Catalog: GM Goodwrench Engines Catalog | |
| Plugs Caps (valve) Gaskets All Cover Fuel Pump Opening Gear Balance Shaft ... Balance Shaft Driven (typically) Front Covers (if applicable) Flat Lifters Intake ... (if applicable) Nut-Connecting Rod Oil Fill Cap Nut Rocker Arm Stud Oil Pan ... Oil Pump Pushrods Pistons Pin and Rings ... Camshaft and Crankshaft Rocker Covers (if applicable) Timing Chain Rotators ... (valve) Valve Oil Filter Bypass Shaft Distributor to Oil ... Pump Valves Inlet and Exhaust Valve ... | |
| replaced to prevent a leak in the front cover seal. Intake Manifold Inspect the ... cleaning the intake manifold. Valve Covers Inspect the sealing surfaces of the ... valve covers for flatness and check for cracks at ... holes. If any cracks are found on the covers, they must be replaced. Do not try to ... repair them. Clean the covers and check for loose baffles at the fill ... holes and PCV outlets. Replace the cover(s) if they are defective. Oil Pan ... Inspect the oil pan rail for flatness. Check for ... bold holes. Check the front and rear oil pan seat rails for cracks or damage. If ... cracks are found replace the oil pan. Do not try to repair them. Inspect ... the oil drain plug for stripped threads or a ... cracks or a loose weld nut. Front Cover and Lower End Replace the crankshaft ... | |
| and remove silicates from the water pump shaft that form from the coolant. ... the engine on an engine stand with the oil pan facing upwards, intake valley ... 's specifications. 1. Install the oil pump and the oil pump shaft. Fill the pump ... the initial suction and priming of the pump. Do not use white lithium grease to pack ... the oil pump. This grease won't breakdown and will ... clog oil passages, which could cause engine oil ... and seizing. 2. Install the new oil pick-up tube and screen and the ... crankshaft oil slinger. Be sure not to install the oil ... screen too close to the oil pan. Installing it too close can hinder ... the pick-up of oil causing oil starvation and seizing. Be sure to ... of the crank. 4. Install the front cover using a front cover alignment tool. ... | |
| the intake valley is facing up and the oil pan is facing down. 9. Pour the ... with A.P.I. Starburst certified motor oil. Pre-lubing the engine is necessary to ... engine can be pre-lubed by priming the oil pump with a hand-held drill. Using an ... oil pump priming tool or distributor shaft, ... rotate the oil pump with a drill at 200 to 500 RPM for two ... damage. 13. Install the valve covers and be sure to tighten those fasteners ... in the proper sequence. The valve covers need to seal properly to avoid damage ... manifold(s). 16. Install the fuel pump and fuel lines being sure of proper ... end bracketry Crankshaft pulley Water pump pulley Air conditioning compressor Air ... pump Alternator (generator) Power steering ... pump All sensors that were removed from the ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, Spark Plugs, ... and Water Pump INSTALLATION INSTRUCTIONS This engine ... all necessary components, such as oil fill tube and cap/indicator. Attach ... and add 4 quarts of Starburst certified oil of a viscosity recommended for your ... climate, and prime oil system. Check oil level on dipstick and add oil as ... to reach the full mark. CAUTION: The oil pump in this engine must be primed ... with the ignition system disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. ... Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, Spark Plugs, ... and Water Pump INSTALLATION INSTRUCTIONS This engine ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, P/S Pump Pulley, Spark ... Plugs, and Water Pump INSTALLATION INSTRUCTIONS This engine ... all necessary components, such as oil fill tube and cap/indicator. Attach ... and add 4 quarts of Starburst certified oil of a viscosity recommended for your ... climate, and prime oil system. Check oil level on dipstick and add oil as ... to reach the full mark. CAUTION: The oil pump in this engine must be primed ... with the ignition system disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. ... Housing, Crankshaft Housing, Front Cover, Oil Check Valve, Oil Pan, Oil Pump w/ ... Screen, P/S Pump Pulley, Spark Plugs, Timing Chain ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump ... Pulley, Spark Plugs, and Water Pump INSTALLATION INSTRUCTIONS This engine ... all necessary components, such as oil fill tube and cap/indicator. Attach ... and add 4 quarts of Starburst certified oil of a viscosity recommended for your ... climate, and prime oil system. Check oil level on dipstick and add oil as ... to reach the full mark. CAUTION: The oil pump in this engine must be primed ... with the ignition system disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. ... Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump ... Pulley, Spark Plugs, and Water Pump INSTALLATION INSTRUCTIONS This engine ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump ... Pulley, Spark Plugs, and Water Pump INSTALLATION INSTRUCTIONS This engine ... all necessary components, such as oil fill tube and cap/indicator. Attach ... and add 4 quarts of Starburst certified oil of a viscosity recommended for your ... climate, and prime oil system. Check oil level on dipstick and add oil as ... to reach the full mark. CAUTION: The oil pump in this engine must be primed ... with the ignition system disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. ... Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump ... Pulley, Spark Plugs, and Water Pump INSTALLATION INSTRUCTIONS This engine ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump ... Pulley, Spark Plugs, and Water Pump Replaces: 24574880 Replaced By: ... Notes: Does not contain Flywhl, Oil Fill Tube, C/case Vent Sys, Therm, Int ... Cr/shf Posn, Knock, Map, Cool Temp or Oil Lvl Sen. INSTALLATION INSTRUCTIONS ... applications. The mounting boss on the oil pan for the radiator outlet pipe ... engine requires transferring the water pump cover from the original engine. This is ... necessary to ensure that the water pump cover contains the nipple required for ... the heater hose. The water pump cover gaskets should be replaced at this time ... Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump ... Pulley, Spark Plugs, and Water Pump Notes: Does not contain Flywhl, Oil ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump ... Pulley, Spark Plugs, and Water Pump Notes: Does not contain Flywhl, Oil ... Cr/shf Posn, Knock, Map, Cool Temp or Oil Lvl Sen. INSTALLATION INSTRUCTIONS ... applications. The mounting boss on the oil pan for the radiator outlet pipe ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump ... Pulley, Spark Plugs, and Water Pump Notes: Does not contain Flywheel, Oil ... Posn, Knock, Map, Cool Temp or Oil Level Sensor. Order 11516479 self ... )(2.4T) Engine-Specific Content: Front Cover, Oil Check Valve, Oil Pan, Water Pump, ... N (LD9) Engine-Specific Content: Oil Pan, Timing Chain Housing, Spark Plugs ... , Water Pump, and P/S Pump Pulley Notes: Does not include ... Ignition Module, Crankshaft Posn., and Oil Level Sensors. For 1 st design, see ... | |
| Content: Crankshaft Balancer, Front Cover, Internal Balancer, Oil Pan, and Valve ... Rocker Cover INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... | |
| Content: Crankshaft Balancer, Front Cover, Internal Balancer, Oil Pan, and Valve ... Rocker Cover INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... | |
| Content: Crankshaft Balancer, Front Cover, Internal Balancer, Oil Pan, and Valve ... Rocker Cover INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... | |
| )(2.5R) Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| , Buick Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| Buick Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| Buick Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| Buick Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| Buick Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| Buick Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| ) GMC Engine-Specific Content: Front Cover and Oil Pan Notes: Must purchase ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| )(2.5E) Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| )(2.5E) Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| )(2.5E) Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| )(2.5R) Engine-Specific