Catalog: Complete Line of Press Fit Fasteners | |
| the industry in carrying a full line of press fit fasteners for over 60 years. 3 Driv ... -6 DRIV-LOK , Inc. A Complete Line of Press Fit Fasteners Metric sizes also ... | |
| to produce a wide range of special press fit fastening and joining products to ... are a small sampling of these Special Press Fit Fasteners NOTES ... | |
| DRIV-LOK, Inc. 1 broad capabilities. If you do not see the type of fastener to meet your requirements, please send a sketch of the fastener or a description of the application to the DRIV- LOK Sales Department Phone: 815/895-8161 Fax: 815/895-6909 Website: www.driv-lok.com Email: driv-lok@driv-lok.com Fasteners shown at actual size 4 squares 1" SKETCH PART CONCEPT WITH TOLERANCES | |
| solutions for our customers who need press fit fastening, joining and special ... 60 YEARS OF SOLUTION RESOLUTION IN THE PRESS FIT FASTENER INDUSTRY Whatever we call ... the general category of manufacturer of press fit fastening and joining products. ... Manufacturing customer solutions is the press fit fastener market is our forte. The ... in being a high quality manufacturer of press-fit fasteners, we stay focused on doing ... | |
| this Comprehensive Guide to DRIV-LOKs press fit fastening and joining products ... dont find the answer to your specific press fit fastening and joining products ... applications. 3. Driv-Lok standard press fit fasteners are manufactured to ASME ... | |
| Grooved pins are non-threaded press fit fasteners. A PRESS FIT fastener is a ... fastener which is PRESSED into an appropriate size hole which ... will provide the proper interference FIT to lock the fastener in place. Grooved ... pins differ from many conventional press fit fasteners, such as dowel pins, in ... economic advantage over other types of press fit fasteners. Grooved pins are ... as a pivot, stop or hinge pin. When pressed in place, the grooved portion locks in ... | |
| 20 Ordering Information STANDARD AND SPECIAL OPTIONS The table below indicates various characteristics which are standard or available as options. If you do not see the option you desire, call DRIV-LOKs Sales Department for assistance. KEY: A Available on special orders E Engineering evaluation required NA Not Available S Standard S/A Standard or Available depending upon diameter length, or material (inquire for specific details). Options Fastener Type Grooved Pins Grooved Studs Lok- Dowels Vent Dowels Knurled Pins Spring Pins BARB-LOK Studs BARB-LOK Pins Square Keys Rectangular Keys SHEAR- PROOF ... | |
| should be considered when designing press fit fasteners for your application. ... used as a hinge or pivot pin. Driven or pressed into a straight drilled hole, the ... | |
| C SHEAR- PROOF is a special pin. High Pressure Piston and Rod Assembly Type B Pin was ... . This pin is easily installed, fits flush and permits plating before ... | |
| resistance. FUNCTION Lok-Dowels are pressed or driven into a drilled and reamed ... undersize Ream full size Drive or press LOK DOWELS into place LOK DOWELS lock ... | |
| power is required. Machine keys are pressed into keyways which are cut into a shaft ... engages a standard keyway, a moderate press fit results. The displaced material is ... on two opposite surfaces to provide a press fit in both shaft and gear or pulley ... need for screws or time-consuming hand fitting normally needed for retaining key in ... | |
| Keys APPLICATION Machine keys are pressed into keyways which are cut into a shaft ... | |
| the entire pin circumference when it is pressed into a hole. The insertion, holding, ... | |
| DRIV-LOK, Inc. 13 Coiled Pins CARBON STEEL AND OTHER MATERIALS AVAILABLE ASME B18.8.2-1995 Slotted Coiled Spring Pins (cont.) SPRING PIN STANDARD DIMENSIONS A C RECOMMENDED HOLE SIZE MINIMUM DOUBLE SHEAR STRENGTH POUNDS Carbon Steel and 420 Stainless Steel Min. Max. B Max STOCK THICK- NESS Nominal Maximum (Go Ring Gage) Minimum 1/3 (D1+D2+D3) Min. Max. 1/16 (.062) .066 .069 .059 .007 .028 .015 .063 .065 430 5/64 (.078) .083 .086 .075 .008 .032 .018 .079 .081 800 3/32 (.094) .099 .103 .091 .008 .038 .022 .095 .097 1,150 1/8 (.125) .131 .135 .122 .008 .044 ... | |
