Catalog: GM Goodwrench Engines Catalog | |
| PARTS SPECIFICATION Goodwrench Service Replacement Engines (New/Reman) . .. . 3 RPO ... INSTRUCTION 8 Section IV GENERAL ENGINE DIAGNOSTICS ..17 Section V ... GOODWRENCH SERVICE REPLACEMENT ENGINES ...30 Application Content Installation ... Procedures 4-Cylinder Engine Family Gasoline 2.2L .. 31 2.3L .. 35 ... .. 41 2.5L .. 42 Straight 4 In-Line Engine Family Gasoline 2.8L .. 62 Straight 5 ... In-Line Engine Family Gasoline 3.5L .. 64 V6 Engine ... .. 79 4.3L .. 88 Straight 6 In-Line Engine Family Gasoline 4.2L .. 104 V8 Engine ... 0L .. 129 7.4L .. 131 8.1L .. 134 V8 Engine Family Diesel 6.5L .. 137 Section VI ... | |
| Page 11 August 2004 NON-TRANSFERABLE ENGINE COMPONENTS Some components off the old ... engine will not be able to be used on the new ... replacement engine. This is because they will hinder the ... performance of the engine if they are not replaced. Or, they are ... previously used in the original engine may be clogged or is worn out. The ... replaced prior to installing the new engine. Oil Pump, Pick-up Tube and Screen These ... components come with the new engine. PCV Valve and Crankcase Breather Filter ... that the emission standards of the engine are met and to prevent sludge, caused ... proper heat range for the vehicle and engine application. Failure to change the ... a choke and affect fuel consumption and engine performance. Cooling System Sealing ... prevent shaft seal damage. Fuel Filter Engine Oil Antifreeze Coolant Engine Oil ... | |
| GENERAL ENGINE DIAGNOSTICS Section IV Page 17 August ... 2004 Proper diagnosis of a failed engine is critical. Otherwise, the same ... and reliability of the best replacement engine. As such, verifying proper ... operation of the various engine systems is mandatory to avoid another ... schedules must be followed on the replacement. CAUSES OF ENGINE FAILURE Engines rely ... Lubrication Cooling Emission Controls Engine Controls Various problems in any one ... of these systems can degrade engine performance and prevent the engine from ... symptoms will become evident before the engine suffers a catastrophic failure or ... serious internal damage to require its replacement. On newer vehicles, electronic engine ... noticed. While many factors can impact engine performance and driveability, the most ... | |
| GENERAL ENGINE DIAGNOSTICS Section IV Page 20 August ... Coolant Circulation Diagnosis Proper engine operation depends on coolant to flow ... through the engine water jackets and absorb the heat of ... flowing through the radiator. A typical engine (coolant) operating temperature is ... about 200 F (94 C); some older engines run cooler and some newer engines run ... hotter. With proper flow, the engine coolant in most vehicles can readily ... flow or volume of coolant is too low, engine temperatures may rise beyond design ... specifications. The engine may seize as various parts burn off ... lubrication and expand. Engine failures caused by overheating from ... are common. The most common cause of engine overheating is poor coolant circulation ... problem is not corrected, a replacement engine will also fail. The following ... | |
| GENERAL ENGINE DIAGNOSTICS Section IV Page 21 August ... or Detonation Diagnosis With normal engine operation, the combustion process is ... power. Today's internal combustion engines operate on a basic four-stroke cycle: ... four-stroke cycle takes place in each engine cylinder according to a certain ... a smooth power flow results in optimum engine performance. The long-term effects of ... off. The common owner concern is engine "knocking". Uncorrected, the damage can ... be significant and require an engine replacement. Such damage can include cracked pistons ... or carbon deposits removed using an engine cleaner. If the engine failure has ... system repairs are needed. Replacing an engine without correcting the failure cause ... sensors, TPS and IAC valve. Check the engine control module as well. Typical ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 30 August 2004 4- ... Cylinder Engine Family Gasoline APPLICATION, CONTENT ... and applications regarding any engine, please refer to the appropriate ... electronic GM Parts Catalog or contact PARTECH at 1- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 31 August 2004 ... 1990-91 Chevrolet J, L (LM3)(2.2G) Engine-Specific Content: Crankshaft Balancer, Front ... Oldsmobile, Buick A (LN2)(2.2-4) Engine-Specific Content: Crankshaft Balancer, Front ... Chevrolet, Pontiac J (LN2)(2.2-4) Engine-Specific Content: Crankshaft Balancer, Front ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 32 August 2004 ... CID Reman 2.2L 1994-95 Chevrolet, GMC S1 (LN2)(2.2-4) 1994-95 GMC Z1 (LN2 ... )(2.2-4) Engine-Specific Content: Front Cover, Oil Pan, and Oil ... 134 CID Reman 2.2L 1996 Chevrolet, GMC S1 (03-53)(LN2)(2.2-4) Engine- ... 