Content: Front Cover INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| Buick Engine-Specific Content: Front Cover INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| )(2.5U) Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| )(2.5A) Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| , Buick Engine-Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... possible damage to the engine. Rocker cover installation: A) use RTV on dimpled ... covers, B) use cork/rubber gasket (with ... limiters) with non-hemmed holes on covers, C) use silicone/steel reinforced gasket ... with non-dimpled, non-hemmed rocker covers. Attach the enclosed decal to clean ... rocker cover. Install the appropriate bushing in the ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... | |
| 8X) Engine-Specific Content: Flywheel, Oil Pan, Torsional Damper, and Valve Covers ... is built with current valve rocker cover. It may be necessary to use covers from ... 8B) Engine-Specific Content: Flywheel, Oil Pan, Front Cover, Oil Fill Cap, ... Torsional Damper, and Valve Covers Notes: Automatic Transmission Only ... is built with current valve rocker cover. It may be necessary to use covers from ... , plug fuel hole with: 1 of 14064231 Cover Fuel Pump opening 2 of 11500914 Bolts ... | |
| .8S) A. Trans Engine-Specific Content: Oil Pan, Valve Covers, Flywheel, and ... parts. For service, use 1992 parts. Covers from replaced engine may have to be ... . On "F" cars and "S" trucks: A) remove oil pan and replace with part number ... 10078999, B) remove oil pump screen assembly and replace with part ... number 10118624, C) use oil level indicator from replaced engine. ... . Trans (ML3) Engine-Specific Content: Oil Pan, Valve Covers, Flywheel, and ... . When servicing, use 1992 parts. Valve covers from replaced engine may have to be ... . On "F" cars and "S" trucks: A) remove oil pan and replace with part number ... 10078999, B) remove oil pump screen assembly and replace with part ... number 10118624, C) use oil level indicator from replaced engine. ... | |
| )(3.3N) Engine-Specific Content: Front Cover and Oil Pump Notes: For "N" car ... applications, transfer oil filter adapter from old engine or order ... instructions. Does not contain Rocker Covers, Oil Pan, Manifolds or Balancer. ... instructions envelope) to clean valve covers. Oil Filter Adapters: For "N" car ... applications, transfer the oil filter adapter from the old engine or ... for 1992-93 models. CAUTION: The oil pump in this engine must be primed before ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12356520 ... )(3.3N) Engine-Specific Content: Front Cover and Oil Pump Notes: For "N" car ... applications, transfer oil filter adapter from old engine or order ... instructions. Does not contain Rocker Covers, Oil Pan, Manifolds or Balancer. ... | |
| )(3.3N) Engine-Specific Content: Front Cover and Oil Pump Notes: For "N" car ... applications, transfer oil filter adapter from old engine or order ... instructions. Does not contain Rocker Covers, Oil Pan, Manifolds or Balancer. ... instructions envelope) to clean valve covers. Oil Filter Adapters: For "N" car ... applications, transfer the oil filter adapter from the old engine or ... for 1992-93 models. CAUTION: The oil pump in this engine must be primed before ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12356523 ... )(3.3N) Engine-Specific Content: Front Cover and Oil Pump Notes: For "N" car ... applications, transfer oil filter adapter from old engine or order ... instructions. Does not contain Rocker Covers, Oil Pan, Manifolds or Balancer. ... | |
| ) Oldsmobile Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, and Valve ... Rocker Covers Replaces: 12480881 Replaced By: ... U (LA1) NT3 Engine-Specific Content: Oil Pump, Front Cover, Oil Pan, Oil Filter ... , Valve Rocker Covers, Oil Level Sensor, Oil Fill Cap, and Lower ... N (LA1) Engine-Specific Content: Oil Pan, Oil Filter, and Rocker Covers ... When replacing a 2003MY engine, use the oil pan that corresponds with that ... W (LA1) Engine-Specific Content: Oil Pan, Oil Filter, and Rocker Covers ... When replacing a 2003MY engine, use the oil pan that corresponds with that ... | |
