Catalog: GM Goodwrench Engines Catalog | |
| surfaces on new and remanufactured engines and/or cleaning parts from the failed ... engine to be reused, the use of surface ... TM, ABRASIVE DISCS) If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler must be replaced. If the ... to perform these repairs will void your Goodwrench Engine Warranty. Before installing any ... engine, verify that you have the correct engine ... appropriate Vehicle Chassis Service manual for proper repair procedures and ... , air purge and fluid volumes). Some engines have been remanufactured subsequent to ... service information (i.e., 1989 engines may incorporate design features ... If future service is necessary for the engine, consult the GM Parts Catalog, GM Part ... | |
| III Page 9 August 2004 TRANSFERABLE ENGINE COMPONENTS Take out the old engine, ... mount it on an engine stand, and carefully remove those ... that are to be transferred to the new engine. The following list of components should ... or were the cause of the original engine failure, they should be replaced. ... thoroughly before placing it on the new engine. Any foreign objects within the intake ... , heads and other vital parts of the engine. Warning Do not use any form of blasting ... cracks are found, replace the plate. On manual transmission vehicles, the crankshaft ... | |
| Page 11 August 2004 NON-TRANSFERABLE ENGINE COMPONENTS Some components off the old ... engine will not be able to be used on the new ... replacement engine. This is because they will hinder the ... performance of the engine if they are not replaced. Or, they are ... previously used in the original engine may be clogged or is worn out. The ... replaced prior to installing the new engine. Oil Pump, Pick-up Tube and Screen These ... components come with the new engine. PCV Valve and Crankcase Breather Filter ... that the emission standards of the engine are met and to prevent sludge, caused ... proper heat range for the vehicle and engine application. Failure to change the ... a choke and affect fuel consumption and engine performance. Cooling System Sealing ... prevent shaft seal damage. Fuel Filter Engine Oil Antifreeze Coolant Engine Oil ... | |
| most important items in installing an engine. It is important to rid the system of ... contaminants to ensure that the new engine has the proper heat transfer taking ... place. Otherwise, the engine will over heat and cause considerable ... working order, the chance of repeat engine failure is significantly reduced. If ... the old engine is still running, flush the cooling ... system before removing the old engine. If the engine is not running, be sure ... after replacing it with the new engine. Refer to the service manual for the ... of the steps involved in installing an engine. They give a general overview of the ... transferable components from the old engine should be placed on the new engine. To ... begin, mount the engine on an engine stand with the oil pan facing upwards, ... | |
| PROCEDURES cont. 8. Rotate the engine on the engine stand so that the intake ... and camshaft. 10. Pre-lube the engine with A.P.I. Starburst certified motor ... oil. Pre-lubing the engine is necessary to avoid dry start damage ... The most efficient way to pre-lube the engine is to use the J-45299 engine pre-luber ... on all applications. However, if no engine pre-luber is available and the engine ... has a mechanical distributor, the engine can be pre-lubed by priming the oil ... after pressure builds up in the engine. This is to flush any debris from the ... engine without a load on the bearings while ... proper sequence. Refer to the service manual for that vehicle and application for ... seal properly to avoid damage to the engine. Refer to the service manual for that ... | |
| levels and conditions of the following: Engine Oil Check for factory recommended ... pressure (see manual). Verify oil level is at manufaturer's ... recommended amount. Engine Coolant Make sure the thermostat is ... , if necessary. Refer to service manual for further details. Transmission ... Brake fluid Abnormal Noises With engine running, listen for noises such as: ... . Incorrect timing is a common cause of engine failure. Be sure the vehicle's timing ... label for specifications. Check the engine vacuum. Install a vacuum gage at the ... vacuum may indicate internal engine concerns. Other items: Cylinder heads ... | |