134 CID Reman 2.2L 1997 Chevrolet, GMC S1 (LN2)(03-53) Engine-Specific ... 134 CID New 2.2L 1998 Chevrolet, GMC S1 (LN2)(2.2-4)(03-53) MFI Engine- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 33 August 2004 ... N (L61) 2004-05 Chevrolet N (L61) Engine-Specific Content: Oil Pan, Front Cover, and ... , transfer flywheel from existing engine. For 2003 MY, fuel rail/injectors must ... 3Z (L61) 2005 Chevrolet 3A (L61) Engine-Specific Content: Oil Pan and Front Cover ... , transfer flywheel from existing engine. INSTALLATION INSTRUCTIONS No special ... Chevrolet, Pontiac J (LN2)(2.2-4) MFI Engine-Specific Content: Front Cover, Spark Plugs, and ... instructions are included with the engine. 88894189 134 CID New 2.2L 1998 ... Chevrolet, Pontiac J (LN2)(2.2-4) MFI Engine-Specific Content: Oil Pan, Front Cover, Spark ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 34 August 2004 ... CID New 2.2L 1999-2000 Chevrolet, GMC S1 (LN2) 2000 Chevrolet, GMC S1 ( ... L43) 2001-02 Chevrolet, GMC S1 (L43) MW2, M30, NC1, NF4, NF7 2003 ... Chevrolet, GMC S1 (LN2) M30, MW2 Engine-Specific Content: Front Cover, Spark Plugs, and ... instructions are included with the engine ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 35 August 2004 ... 2.3A) 1990 Oldsmobile W (LG0)(2.3A) Engine-Specific Content: Camshaft Housing, Front Cover ... Pump INSTALLATION INSTRUCTIONS This engine has been remanufactured subsequent to ... service information (i.e., 1989 engines by incorporate design features normally ... If future service is necessary for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... repair procedures. After removing old engine, use new seals and gaskets and transfer ... tube and cap/indicator. Attach Quad IV engine decal (enclosed in instruction envelope ... ). Install replacement engine and add 4 quarts of Starburst certified ... mark. CAUTION: The oil pump in this engine must be primed before starting. Crank ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 36 August 2004 ... Pontiac, Chevrolet N (LG0)(2.3A) Engine-Specific Content: Camshaft Housing, Front Cover ... Pump INSTALLATION INSTRUCTIONS This engine has been remanufactured subsequent to ... service information (i.e., 1989 engines by incorporate design features normally ... If future service is necessary for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... repair procedures. After removing old engine, use new seals and gaskets and transfer ... tube and cap/indicator. Attach Quad IV engine decal (enclosed in instruction envelope ... ). Install replacement engine and add 4 quarts of Starburst certified ... mark. CAUTION: The oil pump in this engine must be primed before starting. Crank ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 37 August 2004 ... , Oldsmobile, N (LD2)(2.3D) Buick Engine-Specific Content: Camshaft Housing, Front Cover ... Pump INSTALLATION INSTRUCTIONS This engine has been remanufactured subsequent to ... service information (i.e., 1989 engines by incorporate design features normally ... If future service is necessary for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... repair procedures. After removing old engine, use new seals and gaskets and transfer ... tube and cap/indicator. Attach Quad IV engine decal (enclosed in instruction envelope ... ). Install replacement engine and add 4 quarts of Starburst certified ... mark. CAUTION: The oil pump in this engine must be primed before starting. Crank ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 38 August 2004 ... Pontiac, Oldsmobile N (LD2)(2.3D) Engine-Specific Content: Camshaft Housing, Front Cover ... Pump INSTALLATION INSTRUCTIONS This engine has been remanufactured subsequent to ... service information (i.e., 1989 engines by incorporate design features normally ... If future service is necessary for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... repair procedures. After removing old engine, use new seals and gaskets and transfer ... tube and cap/indicator. Attach Quad IV engine decal (enclosed in instruction envelope ... ). Install replacement engine and add 4 quarts of Starburst certified ... mark. CAUTION: The oil pump in this engine must be primed before starting. Crank ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 39 August 2004 ... Pontiac, Oldsmobile N (LG0)(2.3A) Engine-Specific Content: Camshaft Housing, Front Cover ... for adapting current model Goodwrench engines into past model applications. The ... require attachment on the Goodwrench engine. LG0 (2.3A) engines may require ... crankshaft balancer on the Goodwrench engine is the same diameter as the original ... original balancer to the Goodwrench engine. Pontiac Grand Prix and Oldsmobile ... Supreme with LD2 (2.3D) or LG0 (2.3A) engines require an M12 x 1.75 bolt (part ... along with the two included M12 x 1.75 engine lift bracket bolts, to attach the ... engine mount strut bracket to the engine drill out the hole (12.5MM) on the ... bolt 22579611 