| , Crank Cam Posn. Sensors, Camshaft Covers, Front Cover Assembly, Filter, Level ... Indicator Assembly, Oil Level SW, Oil Pan, Flywheel, Spark Plugs, Engine Oil ... Additive, Water Pump/Pulley Assembly, Water Outlet, and ... -Specific Content: Balancer, Flywheel, Oil Pan, Oil Pump, and Oil Filter Notes: ... | |
| -Specific Content: Balance Shaft, Front Cover, Oil Filter Adapter, Oil Pump with Gears ... and Cover. Notes: For "E" car applications, ... transfer oil filter adapter from old engine or order ... new. Engine does not include Rocker Covers, Oil Pan, Intake Manifold or Exhaust ... instructions envelope) to clean valve covers. CAUTION: The oil pump in this engine ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12360022 231 CID ... -Specific Content: Balance Shaft, Front Cover, Oil Filter Adapter, Oil Pump with Gears ... and Cover Notes: For "E" car applications, ... | |
| , Engine Coolant Temp Sensor, Front Cover, Int Air Temp Sensor, Map Sensor, Oil ... Level Sensor, Oil Pressure Sensor, Spark Plugs, Themostat ... and Water Pump Notes: Does not include Intake ... instructions envelope) to clean valve covers. CAUTION: The oil pump in this engine ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12360686 231 CID ... )(3.8B) Engine-Specific Content: Front Cover and Oil Pump INSTALLATION INSTRUCTIONS ... instructions envelope) to clean valve covers. For 1986-87 "E" car applications, ... transfer the oil filter adapter from the old engine or ... new part number 25537239. CAUTION: The oil pump in this engine must be primed ... | |
| -Specific Content: Balance Shaft, Front Cover, Oil Filter Adapter, Timing Chain ... Dampener, and Oil Pump INSTALLATION INSTRUCTIONS Do not ... instructions envelope) to clean valve covers. For 1988-91 "E" car applications, ... transfer the oil filter adapter from the old engine or ... new part number 25537239. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12362214 231 CID ... -Specific Content: Balance Shaft, Front Cover, Oil Filter Adapter, Timing Chain ... Dampener, and Oil Pump INSTALLATION INSTRUCTIONS Do not ... instructions envelope) to clean valve covers. For 1992 "E" car applications, transfer ... | |
| -Specific Content: Balance Shaft, Front Cover, Oil Filter Adapter, Timing Chain ... Dampener, and Oil Pump INSTALLATION INSTRUCTIONS Do not ... instructions envelope) to clean valve covers. For 1993-95 "W" and "Z" car ... applications, transfer the oil filter adapter from the old engine or ... and studs 24500567. CAUTION: The oil pump in this engine must be primed before ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12362216 231 CID ... -Specific Content: Balance Shaft, Front Cover, Oil Filter Adapter, Timing Chain ... Dampener, and Oil Pump INSTALLATION INSTRUCTIONS Do not ... | |
| -Specific Content: Balance Shaft, Front Cover, Oil Filter Adapter, Timing Chain ... Dampener, and Oil Pump INSTALLATION INSTRUCTIONS Do not ... instructions envelope) to clean valve covers. For 1993-95 "W" and "Z" car ... applications, transfer the oil filter adapter from the old engine or ... and studs 24500567. CAUTION: The oil pump in this engine must be primed before ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12362218 231 CID ... -Specific Content: Balance Shaft, Front Cover, Oil Filter Adapter, Timing Chain ... Dampener, and Oil Pump INSTALLATION INSTRUCTIONS Do not ... | |
| -Specific Content: Balance Shaft, Front Cover, Oil Filter Adapter, Oil Pump w/Gears, ... Timing Chain Dampener, and Oil Pump Notes: 1 st design has 5/16" oil pan ... instructions envelope) to clean valve covers. CAUTION: The oil pump in this engine ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12362221 231 CID ... -Specific Content: Balance Shaft, Front Cover, Oil Filter Adapter, Oil Pump w/Gears, ... Timing Chain Dampener, and Oil Pump Notes: *2 nd design has 1/4" Oil Pan ... instructions envelope) to clean valve covers. CAUTION: The oil pump in this engine ... | |