| 2004 INSTALLATION PROCEDURES cont. Engine Break-In Once the engine has been ... the oil pump has been primed, start the engine and let it idle at 1600 to 2000 RPM ... to stabilize. Refer to the service manual for the proper pressure range. During ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 33 August 2004 ... N (L61) 2004-05 Chevrolet N (L61) Engine-Specific Content: Oil Pan, Front Cover, and ... By: Notes: If using on vehicle with manual transmission, transfer flywheel from ... existing engine. For 2003 MY, fuel rail/injectors must ... 3Z (L61) 2005 Chevrolet 3A (L61) Engine-Specific Content: Oil Pan and Front Cover ... By: Notes: If using on vehicle with manual transmission, transfer flywheel from ... existing engine. INSTALLATION INSTRUCTIONS No special ... Chevrolet, Pontiac J (LN2)(2.2-4) MFI Engine-Specific Content: Front Cover, Spark Plugs, and ... instructions are included with the engine. 88894189 134 CID New 2.2L 1998 ... Chevrolet, Pontiac J (LN2)(2.2-4) MFI Engine-Specific Content: Oil Pan, Front Cover, Spark ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 35 August 2004 ... 2.3A) 1990 Oldsmobile W (LG0)(2.3A) Engine-Specific Content: Camshaft Housing, Front Cover ... Pump INSTALLATION INSTRUCTIONS This engine has been remanufactured subsequent to ... service information (i.e., 1989 engines by incorporate design features normally ... If future service is necessary for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... chassis service manual for proper repair procedures. After ... removing old engine, use new seals and gaskets and transfer ... tube and cap/indicator. Attach Quad IV engine decal (enclosed in instruction envelope ... ). Install replacement engine and add 4 quarts of Starburst certified ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 36 August 2004 ... Pontiac, Chevrolet N (LG0)(2.3A) Engine-Specific Content: Camshaft Housing, Front Cover ... Pump INSTALLATION INSTRUCTIONS This engine has been remanufactured subsequent to ... service information (i.e., 1989 engines by incorporate design features normally ... If future service is necessary for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... chassis service manual for proper repair procedures. After ... removing old engine, use new seals and gaskets and transfer ... tube and cap/indicator. Attach Quad IV engine decal (enclosed in instruction envelope ... ). Install replacement engine and add 4 quarts of Starburst certified ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 37 August 2004 ... , Oldsmobile, N (LD2)(2.3D) Buick Engine-Specific Content: Camshaft Housing, Front Cover ... Pump INSTALLATION INSTRUCTIONS This engine has been remanufactured subsequent to ... service information (i.e., 1989 engines by incorporate design features normally ... If future service is necessary for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... chassis service manual for proper repair procedures. After ... removing old engine, use new seals and gaskets and transfer ... tube and cap/indicator. Attach Quad IV engine decal (enclosed in instruction envelope ... ). Install replacement engine and add 4 quarts of Starburst certified ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 38 August 2004 ... Pontiac, Oldsmobile N (LD2)(2.3D) Engine-Specific Content: Camshaft Housing, Front Cover ... Pump INSTALLATION INSTRUCTIONS This engine has been remanufactured subsequent to ... service information (i.e., 1989 engines by incorporate design features normally ... If future service is necessary for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... chassis service manual for proper repair procedures. After ... removing old engine, use new seals and gaskets and transfer ... tube and cap/indicator. Attach Quad IV engine decal (enclosed in instruction envelope ... ). Install replacement engine and add 4 quarts of Starburst certified ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 42 August 2004 ... Buick 1990 Chevrolet W (LR8)(2.5R) Engine-Specific Content: Crankshaft Balancer, Front ... Cover INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 43 August 2004 ... Buick 1986 Chevrolet P (LR8)(2.5R) Engine-Specific Content: Crankshaft Balancer, Front ... Cover INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 44 August 2004 ... 