is included in service engine installation kit, catalog group 0.010 ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 40 August 2004 ... Chevrolet, Pontiac J (LD2)(2.3D) MN4 Engine-Specific Content: Camshaft Housing, Front Cover ... for adapting current model Goodwrench engines into past model applications. The ... require attachment on the Goodwrench engine ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 41 August 2004 ... , Oldsmobile, N (LD9)(2.4T) Buick Engine-Specific Content: Camshaft Housing, Front Cover ... , Buick 1999 Pontiac N (LD9)(2.4T) Engine-Specific Content: Front Cover, Oil Check Valve, ... N (LD9) 2000-01 Pontiac N (LD9) Engine-Specific Content: Oil Pan, Timing Chain Housing ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 42 August 2004 ... Buick 1990 Chevrolet W (LR8)(2.5R) Engine-Specific Content: Crankshaft Balancer, Front ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 43 August 2004 ... Buick 1986 Chevrolet P (LR8)(2.5R) Engine-Specific Content: Crankshaft Balancer, Front ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 44 August 2004 ... 1985 Chevrolet, Buick X (LR8)(2.5R) Engine-Specific Content: Crankshaft Balancer, Front ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 45 August 2004 ... , Buick 1984 Pontiac P (LR8)(2.5R) Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 46 August 2004 ... A, X (LR8)(2.5R) Oldsmobile, Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 47 August 2004 ... , Oldsmobile N (L68)(2.5U) Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 48 August 2004 ... , Oldsmobile N (L68)(2.5U) Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 49 August 2004 ... N (L68)(2.5U) w/M.T. Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 50 August 2004 ... N (L68)(2.5U) w/A. Trans Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 51 August 2004 ... , Oldsmobile N (L68)(2.5U) Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 52 August 2004 ... CID Reman 2.5L 1989-90 Chevrolet, GMC M1, S1 (LN8)(2.5E) 1989-91 Chevrolet ... , GMC Z1 (LN8)(2.5E) 1991 Chevrolet, ... Oldsmobile S1 (LN8)(2.5E) GMC Engine-Specific Content: Front Cover and Oil Pan Notes ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 53 August 2004 ... 151 CID Reman 2.5L 1988 Chevrolet, GMC M1, ST1, Z1 (LN8)(2.5E) Engine- ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 54 August 2004 ... 1986 Chevrolet M1, ST1 (LN8)(2.5E) Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 55 August 2004 ... 1985 Chevrolet M1, ST1 (LN8)(2.5E) Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 56 August 2004 ... , Buick 1988 Pontiac P (LR8)(2.5R) Engine-Specific Content: Front Cover INSTALLATION ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 57 August 2004 ... , Oldsmobile, N (L68)(2.5U) Buick Engine-Specific Content: Front Cover INSTALLATION ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 58 August 2004 ... 1991 Oldsmobile, Buick N (L68)(2.5U) Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 59 August 2004 ... Chevrolet, Oldsmobile, S1 (L38)(2.5A) GMC 1991-93 GMC Z1 (LLV)(L38)(2.5A) ... Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 60 August 2004 ... , A (LR8)(2.5R) Oldsmobile, Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... service information (i.e., 1982 engines may incorporate design features ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... all necessary components to the replacement engine. Thoroughly clean all old parts ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 61 August 2004 ... Straight 4 In-Line Engine Family Gasoline APPLICATION, CONTENT ... and applications regarding any engine, please refer to the appropriate ... electronic GM Parts Catalog or contact PARTECH at 1- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 62 August 2004 ... 173 CID New 2.8L 2004 Chevrolet, GMC ST1 (LK5)(2.8-8) MA5, M30, JJA ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 63 August 2004 ... Straight 5 In-Line Engine Family Gasoline APPLICATION, CONTENT ... and applications regarding any engine, please refer to the appropriate ... electronic GM Parts Catalog or contact PARTECH at 1- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 64 August 2004 ... 214 CID New 3.5L 2004 Chevrolet, GMC S1 (L52) M30, MA5 DOHC INSTALLATION ... 214 CID New 3.5L 2004 Chevrolet, GMC T1 (L52) DOHC INSTALLATION ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 65 August 2004 V6 ... Engine Family Gasoline APPLICATION, CONTENT ... and applications regarding any engine, please refer to the appropriate ... electronic GM Parts Catalog or contact PARTECH at 1- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 66 August 2004 ... ) 1985-96 Oldsmobile A (LE2)(2.8X) Engine-Specific Content: Flywheel, Oil Pan, Torsional ... Only INSTALLATION INSTRUCTIONS This engine is built to production point of build ... necessary to retorque any bolts. This engine is built with current valve rocker ... necessary to use covers from replaced engine. This engine incorporates a 'balanced' ... flywheel, part number 14018713. If replacement is necessary, replace with part number ... 