| 8K) Engine-Specific Content: Flywheel, Oil Pan, Lower Intake Manifold, Front Cover ... , Water Pump, Balancer, and Crank Cam Posn. Sensors ... instructions envelope) to clean valve covers. CAUTION: The oil pump in this engine ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12482057 231 CID ... -Specific Content: Balancer, Flywheel, Oil Pan, Front Cover, Oil Filter, Lower ... Intake, Valve Covers, Crank Cam Posn. Sensors, and Oil Level ... instructions envelope) to clean valve covers. CAUTION: The oil pump in this engine ... priming procedures. Also, check engine oil level before starting engine. Refer to ... | |
| instructions envelope) to clean valve covers. CAUTION: The oil pump in this engine ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 89017667 231 CID ... , Crank Cam Posn. Sensors, Front Cover, Flywheel, Lower Intake Manifold, Valve ... Covers, Oil Level Sensor, Oil Pan, and Water Pump Notes: Does not ... parts. May be necessary to replace Oil Level Sensor with new or Trans ... instructions envelope) to clean valve covers. CAUTION: The oil pump in this engine ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... | |
| Content: Crank Balancer, Flywheel, Oil Pan, Front Cover, Oil Filter, Lower ... Intake, Valve Covers, Crank Cam Posn. Sensor, and Oil Level ... instructions envelope) to clean valve covers. CAUTION: The oil pump in this engine ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 89017670 231 CID ... Content: Crank Balancer, Flywheel, Oil Pan, Front Cover, Oil Filter, Lower ... Intake, Valve Covers, Crank Cam Posn. Sensor, and Oil Level ... instructions envelope) to clean valve covers. CAUTION: The oil pump in this engine ... priming procedures. Also, check engine oil level before starting engine. Refer to ... | |
| (LB1)(4.3N) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... | |
| . GVW (NA4) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... | |
| . GVW (NA4) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... | |
| (LB4)(4.3Z) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... | |
| B (LB4)(4.3Z) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... | |
| )(4.3Z) M30 Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... Pressure Bypass Valve. Does not include Oil Pan or Rocker Covers, order separately ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... | |
| (exc. CTF) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... | |
| LM1 (L35) M30 Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... | |
| (NA4) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil Pan, Oil Pump w/ ... Screen, Torsional Damper, Valve Rocker Cover Notes: *Effective with engine codes ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... | |
| . ZK3) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil Pan, Oil Pump w/ ... Screen, Torsional Damper, Valve Rocker Cover Notes: When replacing a 1998 and prior ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... | |
| LM1 (L35) Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, and Valve ... Rocker Covers Notes: When replacing a 1998 and prior ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... | |
| LF6) M30, M50 Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, and Valve ... Rocker Covers Notes: When replacing a 1998 and prior ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... | |
| : Harmonic Balancer, Balance Shaft, Oil Pan, Front Cover, and Rocker Covers ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... | |
| -Specific Content: Light Duty Deep Oil Pan, Harmonic Balancer, Front Cover, ... and Rocker Covers Replaces: 88894117, 12570474 Replaced ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... | |
| . ZK3) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil Pan, Oil Pump w/ ... Screen, Torsional Damper, Valve Rocker Cover Notes: When replacing a 1998 prior GW ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... plugs in these cylinders. Front Covers: 4.3 blocks with ten-bolt front cover ... provisions accept either ten-bolt metal covers or, after removing dowel pins, accept ... six-bolt plastic covers. On OBD II equipped engines, reluctor ... | |
