Catalog: GM Goodwrench Engines Catalog | |
| August 2004 GOODWRENCH REMANUFACTURED ENGINES COMPONENT SUMMARY LIST cont. ... finish and geometry as OE varies by engine family. Deck Height Same to .010" ... .030" undersize (Dia) varies by engine family same surface finish and geometry ... center distance to OE specification. *Assembly information -OE bearing clearances are ... | |
| most important items in installing an engine. It is important to rid the system of ... contaminants to ensure that the new engine has the proper heat transfer taking ... place. Otherwise, the engine will over heat and cause considerable ... working order, the chance of repeat engine failure is significantly reduced. If ... the old engine is still running, flush the cooling ... system before removing the old engine. If the engine is not running, be sure ... after replacing it with the new engine. Refer to the service manual for the ... of the steps involved in installing an engine. They give a general overview of the ... transferable components from the old engine should be placed on the new engine. To ... begin, mount the engine on an engine stand with the oil pan facing upwards, ... | |
| PROCEDURES cont. 8. Rotate the engine on the engine stand so that the intake ... and camshaft. 10. Pre-lube the engine with A.P.I. Starburst certified motor ... oil. Pre-lubing the engine is necessary to avoid dry start damage ... The most efficient way to pre-lube the engine is to use the J-45299 engine pre-luber ... on all applications. However, if no engine pre-luber is available and the engine ... has a mechanical distributor, the engine can be pre-lubed by priming the oil ... after pressure builds up in the engine. This is to flush any debris from the ... engine without a load on the bearings while ... seal properly to avoid damage to the engine. Refer to the service manual for that ... that were removed from the original engine Engine mounts (engine to frame) ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 52 August 2004 ... , Oldsmobile S1 (LN8)(2.5E) GMC Engine-Specific Content: Front Cover and Oil Pan Notes ... balancer separately, not included in assembly components. INSTALLATION INSTRUCTIONS ... The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 67 August 2004 ... , GMC ST1 (LL2)(2.8R)(2.8S) A. Trans Engine-Specific Content: Oil Pan, Valve Covers, ... Only INSTALLATION INSTRUCTIONS This engine incorporates a 'balanced'automatic ... with part number 14097667. This engine is built with 1992 production parts. ... , use 1992 parts. Covers from replaced engine may have to be used. On "F" cars and " ... 10078999, B) remove oil pump screen assembly and replace with part number 10118624, ... ) use oil level indicator from replaced engine. This engine is built to production ... , GMC S1 (LL2)(2.8R), M. Trans (ML3) Engine-Specific Content: Oil Pan, Valve Covers, ... Only INSTALLATION INSTRUCTIONS This engine incorporates a 'balanced'flywheel, part ... replace with part number 14100559. This engine is built with 1992 production parts. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 68 August 2004 ... 1997 Chevrolet, Oldsmobile N (L82) Engine-Specific Content: Front Cover, Oil Pan, Oil ... Level Sensor, Lower Intake Manifold, Engine Oil and Additive Replaces: Replaced ... -99 Chevrolet, Oldsmobile N (L82) Engine-Specific Content: Front Cover, Oil Pan, Oil ... Level Sensor, Lower Intake Manifold, Engine Oil and Additive Replaces: Replaced ... Oldsmobile U Van (LG6)(3.1D) MD9, C67 Engine-Specific Content: Front Cover and Pointer, Lower ... , Pontiac U (LG6)(3.1D) Oldsmobile Engine-Specific Content: Front Cover, Lower Intake ... Covers INSTALLATION INSTRUCTIONS This engine incorporates 1993 production parts. ... components and the dipstick and tube assembly, use 1993 LG6 service parts. The engine ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 69 August 2004 ... W19 Type 1 VIN 400001 thru 800000 Engine-Specific Content: Front Cover, Lower Intake ... , Oil Pan, and Valve Covers Notes: If engine is received without dampener, must ... . INSTALLATION INSTRUCTIONS This engine incorporates 1993 production parts. ... components and the dipstick and tube assembly, use 1993 LH0 service parts. The engine ... Chevrolet W (LH0)(3.1T) M13, NB2, NA5 Engine-Specific Content: Front Cover, Lower Intake ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 74 August 2004 ... M27 1991-92 Oldsmobile W (LQ1) M27 Engine-Specific Content: Crankshaft Balancer, Flywheel ... Assembly, Oil Pan, Oil Level Indicator and Tube, ... U (LA1) NF7 2002 Buick B (LA1) NF7 Engine-Specific Content: Front Cover, Oil Pan, and ... exc. KC4) 2002 Pontiac U (LA1) NT3 Engine-Specific Content: Front Cover, Oil Pan, and ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 77 August 2004 ... W (LX5)(3.5H) MFI DOHC (NF2) Engine-Specific Content: Crankshaft Balancer Assembly, ... Sensors, Camshaft Covers, Front Cover Assembly, Filter, Level Indicator Assembly, Oil ... SW, Oil Pan, Flywheel, Spark Plugs, Engine Oil Additive, Water Pump/Pulley ... Assembly, Water Outlet, and Thermostat Notes: ... G (LX5)(3.5H) MFI DOHC (NC1) Engine-Specific Content: Balancer, Flywheel, Oil Pan, ... Oil Pump, and Oil Filter Notes: For engines with physical ID of KWA or KXA, reuse ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 88 August 2004 ... , GMC C1,2 G1,2 K1, M1 (LB1)(4.3N) Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 89 August 2004 ... 