 2006 thru 2007 dyna glide models $184.99 valve spring compressor tool use this collar with cc #20696 to remove and replace valves and conical beehive springs a must-have tool for safe valve work 622039 fits all big twin models 2005 thru 2007 and sportsterŽ and buellŽ models 2004 thru 2007 except se and v-rodŽ $74.99 gauges cam assembly tool use to hold both cams in an upright position while lowering the cam support plate over both guides this tool has a non-marring material that will not damage any of the cam s surfaces 622040 fits all 2007 big twins and 2006 thru 2007 dyna glide models $149.99 chemicals general cross reference

[close]