173 CID New 2.8L 1982-86 Chevrolet, GMC T1 (LL2)(2.8R)(LR2)(2.8B) Engine- ... Only INSTALLATION INSTRUCTIONS This engine incorporates a 'balanced'automatic ... flywheel, part number 14100557. If replacement is necessary, replace with part number ... 14100557. This engine is built to production point of build ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 67 August 2004 ... LB8)(2.8S) A/Trans 1987-89 Chevrolet, GMC ST1 (LL2)(2.8R)(2.8S) A. Trans Engine ... Only INSTALLATION INSTRUCTIONS This engine incorporates a 'balanced'automatic ... flywheel, part number 14097667. If replacement is necessary, replace with part number ... 14097667. This engine is built with 1992 production parts. ... , use 1992 parts. Covers from replaced engine may have to be used. On "F" cars and " ... ) use oil level indicator from replaced engine. This engine is built to production ... )(2.8S), M. Trans 1987-90 Chevrolet, GMC ST1 (LL2), M. Trans 1991-93 ... Chevrolet, GMC S1 (LL2)(2.8R), M. Trans (ML3) Engine ... Only INSTALLATION INSTRUCTIONS This engine incorporates a 'balanced'flywheel, part ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 68 August 2004 ... 1997 Chevrolet, Oldsmobile N (L82) Engine-Specific Content: Front Cover, Oil Pan, Oil ... Level Sensor, Lower Intake Manifold, Engine Oil and Additive Replaces: Replaced ... -99 Chevrolet, Oldsmobile N (L82) Engine-Specific Content: Front Cover, Oil Pan, Oil ... Level Sensor, Lower Intake Manifold, Engine Oil and Additive Replaces: Replaced ... Oldsmobile U Van (LG6)(3.1D) MD9, C67 Engine-Specific Content: Front Cover and Pointer, Lower ... , Pontiac U (LG6)(3.1D) Oldsmobile Engine-Specific Content: Front Cover, Lower Intake ... Covers INSTALLATION INSTRUCTIONS This engine incorporates 1993 production parts. ... , use 1993 LG6 service parts. The engine is built to production point of build ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 69 August 2004 ... W19 Type 1 VIN 400001 thru 800000 Engine-Specific Content: Front Cover, Lower Intake ... , Oil Pan, and Valve Covers Notes: If engine is received without dampener, must ... . INSTALLATION INSTRUCTIONS This engine incorporates 1993 production parts. ... , use 1993 LH0 service parts. The engine is built to production point of build ... Chevrolet W (LH0)(3.1T) M13, NB2, NA5 Engine-Specific Content: Front Cover, Lower Intake ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 70 August 2004 ... 3.1M) 1995 Chevrolet W (L82)(3.1M) Engine-Specific Content: Front Cover, Lower Intake ... INSTALLATION INSTRUCTIONS This engine includes an oil pan with an oil level ... for hole, or use oil pan from replaced engine. 12539087 191 CID New 3.1L 1996 ... 1996-98 Oldsmobile N (L82)(3.1M) Engine-Specific Content: Front Cover, Lower Intake ... Pan, Valve Covers, Oil Level Sensor, Engine Oil and Additive Replaces: Replaced ... , Oldsmobile N (LG8)(3.1J) SFI, NC1 Engine-Specific Content: Oil Pan, Oil Filter, Valve ... Level Sensor, Lower Intake Manifold, Engine Oil and Additive Replaces: 12480891 ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 71 August 2004 ... 2001 Chevrolet W (LG8) NC1, NF4, NF7 Engine-Specific Content: Oil Pan, Oil Filter, Valve ... Level Sensor, Lower Intake Manifold, Engine Oil and Additive Replaces: 88893923, ... N (LG8) 2003 Pontiac W (LG8) Engine-Specific Content: Front Cover, Oil Pan, Oil ... By: Notes: When replacing a 2003MY engine, use the oil pan that corresponds with ... W (LG8) 2000 Chevrolet W (LG8) NF2 Engine-Specific Content: Oil Pan, Oil Filter, Valve ... Chevrolet, Pontiac, W (L82) Buick Engine-Specific Content: Front Cover, Oil Pan, Oil ... Level Sensor, Lower Intake Manifold, Engine Oil and Additive Replaces: 12480241 ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 72 August 2004 ... Oldsmobile, Buick A, N (LG7)(3.3N) Engine-Specific Content: Front Cover and Oil Pump ... , transfer oil filter adapter from old engine or order new as detailed in the ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3300 engine decals (enclosed in instructions ... the oil filter adapter from the old engine or use new part number 25537239 for ... models. CAUTION: The oil pump in this engine must be primed before starting. DAMAGE ... WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... Oldsmobile, Buick A, N (LG7)(3.3N) Engine-Specific Content: Front Cover and Oil Pump ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 73 August 2004 ... )(3.3N) 1992 Pontiac N (LG7)(3.3N) Engine-Specific Content: Front Cover and Oil Pump ... , transfer oil filter adapter from old engine or order new as detailed in the ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3300-engine decals (enclosed in instructions ... the oil filter adapter from the old engine or use new part