1985 Chevrolet, Buick X (LR8)(2.5R) Engine-Specific Content: Crankshaft Balancer, Front ... Cover INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 45 August 2004 ... , Buick 1984 Pontiac P (LR8)(2.5R) Engine-Specific Content: Front Cover and Oil Pan ... INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 46 August 2004 ... A, X (LR8)(2.5R) Oldsmobile, Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 47 August 2004 ... , Oldsmobile N (L68)(2.5U) Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 48 August 2004 ... , Oldsmobile N (L68)(2.5U) Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 49 August 2004 ... N (L68)(2.5U) w/M.T. Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 50 August 2004 ... N (L68)(2.5U) w/A. Trans Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 51 August 2004 ... , Oldsmobile N (L68)(2.5U) Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 52 August 2004 ... CID Reman 2.5L 1989-90 Chevrolet, GMC M1, S1 (LN8)(2.5E) 1989-91 Chevrolet ... , GMC Z1 (LN8)(2.5E) 1991 Chevrolet, ... Oldsmobile S1 (LN8)(2.5E) GMC Engine-Specific Content: Front Cover and Oil Pan Notes ... . INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 53 August 2004 ... 151 CID Reman 2.5L 1988 Chevrolet, GMC M1, ST1, Z1 (LN8)(2.5E) Engine- ... Oil Pan INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 54 August 2004 ... 1986 Chevrolet M1, ST1 (LN8)(2.5E) Engine-Specific Content: Front Cover and Oil Pan ... INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 55 August 2004 ... 1985 Chevrolet M1, ST1 (LN8)(2.5E) Engine-Specific Content: Front Cover and Oil Pan ... INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 56 August 2004 ... , Buick 1988 Pontiac P (LR8)(2.5R) Engine-Specific Content: Front Cover INSTALLATION ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 57 August 2004 ... , Oldsmobile, N (L68)(2.5U) Buick Engine-Specific Content: Front Cover INSTALLATION ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 58 August 2004 ... 1991 Oldsmobile, Buick N (L68)(2.5U) Engine-Specific Content: Front Cover and Oil Pan ... INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 59 August 2004 ... Chevrolet, Oldsmobile, S1 (L38)(2.5A) GMC 1991-93 GMC Z1 (LLV)(L38)(2.5A) ... Engine-Specific Content: Front Cover and Oil Pan ... INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 60 August 2004 ... , A (LR8)(2.5R) Oldsmobile, Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTALLATION INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... service chassis manual for proper repair procedures and owner' ... s manual for capacities. Initially add 3 quarts ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 67 August 2004 ... LB8)(2.8S) A/Trans 1987-89 Chevrolet, GMC ST1 (LL2)(2.8R)(2.8S) A. Trans Engine ... Only INSTALLATION INSTRUCTIONS This engine incorporates a 'balanced'automatic ... with part number 14097667. This engine is built with 1992 production parts. ... , use 1992 parts. Covers from replaced engine may have to be used. On "F" cars and " ... ) use oil level indicator from replaced engine. This engine is built to production ... )(2.8S), M. Trans 1987-90 Chevrolet, GMC ST1 (LL2), M. Trans 1991-93 ... Chevrolet, GMC S1 (LL2)(2.8R), M. Trans (ML3) Engine ... Flywheel, and Torsional Damper Notes: Manual Transmission Only INSTALLATION ... INSTRUCTIONS This engine incorporates a 'balanced'flywheel, part ... replace with part number 14100559. This engine is built with 1992 production parts. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 79 August 2004 ... )(3.8C) 1989 Pontiac H (LN3)(3.8C) Engine-Specific Content: Balance Shaft, Front Cover, ... , transfer oil filter adapter from old engine or order new. Engine does not include ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... applicable state laws or regulations. Goodwrench Decals: Attach two 3800-engine decals ( ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... Refer to vehicle service chassis manual for proper priming procedures. Also, ... check engine oil level before starting engine. Refer to owner's manual for proper oil ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 80 August 2004 ... , Oldsmobile H (LN3)(3.8C) Buick Engine-Specific Content: Crankshaft Balancer, Crank and ... Cam Posn Sensor, Engine Coolant Temp Sensor, Front Cover, Int ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... applicable state laws or regulations. Goodwrench Decals: Attach two 3800-engine decals ( ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... Refer to vehicle service chassis manual for proper priming procedures. Also, ... check engine oil level before starting engine. Refer to owner's manual for proper oil ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 81 August 2004 ... Pontiac, Oldsmobile, H (L27) Buick Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... applicable state laws or regulations. Goodwrench Decals: Attach two 3800-engine decals ( ... the oil filter adapter from the old engine or use new part number 25537239. ... CAUTION: The oil pump in this engine must be primed before starting engine. ... Refer to vehicle service chassis manual for proper priming procedures. Also, ... check engine oil level before starting engine. Refer to owner's manual for proper oil ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 82 August 2004 ... , U Van (L27)(3.8L) Oldsmobile Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... applicable state laws or regulations. Goodwrench Decals: Attach two 3800-engine decals ( ... the oil filter adapter from the old engine or use new part number 24501300 and ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... Refer to vehicle service chassis manual for proper priming procedures. Also, ... check engine oil level before starting engine. Refer to owner's manual for proper oil ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 83 August 2004 ... , U Van (L27)(3.8L) Oldsmobile Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... applicable state laws or regulations. Goodwrench Decals: Attach two 3800-engine decals ( ... the oil filter adapter from the old engine or use new part number 24501300 and ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... Refer to vehicle service chassis manual for proper priming procedures. Also, ... check engine oil level before starting engine. Refer to owner's manual for proper oil ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 84 August 2004 ... Buick C (L67) 1994 Pontiac H (L67) Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... applicable state laws or regulations. Goodwrench Decals: Attach two 3800-engine decals ( ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... Refer to vehicle service chassis manual for proper priming procedures. Also, ... check engine oil level before starting engine. Refer to owner's manual for proper oil ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 85 August 2004 ... 2000-04 Pontiac, Buick H (L36)(3.8K) Engine-Specific Content: Flywheel, Oil Pan, Lower ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... applicable state laws or regulations. Goodwrench Decals: Attach two 3800-engine decals ( ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... Refer to vehicle service chassis manual for proper priming procedures. Also, ... check engine oil level before starting engine. Refer to owner's manual for proper oil ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... 