3Z) Exc. Emis. above 8500lb. GVW (NA4) Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 90 August 2004 ... 3Z) Exc. Emis. above 8500lb. GVW (NA4) Engine-Specific Content: Oil Pump Notes: Includes 21- ... PSI Oil Pressure Bypass Valve. Engine not used on GMC Typhoon and Syclone ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 91 August 2004 ... 1993 Chevrolet, GMC ST1 (LB4)(4.3Z) Engine-Specific Content: Oil Pump Notes: Includes 21- ... PSI Oil Pressure Bypass Valve. Engine not used on GMC Typhoon and Syclone ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 92 August 2004 ... 4.3L 1993 Chevrolet B (LB4)(4.3Z) Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... Chevrolet, GMC LM1, ST1 (L35)(4.3W) Engine-Specific Content: Oil Pump Notes: Includes 21- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 93 August 2004 ... Chevrolet, GMC LM1 (LB4)(4.3Z) M30 Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... Chevrolet, GMC G1,2 (LB4)(4.3Z), M30 Engine-Specific Content: Oil Pump Notes: Includes 21- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 94 August 2004 ... ST1 (06-16)(L35)(4.3W) M30 (exc. CTF) Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... Sys (under 8500lb. GVM) M30 (A/Trans) Engine-Specific Content: Oil Pump Notes: Includes 21- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 95 August 2004 ... ) 1995 Chevrolet, GMC LM1 (L35) M30 Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... , GMC G2,3 (L35) MTI, NA4, ZK3 Engine-Specific Content: Oil Pump Notes: Includes 21- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 96 August 2004 ... )(4.3A) Emis. above 8500lb. GVW (NA4) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Rocker Cover Notes: *Effective with engine codes ADF, AJZ, FLX, and XDF. ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 97 August 2004 ... , GMC G1,2 (L35) M30, NA1 (exc. ZK3) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... replacing a 1998 and prior Goodwrench engine (12532552), also use 1-12557587 ... flywheel when replacing a Goodwrench engine (12532552) for P3 application. ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 98 August 2004 ... 1996-2000 Chevrolet, GMC LM1 (L35) Engine-Specific Content: Oil Pan, Oil Filter, Front ... Notes: When replacing a 1998 and prior engine, also use 1-12557587 flywheel for A. ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 99 August 2004 ... -99 Chevrolet, GMC S1 (LF6) M30, M50 Engine-Specific Content: Oil Pan, Oil Filter, Front ... Notes: When replacing a 1998 and prior engine, also use 1-12557587 flywheel for A. ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 100 August 2004 ... Chevrolet, GMC G2,3 (L35)(4.3W) MT1 Engine-Specific Content: Harmonic Balancer, Balance ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... ) M30 2002 Chevrolet, GMC CK1 (LU3) Engine-Specific Content: Light Duty Shallow Oil Pan, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 101 August 2004 ... ) M30 2002 Chevrolet, GMC LM1 (LU3) Engine-Specific Content: Light Duty Deep Oil Pan, ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... Chevrolet, GMC S1 (LU3) M50, M30 Engine-Specific Content: Oil Pump, Front Cover, and ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 102 August 2004 ... , GMC G2,3 (L35) MT1, NA4 (exc. ZK3) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Notes: When replacing a 1998 prior GW engine (12369214), also use flywheel (12557584 ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 108 August 2004 ... 4.6-9) 1994 Cadillac K (L37)(4.6-9) Engine-Specific Content: Cam Crank Posn Sensors, ... 4.6L 1995-99 Cadillac K (L37)(4.6Y) Engine-Specific Content: Cam Crank Posn Sensors, ... Camshaft Covers, Crankshaft Balancer, Engine Oil Manifold, Front Cover, Flywheel, ... w/Adapter, Oil Level Indicator Tube Assembly, Oil Level Sensor, Oil Pan, Oil Pump ... 4.6L 1995-99 Cadillac K (LD8)(4.6Y) Engine-Specific Content: Cam Crank Posn Sensors, ... Camshaft Covers, Crankshaft Balancer, Engine Oil, Front Cover, Flywheel, Oil Fill ... 1995 models, install fresh PCV Tube Assembly, part number 12552458. Replaces: ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 109 August 2004 ... )(4.6Y) 1994 Cadillac K (LD8)(4.6Y) Engine-Specific Content: Cam Crank Posn Sensors, ... Housing, Water Pump w/Pulley, and Engine Oil Replaces: 12369569, 12529512 ... 