number 25537239 for ... models. CAUTION: The oil pump in this engine must be primed before starting. DAMAGE ... WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... )(3.3N) 1993 Pontiac N (LG7)(3.3N) Engine-Specific Content: Front Cover and Oil Pump ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 74 August 2004 ... M27 1991-92 Oldsmobile W (LQ1) M27 Engine-Specific Content: Crankshaft Balancer, Flywheel ... U (LA1) NF7 2002 Buick B (LA1) NF7 Engine-Specific Content: Front Cover, Oil Pan, and ... exc. KC4) 2002 Pontiac U (LA1) NT3 Engine-Specific Content: Front Cover, Oil Pan, and ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 75 August 2004 ... , Pontiac, U (LA1) Oldsmobile Engine-Specific Content: Oil Pan, Oil Filter, Front ... New 3.4L 2003 Pontiac U (LA1) NT3 Engine-Specific Content: Oil Pump, Front Cover, Oil Pan ... N (LA1) 2003-05 Pontiac N (LA1) Engine-Specific Content: Oil Pan, Oil Filter, and ... Notes: When replacing a 2003MY engine, use the oil pan that corresponds with ... U (LA1) 2004-05 Chevrolet W (LA1) Engine-Specific Content: Oil Pan, Oil Filter, and ... By: Notes: When replacing a 2003MY engine, use the oil pan that corresponds with ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 76 August 2004 ... 2003-04 Pontiac, Oldsmobile N (LA1) Engine-Specific Content: Oil Pan, Oil Filter, and ... By: Notes: When replacing a 2003MY engine, use the oil pan that corresponds with ... , Pontiac U (LA1) Oldsmobile Engine-Specific Content: Front Cover, Oil Pan, and ... , Pontiac, U (LA1) Oldsmobile Engine-Specific Content: Oil Pan, Oil Filter, Front ... U (LA1)(3.4E) MFI HO (NC1) Oldsmobile Engine-Specific Content: Oil Pan, Oil Filter, and ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 77 August 2004 ... W (LX5)(3.5H) MFI DOHC (NF2) Engine-Specific Content: Crankshaft Balancer Assembly, ... SW, Oil Pan, Flywheel, Spark Plugs, Engine Oil Additive, Water Pump/Pulley ... G (LX5)(3.5H) MFI DOHC (NC1) Engine-Specific Content: Balancer, Flywheel, Oil Pan, ... Oil Pump, and Oil Filter Notes: For engines with physical ID of KWA or KXA, reuse ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 78 August 2004 ... 2004-05 Cadillac D (LY7) M82, MV1 Engine-Specific Content: Oil Pan and Front Cover ... New 3.6L 2005 Cadillac D,E (LY7) Engine-Specific Content: Oil Pan and Front Cover ... CID New 3.6L 2005 Buick B,W (LY7) Engine-Specific Content: Oil Pan and Front Cover ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 79 August 2004 ... )(3.8C) 1989 Pontiac H (LN3)(3.8C) Engine-Specific Content: Balance Shaft, Front Cover, ... , transfer oil filter adapter from old engine or order new. Engine does not include ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... )(3.8C) 1990 Pontiac H (LN3)(3.8C) Engine-Specific Content: Balance Shaft, Front Cover, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 80 August 2004 ... , Oldsmobile H (LN3)(3.8C) Buick Engine-Specific Content: Crankshaft Balancer, Crank and ... Cam Posn Sensor, Engine Coolant Temp Sensor, Front Cover, Int ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... , Buick A, C, E, H (LG2)(3.8B) Engine-Specific Content: Front Cover and Oil Pump ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 81 August 2004 ... Pontiac, Oldsmobile, H (L27) Buick Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... the oil filter adapter from the old engine or use new part number 25537239. ... CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... , U Van (L27)(3.8L) Oldsmobile Engine-Specific Content: Balance Shaft, Front Cover, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 82 August 2004 ... , U Van (L27)(3.8L) Oldsmobile Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... the oil filter adapter from the old engine or use new part number 24501300 and ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... , U Van (L27)(3.8L) Oldsmobile Engine-Specific Content: Balance Shaft, Front Cover, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 83 August 2004 ... , U Van (L27)(3.8L) Oldsmobile Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... the oil filter adapter from the old engine or use new part number 24501300 and ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... )(3.8L) 1992 Pontiac H (L67)(3.8L) Engine-Specific Content: Balance Shaft, Front Cover, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 84 August 2004 ... Buick C (L67) 1994 Pontiac H (L67) Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... )(3.8-1) 1995 Buick G (L67)(3.8-1)* Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 85 August 2004 ... 2000-04 Pontiac, Buick H (L36)(3.8K) Engine-Specific Content: Flywheel, Oil Pan, Lower ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... 2000-04 Buick C (L67)(3.8-1) SFI, SC Engine-Specific Content: Balancer, Flywheel, Oil Pan, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 86 August 2004 ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... 