2000-04 Buick C (L67)(3.8-1) SFI, SC Engine-Specific Content: Balancer, Flywheel, Oil Pan, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 86 August 2004 ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... applicable state laws or regulations. Goodwrench Decals: Attach two 3800-engine decals ( ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... Refer to vehicle service chassis manual for proper priming procedures. Also, ... check engine oil level before starting engine. Refer to owner's manual for proper oil ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... 1) 2004-05 Chevrolet W (L67)(3.8-1) Engine-Specific Content: Balancer, Crank Cam Posn. ... with new or Trans Original Sens. Engine comes with 97-00 Flywheel. Replaces: ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 87 August 2004 ... New 3.8L 2005 Chevrolet W (L26) Engine-Specific Content: Crank Balancer, Flywheel, Oil ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... applicable state laws or regulations. Goodwrench Decals: Attach two 3800-engine decals ( ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... Refer to vehicle service chassis manual for proper priming procedures. Also, ... check engine oil level before starting engine. Refer to owner's manual for proper oil ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 88 August 2004 ... G (LB4)(4.3Z) 1985 Chevrolet, GMC C1,2 G1,2 K1, M1 (LB1)(4.3N) Engine- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 89 August 2004 ... G (LB4)(4.3Z) 1987 Chevrolet, GMC CK1, R1,2, V1, RV1 (LB4)(4.3Z) 1987- ... 89 Chevrolet, GMC M1 (LB4) 1988 Chevrolet, GMC CK1,2, ... 3, V2 (LB4)(4.3Z) 1988-91 Chevrolet, GMC ST1 (LB4)(4.3Z) 1989-91 Chevrolet, ... GMC CK1,2 (LB4)(4.3Z) Exc. Emis. above ... 8500lb. GVW (NA4) 1987-90 Chevrolet, GMC G1,2,3 (LB4)(4.3Z) 1990 Chevrolet, ... GMC LM1 (LB4)(4.3Z) 1991 Chevrolet, GMC G1,2,3 (LB4)(4.3Z) Exc. Emis. above ... 8500lb. GVW (NA4) Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 90 August 2004 ... B (LB4)(4.3Z) 1992 Chevrolet, GMC CK1, ST1 (LB4)(4.3Z) 1992 Chevrolet ... , GMC CK2 (LB4) NA1 1992 Chevrolet, GMC LM1 (LB4) 1992 Chevrolet, GMC G1,2, ... 3Z) Exc. Emis. above 8500lb. GVW (NA4) Engine-Specific Content: Oil Pump Notes: Includes 21- ... PSI Oil Pressure Bypass Valve. Engine not used on GMC Typhoon and Syclone ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 91 August 2004 ... 262 CID Reman 4.3L 1993 Chevrolet, GMC ST1 (LB4)(4.3Z) Engine-Specific ... 21-PSI Oil Pressure Bypass Valve. Engine not used on GMC Typhoon and Syclone ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 92 August 2004 ... 4.3L 1993 Chevrolet B (LB4)(4.3Z) Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 93 August 2004 ... 262 CID Reman 4.3L 1994 Chevrolet, GMC CK1,2 (LB4)(4.3Z) 1994 Chevrolet, ... GMC ST1 (LB4)(4.3Z) MY2, M30 1994 ... Chevrolet, GMC LM1 (LB4)(4.3Z) M30 Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 94 August 2004 ... 262 CID Reman 4.3L 1994 Chevrolet, GMC LM1 (L35)(4.3W) M30 1994 Chevrolet ... )(L35)(4.3W) MY2, M30 1994 Chevrolet, GMC ST1 (06-16)(L35)(4.3W) M30 (exc. CTF ... ) Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 95 August 2004 ... 262 CID Reman 4.3L 1994 Chevrolet, GMC ST1 (L35)(4.3W) M30, CTF 1995 ... Chevrolet, GMC ST1 (L35)(4.3W) M50, M30, NM8 (exc. ... NM8) 1995 Chevrolet, GMC ST1 (L35)(4.3W) M50, NM8, W99 (exc. ... NM8) 1995 Chevrolet, GMC LM1 (L35) M30 Engine-Specific Content ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 96 August 2004 ... Heavy Duty 4.3L 1985-89 Chevrolet, GMC P4 Eng Dress Kit (LSA)* 1990-93 ... Chevrolet, GMC CK2, P3 (LB4)(4.3Z), Emis. above ... 8500lb. GVW (NA4) 1991-93 Chevrolet, GMC G3 (LB4)(4.3A) Emis. above 8500lb. GVW ... (NA4) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Rocker Cover Notes: *Effective with engine codes ADF, AJZ, FLX, and XDF. ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 97 August 2004 ... 262 CID New 4.3L 1996 Chevrolet, GMC P3 (L35)(4.3W) CPI, MT1* 1996-2000 ... Chevrolet, GMC CK1, S1 (L35) 1996-2000 Chevrolet, ... GMC G1,2 (L35) M30, NA1 (exc. ZK3) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Notes: When replacing a 1998 and prior Goodwrench engine (12532552), also use 1-12557587 ... with 12557584 flywheel when replacing a Goodwrench engine (12532552) for P3 application ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 98 August 2004 ... CID New 4.3L 1996-2000 Chevrolet, GMC, T1 (L35) Oldsmobile 1996-2000 ... Chevrolet, GMC LM1 (L35) Engine-Specific Content: Oil Pan, Oil Filter, Front ... Notes: When replacing a 1998 and prior engine, also use 1-12557587 flywheel for A. ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 99 August 2004 ... 262 CID New 4.3L 1996-99 Chevrolet, GMC S1 (LF6) M30, M50 Engine-Specific ... Notes: When replacing a 1998 and prior engine, also use 1-12557587 flywheel for A. ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 100 August 2004 ... 262 CID New 4.3L 2001-02 Chevrolet, GMC G2,3 (L35)(4.3W) MT1 Engine-Specific ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 101 August 2004 ... 262 CID New 4.3L 2001 Chevrolet, GMC LM1 (L35) 2001-02 Chevrolet, GMC T1 ... (L35) 2001-03 Chevrolet, GMC T1 (LG3) M30 2002 Chevrolet, GMC ... LM1 (LU3) Engine-Specific Content: Light Duty Deep Oil Pan, ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 102 August 2004 ... 262 CID New 4.3L 1997-99 Chevrolet, GMC P3 (L35) MT1 1997-00 Chevrolet, GMC ... G2,3 (L35) MT1, NA4 (exc. ZK3) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Notes: When replacing a 1998 prior GW engine (12369214), also use flywheel (12557584 ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer (part number 12346004) or ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 112 August 2004 ... .0H) 1991-92 Cadillac D (L03)(5.0H) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Cover INSTALLATION INSTRUCTIONS This engine is built with 1993 production ... components. When servicing engine, use 1993 service parts. For "D" and "F ... pan and replace with pan from replaced engine or order oil pan kit, part number ... W thread sealer, part number 12345493. Engine built after 04/13/94 have roller timing ... bolt part number 9417950 must be used. Engines built with link timing chain must use ... and bolt part number 3874878. This engine is built to production point of build ... 305 CID New 5.0L 1987-95 Chevrolet, GMC G1,2 (L03)(5.0H) 1987 Chevrolet, GMC ... ,2 V1 (L03)(5.0H) 1988-95 Chevrolet, GMC CK1,2 (L03)(5.0H) Engine-Specific ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 124 August 2004 ... CID Reman 6.0L 1985-90 Chevrolet, GMC B6, C6,7, P6, S7 (L86)(366) 1988-90 ... Chevrolet, GMC C6,7 (LS0)(366) NA5 1988-90 ... Chevrolet, GMC B6 (LS0)(L86) 1990 Chevrolet, GMC ... INSTRUCTIONS This Chevrolet Mark IV engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts ... , and valve covers to the replacement engine. Thoroughly clean all old parts to avoid ... install the sensor on the replacement engine. Use a thread sealer to prevent coolant ... in place of the pump supplied with this engine. Attach two Goodwrench engine decals ( ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 129 August 2004 ... CID Reman 7.0L 1985-90 Chevrolet, GMC C7 (L43) 1988-90 Chevrolet, GMC C6, ... 7 (L43) NA5 (427) 1990 Chevrolet, GMC C5,6,7 (LR0) 1990 Chevrolet, GMC P6 ... INSTRUCTIONS This Chevrolet Mark IV engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Part and ... and valve covers to the replacement engine. Thoroughly clean all old parts to avoid ... install the sensor on the replacement engine. Use a thread sealer to prevent coolant ... in place of the pump supplied with this engine. Attach two Goodwrench engine decals ( ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 132 August 2004 ... 454 CID New 7.4L 1974-86 Chevrolet, GMC C2,3 K3 (LE8)-454N (LF8)-454W 1984-93 ... Chevrolet, GMC P3 (LE8)(LF8)(L19) KC4 1987-91 ... Chevrolet, GMC R2,3 (L19)(LE8) 1987-91 Chevrolet, ... GMC V3 (L19)(LE8) 1988-93 Chevrolet, GMC CK1,2,3 (L19) 1988-93 Chevrolet, GMC ... G3 (L19)-454N Engine-Specific Content: Crankshaft Balancer, Front ... INSTRUCTIONS All part number 88890529, Goodwrench 7.4 Liter engine assembly, has been ... developed as a service replacement engine for 1974-1993 light duty truck 454 C.I ... .D. engine applications. When using this engine to ... Transmission 15637093 C3 1988-90 Manual Transmission 15637094 K3 1988-90 ... Manual Transmission 15637099 G3 1988-90 ... | |