| Content: Drive Belt Tensioner, Front Cover, Oil Filter, Oil Level Sensors, Oil ... Press Sensor, Oil Pump w/Screen, and Water Pump w/Pulley ... Content: Drive Belt Tensioner, Front Cover, Oil Filter, Oil Level Sensors, Oil ... Press Sensor, Oil Pump w/Screen, Water Pump w/Pulley, and Balancer Notes: Exc. ... | |
| : Cam Crank Posn Sensors, Camshaft Covers, Crankshaft Balancer, Front Cover, ... Flywheel, Oil Filter w/Adapter, Oil Pan, Oil Pump, PCV Valve, Spark Plugs, ... Thermostat Housing, and Water Pump w/Pulley Notes: Replaces: Replaced ... : Cam Crank Posn Sensors, Camshaft Covers, Crankshaft Balancer, Engine Oil ... Manifold, Front Cover, Flywheel, Oil Fill Cap, Oil Filter w/Adapter, Oil ... Level Indicator Tube Assembly, Oil Level Sensor, Oil Pan, Oil Pump ... Sensor, Thermostat Housing, Water Pump w/Housing, and Water Pump w/Pulley ... 1998 KS/KY models transfer or purchase Oil Level Indicator and Tube. 1995-97 ... models transfer or purchase Oil Filter Adapter (with oil clr ports). ... : Cam Crank Posn Sensors, Camshaft Covers, Crankshaft Balancer, Engine Oil, Front ... | |
| : Cam Crank Posn Sensors, Camshaft Covers, Crankshaft Balancer, Front Cover, ... Flywheel, Oil Filter w/Adapter, Oil Pan, Oil Pump, PCV Valve, Spark Plugs, ... Thermostat Housing, Water Pump w/Pulley, and Engine Oil Replaces: ... | |
| 8V) M30 Engine-Specific Content: Front Cover, Harmonic Balancer, Oil Pan, and Oil ... ) MG5 Engine-Specific Content: Front Cover, Harmonic Balancer, Oil Pan, and Oil ... -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, Water Pump and Rocker ... Covers INSTALLATION INSTRUCTIONS No special ... -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, Water Pump and Rocker ... Covers INSTALLATION INSTRUCTIONS No special ... -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, Water Pump and Rocker ... Covers Replaces: 88894060, 88893290, 88893289 ... | |
| 0M) M30 Engine-Specific Content: Front Cover, Oil Fill Cap, Oil Pan, and Valve Rocker ... Cover Notes: For 2001 G-van application, ... -Specific Content: Crankshaft, Inj Pump Drive, Oil Pump w/Screen, Conn. Rod and ... Notes: Engine does not include Water Pump, Intake or Exhaust Manifold, Flywheel, ... Front Cover or Oil Pan. Replaces: 22536528 Replaced By ... : INSTALLATION INSTRUCTIONS Oil Pump Screen Height: The oil pump pickup ... engine. Prior to reinstallation of the oil pan, check the location of the screen. ... Oil Pump: On all "E" or "K" models, remove the ... oil pump from the old engine. If the engine ... , it is suggested you purchase a new oil pump. If it is low mileage and the oil ... pump worked well, transfer the pump from the old engine. Failure to change ... | |
| 3T) M30 Engine-Specific Content: Front Cover, Harmonic Balancer, Oil Pan, Oil Filter ... , and Valve Rocker Covers Replaces: Replaced By: 88890540 ... 3T) MFI Engine-Specific Content: Front Cover, Harmonic Balancer, Oil Pan, Oil Filter ... , and Valve Rocker Covers Replaces: 12565185 Replaced By: ... -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, Water Pump, and ... Rocker Covers Replaces: 88984275, 88894061, 88894258 ... ST1 (LM4) M30 Engine-Specific Content: Oil Pump, Front Cover, Water Pump, and ... Rocker Covers Replaces: 88984276, 12577732 Replaced ... | |
| )(350L) Engine-Specific Content: Front Cover, Oil Pan, and Valve Covers Notes: Refer ... correct pointer or install front cover assembly from replaced engine. Some ... )(5.7G) Engine-Specific Content: Front Cover, Harmonic Balancer, Oil Filter, Oil Pan ... , Intake Manifold, Fuel Rail, and Water Pump Replaces: Replaced By: 88894382 ... | |
| )(5.7G) Engine-Specific Content: Front Cover, Harmonic Balancer, Oil Filter, Oil Pan ... , Intake Manifold, Fuel Rail, and Water Pump Replaces: Replaced By: 88890543 ... -Specific Content: Crankshaft Hub, Oil Pan, and Valve Rocker Cover ... is built with 1993 model year designed oil pan (no rail bead) and oil pan gasket ... . On "D" car models 1992 prior, remove oil pan and replace with original or with ... | |