4.6L 2000 Cadillac K (L37) Notes: Engine assembly is used with and without V03 ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 112 August 2004 ... .0H) 1991-92 Cadillac D (L03)(5.0H) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Cover INSTALLATION INSTRUCTIONS This engine is built with 1993 production ... components. When servicing engine, use 1993 service parts. For "D" and "F ... pan and replace with pan from replaced engine or order oil pan kit, part number ... W thread sealer, part number 12345493. Engine built after 04/13/94 have roller timing ... bolt part number 9417950 must be used. Engines built with link timing chain must use ... and bolt part number 3874878. This engine is built to production point of build ... -95 Chevrolet, GMC CK1,2 (L03)(5.0H) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... By: INSTALLATION INSTRUCTIONS This engine is built with 1993 production ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 115 August 2004 ... Chevrolet, GMC CK1(06) G1 (LS9)(350L) Engine-Specific Content: Front Cover, Oil Pan, and ... Goodwrench 5.7 Liter (350 C.I.D.) V8 engine is to be used on 1973 through 1985 ... and crankshaft before installing engine. Check engine restrictor at center of ... manifold side gaskets from replaced engine and procure one of the following units ... timing pointers are provided with this assembly. Determine and install correct pointer ... or install front cover assembly from replaced engine. Some models may ... opposite of dipstick location. This engine is built to production point of build ... .7L 1997-98 Chevrolet Y (LS1)(5.7G) Engine-Specific Content: Front Cover, Harmonic Balancer ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 117 August 2004 ... (L05)(5.7K) MT1, 9C2, 5Z1 (exc. NM8) Engine-Specific Content: Front Cover, Oil Pan, ... 12520270 5.7 Goodwrench 5.7 Liter engine is built with 1993 model year designed ... bead), oil pan gasket, and oil pump assembly. When servicing this engine, it is ... be of the same type and design. This engine is built with current-production valve ... be necessary to use cover from replaced engine. On models with a 5-Quart Oil Pan, ... remove oil pan and oil pump assembly. Replace with original or new oil pan ... assembly part number 12518043, oil pump assembly part number 10168529, and screen oil ... part number 10166159. This engine is built to production point of build ... Chevrolet, GMC G1,2 (L31)(5.7R) M30 Engine-Specific Content: Crankshaft Hub, Front Cover, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 124 August 2004 ... INSTRUCTIONS This Chevrolet Mark IV engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts ... , and valve covers to the replacement engine. Thoroughly clean all old parts to avoid ... install the sensor on the replacement engine. Use a thread sealer to prevent coolant ... with shallow oil pan, a new oil pump assembly, part number 14067529, with shorter pick ... in place of the pump supplied with this engine. Attach two Goodwrench engine decals ( ... covers. CAUTION: The oil pump in this engine must be primed before starting the ... engine. Refer to vehicle service chassis manual ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 129 August 2004 ... INSTRUCTIONS This Chevrolet Mark IV engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Part and ... and valve covers to the replacement engine. Thoroughly clean all old parts to avoid ... install the sensor on the replacement engine. Use a thread sealer to prevent coolant ... with shallow oil pan, a new oil pump assembly, part number 14067529, with shorter ... in place of the pump supplied with this engine. Attach two Goodwrench engine decals ( ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Use 6 ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 130 August 2004 ... number 12532427, Goodwrench 7.0 Liter engine assembly, has been developed as a ... service replacement engine for 1986-1994 medium duty truck 427 C. ... I.D. engine applications. NOTICE: When using this ... engine to replace 1990 and prior applications ... ,7 1990 427 LR0 VIN "H" NOTICE: This engine comes equipped with an 8" front damper ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 131 August 2004 ... trucks originally manufactured with 454 engines with the following restrictions: ... Remanufactured engine may be 2 or 4 bolt design. Not ... in place of the pump supplied with the engine. 1990 production engines use ESC knock ... sensor. Remanufactured engines must be modified for use on 1990 ... -seal pipe thread sealer for ESC sensor assembly. 12353125 454 CID Reman 7.4L 1982-86 ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 132 August 2004 ... 1988-93 Chevrolet, GMC G3 (L19)-454N Engine-Specific Content: Crankshaft Balancer, Front ... number 88890529, Goodwrench 7.4 Liter engine assembly, has been developed as a ... service replacement engine for 1974-1993 light duty truck 454 C.I ... .D. engine applications. When using this engine to ... part number 3053355 is required. This engine is built to production point of build ... | |