1) 2004-05 Chevrolet W (L67)(3.8-1) Engine-Specific Content: Balancer, Crank Cam Posn. ... with new or Trans Original Sens. Engine comes with 97-00 Flywheel. Replaces: ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 87 August 2004 ... New 3.8L 2005 Chevrolet W (L26) Engine-Specific Content: Crank Balancer, Flywheel, Oil ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... 3.8L 2004 Pontiac, Buick W (L26) Engine-Specific Content: Crank Balancer, Flywheel, Oil ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 88 August 2004 ... G (LB4)(4.3Z) 1985 Chevrolet, GMC C1,2 G1,2 K1, M1 (LB1)(4.3N) Engine- ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 89 August 2004 ... G (LB4)(4.3Z) 1987 Chevrolet, GMC CK1, R1,2, V1, RV1 (LB4)(4.3Z) 1987- ... 89 Chevrolet, GMC M1 (LB4) 1988 Chevrolet, GMC CK1,2, ... 3, V2 (LB4)(4.3Z) 1988-91 Chevrolet, GMC ST1 (LB4)(4.3Z) 1989-91 Chevrolet, ... GMC CK1,2 (LB4)(4.3Z) Exc. Emis. above ... 8500lb. GVW (NA4) 1987-90 Chevrolet, GMC G1,2,3 (LB4)(4.3Z) 1990 Chevrolet, ... GMC LM1 (LB4)(4.3Z) 1991 Chevrolet, GMC G1,2,3 (LB4)(4.3Z) Exc. Emis. above ... 8500lb. GVW (NA4) Engine-Specific Content: Oil Pump Notes: Includes 21- ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 90 August 2004 ... B (LB4)(4.3Z) 1992 Chevrolet, GMC CK1, ST1 (LB4)(4.3Z) 1992 Chevrolet ... , GMC CK2 (LB4) NA1 1992 Chevrolet, GMC LM1 (LB4) 1992 Chevrolet, GMC G1,2, ... 3Z) Exc. Emis. above 8500lb. GVW (NA4) Engine-Specific Content: Oil Pump Notes: Includes 21- ... PSI Oil Pressure Bypass Valve. Engine not used on GMC Typhoon and Syclone ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 91 August 2004 ... 262 CID Reman 4.3L 1993 Chevrolet, GMC ST1 (LB4)(4.3Z) Engine-Specific ... 21-PSI Oil Pressure Bypass Valve. Engine not used on GMC Typhoon and Syclone ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 92 August 2004 ... 4.3L 1993 Chevrolet B (LB4)(4.3Z) Engine-Specific Content: Oil Pump Notes: Includes 21- ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 93 August 2004 ... 262 CID Reman 4.3L 1994 Chevrolet, GMC CK1,2 (LB4)(4.3Z) 1994 Chevrolet, ... GMC ST1 (LB4)(4.3Z) MY2, M30 1994 ... Chevrolet, GMC LM1 (LB4)(4.3Z) M30 Engine-Specific Content: Oil Pump Notes: Includes 21- ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 94 August 2004 ... 262 CID Reman 4.3L 1994 Chevrolet, GMC LM1 (L35)(4.3W) M30 1994 Chevrolet ... )(L35)(4.3W) MY2, M30 1994 Chevrolet, GMC ST1 (06-16)(L35)(4.3W) M30 (exc. CTF ... ) Engine-Specific Content: Oil Pump Notes: Includes 21- ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 95 August 2004 ... 262 CID Reman 4.3L 1994 Chevrolet, GMC ST1 (L35)(4.3W) M30, CTF 1995 ... Chevrolet, GMC ST1 (L35)(4.3W) M50, M30, NM8 (exc. ... NM8) 1995 Chevrolet, GMC ST1 (L35)(4.3W) M50, NM8, W99 (exc. ... NM8) 1995 Chevrolet, GMC LM1 (L35) M30 Engine-Specific Content ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 96 August 2004 ... Heavy Duty 4.3L 1985-89 Chevrolet, GMC P4 Eng Dress Kit (LSA)* 1990-93 ... Chevrolet, GMC CK2, P3 (LB4)(4.3Z), Emis. above ... 8500lb. GVW (NA4) 1991-93 Chevrolet, GMC G3 (LB4)(4.3A) Emis. above 8500lb. GVW ... (NA4) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Rocker Cover Notes: *Effective with engine codes ADF, AJZ, FLX, and XDF. ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 97 August 2004 ... 262 CID New 4.3L 1996 Chevrolet, GMC P3 (L35)(4.3W) CPI, MT1* 1996-2000 ... Chevrolet, GMC CK1, S1 (L35) 1996-2000 Chevrolet, ... GMC G1,2 (L35) M30, NA1 (exc. ZK3) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... replacing a 1998 and prior Goodwrench engine (12532552), also use 1-12557587 ... flywheel when replacing a Goodwrench engine (12532552) for P3 application. ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 98 August 2004 ... CID New 4.3L 1996-2000 Chevrolet, GMC, T1 (L35) Oldsmobile 1996-2000 ... Chevrolet, GMC LM1 (L35) Engine-Specific Content: Oil Pan, Oil Filter, Front ... Notes: When replacing a 1998 and prior engine, also use 1-12557587 flywheel for A. ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 99 August 2004 ... 262 CID New 4.3L 1996-99 Chevrolet, GMC S1 (LF6) M30, M50 Engine-Specific ... Notes: When replacing a 1998 and prior engine, also use 1-12557587 flywheel for A. ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 100 August 2004 ... 262 CID New 4.3L 2001-02 Chevrolet, GMC G2,3 (L35)(4.3W) MT1 Engine-Specific ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 101 August 2004 ... 262 CID New 4.3L 2001 Chevrolet, GMC LM1 (L35) 2001-02 Chevrolet, GMC T1 ... (L35) 2001-03 Chevrolet, GMC T1 (LG3) M30 2002 Chevrolet, GMC ... LM1 (LU3) Engine-Specific Content: Light Duty Deep Oil Pan, ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 102 August 2004 ... 