| . NM8) Engine-Specific Content: Front Cover, Oil Pan, Torsional Damper, and Valve ... Rocker Cover Replaces: 12509657 Replaced By: ... is built with 1993 model year designed oil pan (no rail bead), oil pan gasket, ... and oil pump assembly. When servicing this engine, ... with current-production valve rocker covers. It may be necessary to use cover from ... engine. On models with a 5-Quart Oil Pan, remove oil pan and oil pump ... assembly. Replace with original or new oil pan assembly part number 12518043, oil ... pump assembly part number 10168529, and ... screen oil part number 10166159. This engine is ... Specific Content: Crankshaft Hub, Front Cover, Oil Pan, and Valve Rocker Cover Notes ... English threads. May require Valve Covers to be transferred from original engine ... | |
| Y (LT4) Engine-Specific Content: Front Cover, Oil Pan, Oil Pump w/Shaft and Cover, ... Water Pump w/Shaft and Cover Notes: Does not include Inlet Manifold ... Manifold, Starter, Flywheel, Water Pump, Ignition or Attaching Parts Replaces ... ) NA1 Engine-Specific Content: Front Cover and Pointer, Oil Pan, Torsional Damper ... , and Valve Rocker Covers Replaces: 12520268 Replaced By: ... )(350L) Engine-Specific Content: Front Cover and Valve Rocker Covers Replaces: ... GMC W4 (L31) Engine-Specific Content: Oil Pan Notes: For 2001 application, must ... | |
| , GMC W4 Engine-Specific Content: Oil Pan INSTALLATION INSTRUCTIONS No ... Alum Engine-Specific Content: Front Cover, Harmonic Balancer, Oil Filter, Oil Pan ... , Intake Manifold, Fuel Rail, and Water Pump Replaces: Replaced By: 88890544 ... )(5.7G) Engine-Specific Content: Front Cover, Harmonic Balancer, Oil Filter, Oil Pan ... , Intake Manifold, Fuel Rail, and Water Pump Replaces: 12457659 Replaced By: ... )(5.7G) Engine-Specific Content: Front Cover, Harmonic Balancer, Oil Filter, Oil Pan ... , Intake Manifold, Fuel Rail, and Water Pump Replaces: 12455110 Replaced By: ... : Crankshaft Hub and Valve Rocker Cover Replaces: 12513026 Replaced By: ... | |
| )(5.7P) Engine-Specific Content: Front Cover, Oil Pan, Oil Pump w/Shaft and Cover, ... Water Pump w/Shaft and Cover Notes: Does not include Inlet Manifold ... Specific Content: Crankshaft Hub, Front Cover, Oil Pan, and Valve Rocker Cover ... On "Y" car applications, valve covers, oil pan, and oil pump screen must be ... or purchased new as follows: Valve Covers (w/gasket) Valve Cover Bolts Oil Pump ... Screen Oil Pan Kit/Pan Gasket 12552321 LH ... 'press' after installing the oil pump screen,replace oil pump with part ... | |
| Specific Content: Crankshaft Hub, Front Cover, Oil Pan, and Valve Rocker Cover ... On "Y" car applications, valve covers, oil pan, and oil pump screen must be ... purchased new as follows: Year Valve Covers Valve Cover Bolts Oil Pump Screen ... Oil Pan Kit/Pan Gasket 1992 N/A LH ... * 10108674 10108676 *Includes valve cover gasket If there is insufficient 'press ... ' after installing the oil pump screen,replace oil pump with part ... )(5.7P) Engine-Specific Content: Front Cover, Oil Pan, Oil Pump w/Shaft and Cover, ... Water Pump w/Shaft and Cover Notes: Does not include Inlet Manifold ... Manifold, Starter, Flywheel, Water Pump, Ignition or Attaching Parts Replaces: ... On "Y" car applications, valve covers, oil pan, and oil pump screen must be ... | |
| -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, Water Pump, and ... Rocker Covers Replaces: 88894057 Replaced By: ... -Specific Content: Harmonic Balancer, Oil Pan, Oil Pump, Front Cover, Water Pump ... , and Rocker Covers Replaces: 88984272, 88894254 Replaced ... -Specific Content: Harmonic Balancer, Oil Pan, Oil Pump, Front Cover, Water Pump ... , and Rocker Covers INSTALLATION INSTRUCTIONS No special ... -Specific Content: Harmonic Balancer, Oil Pan, Oil Pump, Front Cover, Water Pump ... , and Rocker Covers Replaces: 89017348, 89017384, 89017275 ... applications may require rocker arm covers to be transferred form original engine ... | |
| -Specific Content: Harmonic Balancer, Oil Pan, Oil Pump, Front Cover, Water Pump ... , and Rocker Covers Replaces: 89017350 Replaced By: ... | |
