Page 7 of Complete Line of Press Fit Fasteners by Driv-Lok, Inc.

20 Ordering Information STANDARD AND SPECIAL OPTIONS The table below indicates various characteristics which are standard or available as options. If you do not see the option you desire, call DRIV-LOKs Sales Department for assistance. KEY: A Available on special orders E Engineering evaluation required NA Not Available S Standard S/A Standard or Available depending upon diameter length, or material (inquire for specific details). Options Fastener Type Grooved Pins Grooved Studs Lok- Dowels Vent Dowels Knurled Pins Spring Pins BARB-LOK Studs BARB-LOK Pins Square Keys Rectangular Keys SHEAR- PROOF Pins Dimensions* Nominal Diameter/Width S S S S A A S S A S A Expanded Diameter S S S S NA A S S A A A Pin/Shank Length S S S S A A S S A S A Groove Length S S S S A NA NA NA NA A A Groove Location S S S S A NA NA NA NA A A Knurl Length NA NA NA NA NA A NA NA NA NA NA Knurl Location NA NA NA NA NA A NA NA NA NA NA Barb Location NA NA NA NA NA NA S A NA NA Characteristics Groove Type A S NA S A NA NA NA NA NA NA NA A3 A NA A A NA NA NA NA NA NA NA B A NA A A NA NA NA NA NA NA NA C S NA A A NA NA NA NA NA NA NA D A NA A A NA NA NA NA NA NA NA E S NA A A NA NA NA NA NA NA NA G S NA A A NA NA NA NA NA NA NA H S NA A A NA NA NA NA NA NA NA U S NA A A NA NA NA NA NA NA NA Other Special E E E S NA NA NA NA NA A A Groove Configuration Diamond S/A A A A NA NA NA NA NA E E Oval S/A NA A A NA NA NA NA NA S A Square S/A S A S NA NA NA NA NA E E Tapered S/A A S A NA NA NA NA NA E E Material 1000 Series Steel A S NA A A A S S A A A Low Carbon S NA NA S A A NA NA A A E 12L14 A NA NA A A A NA NA A S E 4140/6150 A NA S A A A NA NA NA A E 300 Series Stainless A A NA A A A A NA NA E E 400 Series Stainless A A NA A A A S NA NA E E Aluminum A A NA A E A NA A A A E Brass E E NA E E E NA E E NA NA Bronze E E NA E E E NA E E NA NA Beryllium Copper NA NA NA NA NA NA A NA NA NA NA End Configurations Chamfered S/A S S S A A S S A S NA Crowned S/A E A A A A NA E A NA NA Radiused A E A A A A NA E A E E Square Cut S/A A A A A A NA A A S A Spherical E E E E E E NA E E NA NA Combination E NA E E E E NA NA E E NA Finishes Zinc S S A A E A S S A A A Phosphate A A A A E A A A A A A Nickel A A A A E A A A A A A Black Oxide A A A A E A A A A A A Plain A A A A A A A A A A A Light Oil A A S S A A S A A S A Wax A A A A E A A A A A A Passivated (SS Only) A A NA A E A S A NA A A Other E E E E E E E E E E E Head Type Round NA S NA NA NA NA NA S NA NA NA Flat NA A NA NA NA NA NA A NA NA NA T NA A NA NA NA NA NA A NA NA NA Special NA E NA NA NA NA NA E NA NA NA Heat Treatment Unhardened S S NA A A A A S A S A Through Hardened A A S A A A S NA NA A A Case Hardened A A NA S A A NA E NA A A *See table of pin desired for specific standard dimensions available. Not all standard items are stocked. Call DRIV-LOKs Sales Department for availability. DRIV-LOK, Inc. 5 Grooved Pins (cont.) CHECKING EXPANDED DIAMETERS As shown, expanded diameters cannot be accurately measured using a micrometer. For accurate measurement of expanded diameters, a ring gage must be used. (Grooved Pins continued on page 6) Exp. Diam. Nom. (Dx) Diam. reduced (D) by 1/16 .002 3/32 .002 1/8 .002 5/32 .002 3/16 .003 7/32 .003 1/4 .003 5/16 .004 3/8 .005 7/16 .006 1/2 .006 TOLERANCES: On Nominal Diameter D : +.000/-.0015 up to 7/64" diameter +.000/-.002 7/64" diameters and over On overall Length L : .010 for all diameters For stainless steels and other special materials, the expanded diameters shown in above table are reduced by amounts shown at left. Note: Intermediate pin lengths, pin diameters up to 3/4", groove lengths, and special groove positions are ordered as specials. See pages 20 and 21 for ordering information. STANDARD GROOVED PIN DIMENSIONS Nominal Diameters Dimension 1/16 3/32 1/8 5/32 3/16 7/32 1/4 5/16 3/8 7/16 1/2 Nominal Diameter Max. .0625 .0938 .1250 .1563 .1875 .2188 .2500 .3125 .3750 .4375 .5000 Min. .0610 .0923 .1230 .1543 .1855 .2168 .2480 .3105 .3730 .4355 .4980 Crown Height E .0065 .0091 .0130 .0170 .0180 .0220 .0260 .0340 .0390 .0470 .0520 Crown Radius R .010 5/64 1/8 5/32 3/16 1/4 9/32 5/16 3/8 15/32 17/32 5/8 Pilot Length P (Ref.) 1/32 1/32 1/32 1/16 1/16 1/16 1/16 3/32 3/32 3/32 3/32 Chamfer Length C min. .005 .005 .005 .005 .016 .016 .016 .031 .031 .031 .031 Chamfer Angle A 5 35 35 35 35 35 35 35 35 35 35 35 Neck Radius M (Ref.) 1/64 1/32 1/32 1/32 3/64 3/64 1/16 1/16 3/32 3/32 Neck Width G .005 .033 .064 .064 .064 .096 .096 .127 .127 .190 .190 Neck Diameter K .005 .062 .083 .104 .125 .146 .167 .209 .250 .293 .312 Shoulder Width S +.010/-.000 1/32 1/32 3/64 3/64 1/16 1/16 3/32 1/8 1/8 1/8 1/4 1/4 1/4 3/8 3/8 1/2 1/2 5/8 3/4 7/8 1 Lengths* L .010 to to to to to to to to to to to 1 1 1/4 1 1/2 2 2 2 1/4 2 3/4 2 3/4 3 1/2 3 1/2 3 1/2 * Length increments are by 1/8 inch up to 1 inch, and by 1/4 inch over 1 inch. Standard availability may vary depending upon groove type. The length of chamfered pins is measured overall from end to end. The overall length of crowned pins is measured at L 2E. End configuration may vary depending upon pin length and groove type. All dimensions apply prior to plating. STANDARD EXPANDED DIAMETERS (Dx) Nominal Diameter 1/16 3/32 1/8 5/32 3/16 7/32 1/4 5/16 3/8 7/16 1/2 Expanded Diameter .0015 .002 .0025 .003 1/8 .068 .101 .134 .166 .198 .230 .263 .329 3/16 .068 .101 .134 .166 .198 .230 .263 .329 1/4 .068 .101 .134 .166 .198 .230 .263 .329 5/16 .068 .101 .134 .166 .198 .230 .263 .329 .394 .459 .525 3/8 .068 .101 .134 .166 .198 .230 .263 .329 .394 .459 .525 7/16 .068 .101 .134 .166 .198 .230 .263 .329 .394 .459 .525 1/2 .068 .101 .134 .166 .198 .230 .263 .329 .394 .459 .525 9/16 .068 .101 .134 .166 .198 .230 .263 .329 .394 .459 .525 5/8 .068 .101 .134 .166 .198 .230 .263 .329 .394 .459 .525 3/4 .067 .100 .134 .166 .198 .230 .263 .329 .394 .459 .525 7/8 .067 .100 .133 .165 .198 .230 .263 .329 .394 .459 .525 1 .067 .100 .133 .165 .198 .230 .263 .329 .394 .459 .525 1 1/4 .100 .132 .164 .197 .230 .263 .329 .394 .459 .525 1 1/2 .132 .164 .197 .229 .262 .329 .394 .459 .525 1 3/4 .163 .197 .229 .262 .328 .393 .459 .525 2 .163 .196 .229 .262 .328 .393 .458 .525 2 1/4 .229 .262 .328 .393 .458 .524 2 1/2 .261 .327 .393 .458 .524 2 3/4 .261 .327 .393 .458 .524 3 .392 .457 .523 3 1/4 .392 .457 .523 3 1/2 .391 .456 .522 Length "Expanded Diameter" "Nominal Diameter" Holding The Future Together

[close]