262 CID New 4.3L 1997-99 Chevrolet, GMC P3 (L35) MT1 1997-00 Chevrolet, GMC ... G2,3 (L35) MT1, NA4 (exc. ZK3) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Notes: When replacing a 1998 prior GW engine (12369214), also use flywheel (12557584 ... should be between 300 and 500 miles. Replacement of oil related parts: If the original ... engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 103 August 2004 ... Straight 6 In-Line Engine Family Gasoline APPLICATION, CONTENT ... and applications regarding any engine, please refer to the appropriate ... electronic GM Parts Catalog or contact PARTECH at 1- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 104 August 2004 ... 256 CID New 4.2L 2002-04 Chevrolet, GMC ST1 (LL8) Engine-Specific Content: ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 105 August 2004 V8 ... Engine Family Gasoline APPLICATION, CONTENT ... and applications regarding any engine, please refer to the appropriate ... electronic GM Parts Catalog or contact PARTECH at 1- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 106 August 2004 ... 0L 1995-99 Oldsmobile G (L47)(4.0C) Engine-Specific Content: Drive Belt Tensioner, Front ... 4.0L 2001-02 Oldsmobile G (L47) Engine-Specific Content: Drive Belt Tensioner, Front ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 107 August 2004 ... Chevrolet B (L99)(4.3W) (exc. KL5) Engine-Specific Content: Oil Pan, Water Pump, Oil Pump ... . Will not work for W/KL5. See partial engine 12524501 1994-96 (W/KL5). Replaces: ... B (L99)(4.3W) (exc. KL5) Natural Gas Engine-Specific Content: Oil Pan, Water Pump, Oil Pump ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 108 August 2004 ... 4.6-9) 1994 Cadillac K (L37)(4.6-9) Engine-Specific Content: Cam Crank Posn Sensors, ... 4.6L 1995-99 Cadillac K (L37)(4.6Y) Engine-Specific Content: Cam Crank Posn Sensors, ... Camshaft Covers, Crankshaft Balancer, Engine Oil Manifold, Front Cover, Flywheel, ... 4.6L 1995-99 Cadillac K (LD8)(4.6Y) Engine-Specific Content: Cam Crank Posn Sensors, ... Camshaft Covers, Crankshaft Balancer, Engine Oil, Front Cover, Flywheel, Oil Fill ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 109 August 2004 ... )(4.6Y) 1994 Cadillac K (LD8)(4.6Y) Engine-Specific Content: Cam Crank Posn Sensors, ... Housing, Water Pump w/Pulley, and Engine Oil Replaces: 12369569, 12529512 ... 4.6L 2000 Cadillac K (L37) Notes: Engine assembly is used with and without V03 ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 110 August 2004 ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 111 August 2004 ... 292 CID New 4.8L 1999 Chevrolet, GMC CK1 (LR4)(4.8V) M30 Engine-Specific ... 292 CID New 4.8L 1999 Chevrolet, GMC CK1 (LR4) MG5 Engine-Specific Content ... 292 CID New 4.8L 2000 Chevrolet, GMC CK1 (LR4) M30 Engine-Specific Content ... 292 CID New 4.8L 2000 Chevrolet, GMC CK (LR4) MG5 Engine-Specific Content ... 292 CID New 4.8L 2000-04 Chevrolet, GMC CK1 (LR4) 2003-04 Chevrolet, GMC G2 ... ,3 (LR4) MT1 Engine-Specific Content: Harmonic Balancer, Oil Pan, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 112 August 2004 ... .0H) 1991-92 Cadillac D (L03)(5.0H) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Cover INSTALLATION INSTRUCTIONS This engine is built with 1993 production ... components. When servicing engine, use 1993 service parts. For "D" and "F ... pan and replace with pan from replaced engine or order oil pan kit, part number ... W thread sealer, part number 12345493. Engine built after 04/13/94 have roller timing ... bolt part number 9417950 must be used. Engines built with link timing chain must use ... and bolt part number 3874878. This engine is built to production point of build ... 305 CID New 5.0L 1987-95 Chevrolet, GMC G1,2 (L03)(5.0H) 1987 Chevrolet, GMC ... ,2 V1 (L03)(5.0H) 1988-95 Chevrolet, GMC CK1,2 (L03)(5.0H) Engine-Specific ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 113 August 2004 ... 305 CID New 5.0L 1996-99 Chevrolet, GMC CK1,2 (L30)(5.0M) MG5, M30 1996-2002 ... Chevrolet, GMC G1,2 (L30)(5.0M) M30 Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... : For 2001 G-van application, service engine block contains English threads. When ... 1986-87 Oldsmobile G (LG8)(5.0-9) Engine-Specific Content: Crankshaft, Inj Pump Drive, ... , Push Rods, and Timing Chain Notes: Engine does not include Water Pump, Intake or ... location during normal handling of the engine. Prior to reinstallation of the oil pan ... , remove the oil pump from the old engine. If the engine being replaced has high ... well, transfer the pump from the old engine. Failure to change the pump will result ... screen height. This remanufactured engine contains the following materials for ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 114 August 2004 ... 323 CID New 5.3L 1999 Chevrolet, GMC CK1,2 (LM7)(5.3T) M30 Engine-Specific ... 323 CID New 5.3L 2000 Chevrolet, GMC CK1 (LM7)(5.3T) MFI Engine-Specific ... 323 CID New 5.3L 2001 Chevrolet, GMC CK1,2 (LM7) 2002 Chevrolet, GMC C1, ... 