| seals and gaskets. Install the supplied oil pump and transfer all necessary ... components including oil pan, and valve covers to the ... sensor. It may be necessary to tap the oil tube-mounting hole with 1/4-18 dry-seal ... leaks. On certain models with shallow oil pan, a new oil pump assembly, part ... tube must be installed in place of the pump supplied with this engine. Attach two ... instructions envelope) to clean valve covers. CAUTION: The oil pump in this engine ... priming procedures. Also, check engine oil level before starting engine. Use 6 ... quarts of A.P.I. Starburst certified oil in the viscosity suitable for your ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED PROPERLY ... (MT1) Engine-Specific Content: Front Cover, Harmonic Balancer, Oil Filter, Oil Pan ... | |
| 12465229 366 CID New Electric Fuel Pump Application Only 6.0L 1986-89 ... Chevrolet, GMC M4,5,6 (L86) MF1 (exc. oil cooler KPS, air comp application) 1986 ... , GMC B6 (L86) 366 (LS0) MF1 (exc. oil cooler KPS, air comp application) 1990 ... GMC B7 (LS0) Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, Valve ... Rocker Covers Notes: Electric Fuel Pump Application Only. When replacing ... , must also use 1-12529747 water pump. Replaces: 12530366 Replaced By: ... | |
| 88890535 366 CID New Mechanical Fuel Pump Application Only 6.0L 1986-89 ... Chevrolet, GMC M4,5,6 (L86) MF1 (exc. oil cooler KPS, air comp application) 1986 ... , GMC C6,7 (L86) ME4, ME6 (exc. oil cooler application (with kit 15637482 ... , GMC B6 (L86) 366 (LS0) M.T. (exc. oil cooler KPS, air comp application) 1989 ... , GMC B6 (L86) 366 (LS0) MF1 (exc. oil cooler KPS, air comp application) 1989 ... F6,7 (LS0) Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, Valve ... Rocker Covers Notes: Mechanical Fuel Pump Application Only. When replacing ... , must also use 1- 12529747 water pump. Replaces: 12530366 Replaced By: ... | |
| -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, and Water Pump ... (LQ4) Engine-Specific Content: Front Cover, Harmonic Balancer, Oil Filter, Oil Pan ... , and Valve Covers Replaces: 89017358, 88984278, 88894260 ... (LQ4) Engine-Specific Content: Front Cover, Harmonic Balancer, Oil Filter, Oil Pan ... , and Valve Covers Replaces: 88984282 Replaced By: ... -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, and Water Pump ... | |
| seals and gaskets. Install the supplied oil pump and transfer all necessary ... components including oil pan and valve covers to the replacement engine. Thoroughly ... sensor. It may be necessary to tap the oil-tube mounting hole with 1/4-18 dry-seal tap ... leaks. On certain models with shallow oil pan, a new oil pump assembly, part ... tube must be installed in place of the pump supplied with this engine. Attach two ... instructions envelope) to clean valve covers. CAUTION: The oil pump in this engine ... priming procedures. Also, check engine oil level before starting engine. Use 6 ... quarts of Starburst certified oil in the viscosity suitable for your ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. ... ME6, MF1, MT9, MWX Notes: 6-bolt Front Cover Replaces: 12524680 Replaced By: ... | |
| Chevrolet, GMC B7 (LR0) Notes: Rocker cover may have to be swapped for some ... MF1, MT9, IMT9 *indicates kit includes oil cooling. Oil Cooling Kit Model Year ... 15662081 C6,7 1986-90 LR0, L43 w/oil cooling 15662081 P6 1986-90 L43 w/ ... trucks, you must purchase a new water pump and lower radiator hose. For 1990 and ... prior, you must replace the water pump with part number 12529747 to clear the ... 8" damper. Year Water Pump Hoses Usage 1991-94 12529192 ... | |
| Content: Crankshaft Balancer, Front Cover, Oil Fill Cap, Oil Pan, Oil Pump w/ ... Screen, Oil Pump Drive Shaft, Valve Rocker Cover Notes ... : Does not use old oil adapter. Cooler lines go to block. ... 15637099 G3 1988-90 All (w/Oil Cooling) 15637100 P3 (32) 1974-90 w ... w/A.T. 15637108 K3 1974-86 w/A.T. Oil Cooling Kit Model Year Restriction ... -86 KC4 15637110 K3 1974-82 KC4* *oil cooler part number 3053355 is required ... | |
| Content: Crankshaft Balancer, Front Cover, Oil Fill Cap, Oil Pan, Oil Pump w/ ... Screen, Oil Pump Drive Shaft, and Valve Rocker Covers ... P3 (L29) MT1 Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, Valve ... Rocker Covers, and Harmonic Balancer Replaces: ... B7 (LP4)(L21) Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, Valve ... Rocker Covers, and Harmonic Balancer Replaces: ... | |