2 K1 (LM7) 2002-04 Chevrolet, GMC CK1 (L59) M30 2003-04 Chevrolet, GMC ... M30, NC8, NF4, NT9 2003-04 Chevrolet, GMC CK1 (LM7) M30 2004 Chevrolet, GMC ... CK1 (LM7) M33 Engine-Specific Content: Harmonic Balancer, Oil Pan, ... 323 CID New 5.3L 2003-04 Chevrolet, GMC ST1 (LM4) M30 Engine-Specific Content ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 115 August 2004 ... B (LM1)(350-6) SEO 1979-84 Chevrolet, GMC CK1 (06)(LT9)(350M) (LS9)(350L) 1979- ... 85 Chevrolet, GMC K1 (LS9)(350L) 1980-85 Chevrolet, ... GMC G1,2,3 (LT9)(350M) (LS9)(350L) (LM1)( ... 350L) 1981-82 Chevrolet, GMC CK1 (03)(LM1)(350L) 1985 Chevrolet, ... GMC CK1(06) G1 (LS9)(350L) Engine-Specific Content: Front Cover, Oil Pan, and ... Goodwrench 5.7 Liter (350 C.I.D.) V8 engine is to be used on 1973 through 1985 ... or "L" and 1973 through 1985 Chevrolet- GMC light duty truck with VIN "Y" or "L". ... and crankshaft before installing engine. Check engine restrictor at center of ... manifold side gaskets from replaced engine and procure one of the following units ... front cover assembly from replaced engine. Some models may require R.H. cylinder ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 116 August 2004 ... 5.7L 1999 Chevrolet Y (LS1)(5.7G) Engine-Specific Content: Front Cover, Harmonic Balancer ... 5.7K) 1992 Oldsmobile B (L05)(5.7K) Engine-Specific Content: Crankshaft Hub, Oil Pan, and ... Part number 12513151 5.7 Liter engine is built with 1993 model year designed ... oil pan gasket. When servicing this engine, it is required that replacement parts ... or with new part number 12518044. Engines built after 04/13/94 have roller timing ... 14088783 and bolt part number 9417950. Engine built with link timing chain must use ... and bolt part number 3874878. This engine is built to production point of build ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 117 August 2004 ... 350 CID New 5.7L 1987-94 Chevrolet, GMC G3 (L05)(5.7K) Emis. Sys (above 8500lb ... . GVW) NA4 1987-90 Chevrolet, GMC P2,3 (L05)(5.7K) Emis. Sys (above ... 8500lb. GVW) NA4 1987-91 Chevrolet, GMC RV2,3 (L05)(5.7K) Emis. Sys (above ... 8500lb. GVW) NA4 1988-95 Chevrolet, GMC CK2,3 (L05)(5.7K) Emis. Sys (above ... 8500lb. GVW) NA4 1991-96 Chevrolet, GMC P3 (L05)(5.7K) 1994-96 Chevrolet, ... GMC G3 (L05)(5.7K) MT1 (exc. KL5, 5Z1, 9C2 ... , NM8) 1994-96 Chevrolet, GMC G3 (L05)(5.7K) NM8, MT1 (exc. 9C2) ... 1994-96 Chevrolet, GMC G3 (L05)(5.7K) 5Z1 (exc. 9C2, NM8) ... 1995 Chevrolet, GMC G3 (L05)(5.7K) MT1, 9C2, 5Z1 (exc. NM8 ... ) Engine-Specific Content: Front Cover, Oil Pan, ... 12520270 5.7 Goodwrench 5.7 Liter engine is built with 1993 model year designed ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 118 August 2004 ... New 5.7L 1996 Chevrolet Y (LT4) Engine-Specific Content: Front Cover, Oil Pan, Oil Pump ... 350 CID New 5.7L 1987-92 Chevrolet, GMC G1,2,3 (L05)(5.7K) MD8 1987 ... Chevrolet, GMC RV1,2 (L05)(5.7K) Emis. Sys (under ... 8500lb. GVW) NA1 1988 Chevrolet, GMC CK1,2 (L05)(5.7K) 1988-91 Chevrolet ... , GMC RV1 (L05)(5.7K) 1989-95 Chevrolet, ... GMC CK1,2 (L05)(5.7K) Emis. Sys (under ... 8500lb. GVW) NA1 1993-94 Chevrolet, GMC G1,2,3 (L05)(5.7K) Emis. Sys (under ... 8500lb. GVW) NA1 1995 Chevrolet, GMC G2,3 (L05)(5.7K) M30 Emis. Sys (under ... 8500lb. GVW) NA1 Engine-Specific Content: Front Cover and Pointer, Oil ... 350 CID New 5.7L 1986 Chevrolet, GMC CK1 (LS9)(350L) 1986 Chevrolet, GMC ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 119 August 2004 ... 350 CID New 5.7L 1993-95 Chevrolet, GMC W4 (L05) 2000 Chevrolet, GMC W4 ... Engine-Specific Content: Oil Pan INSTALLATION ... Chevrolet Y (LS1)(5.7G) MFI Alum Engine-Specific Content: Front Cover, Harmonic Balancer ... -00 Chevrolet, Pontiac F (LS1)(5.7G) Engine-Specific Content: Front Cover, Harmonic Balancer ... Chevrolet, Pontiac F (LS1)(5.7G) Engine-Specific Content: Front Cover, Harmonic Balancer ... .7P) 1994-95 Cadillac B (LT1)(5.7P) Engine-Specific Content: Crankshaft Hub and Valve ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 120 August 2004 ... )(5.7P) 1996 Cadillac B (LT1)(5.7P) Engine-Specific Content: Front Cover, Oil Pan, Oil Pump ... 5.7P) 1995 Chevrolet Y (LT1)(5.7P) Engine-Specific Content: Crankshaft Hub, Front Cover, ... pump with part number 12555283. This engine is built to production point of build ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 121 August 2004 ... 7P) 1992-94 Chevrolet Y (LT1)(5.7P) Engine-Specific Content: Crankshaft Hub, Front Cover, ... pump with part number 12555283. This engine is built with 1994 production parts. ... valve train, use 1994 components. This engine is built to production point of build ... 5.7P) 1996 Chevrolet Y (LT1)(5.7P) Engine-Specific Content: Front Cover, Oil Pan, Oil Pump ... pump with part number 12555283. This engine is built to production point of build ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 122 August 2004 ... New 5.7L 2001 Chevrolet Y (LS6) Engine-Specific Content: Harmonic Balancer, | |
