Catalog: GM Goodwrench Engines Catalog | |
| Caps (valve) Gaskets All Cover Fuel Pump Opening Gear Balance Shaft Drive ( ... (if applicable) Nut-Connecting Rod Oil Fill Cap Nut Rocker Arm Stud Oil Pan ... Oil Pump Pushrods Pistons Pin and Rings ... Timing Chain Rotators (valve) Valve Oil Filter Bypass Shaft Distributor to Oil ... Pump Valves Inlet and Exhaust Valve ... | |
| the cover(s) if they are defective. Oil Pan Inspect the oil pan rail for ... bold holes. Check the front and rear oil pan seat rails for cracks or damage. If ... cracks are found replace the oil pan. Do not try to repair them. Inspect ... the oil drain plug for stripped threads or a ... , replace the cover. Mechanical Fuel Pump Clean the fuel pump and inspect the ... . Remember that mechanisms inside the pump wear. If the fuel pump has many miles ... | |
| disc will need to be inspected for oil contamination and excessive wear, such ... occur, replace the clutch disc. Water Pump It is recommended to replace the water ... pump when installing a new engine. However, ... if the old pump is reused, check for cavitation ... and smooth bearing feel. Replace the pump if it shows signs of wear. Spark Plug ... ) Inspect the distributor for signs of oil contamination. The drive gear should be ... , cracks and burrs. The distributor/oil pump drive should be free of nicks, burrs, ... conditioning compressor Power steering pump Sensors All pulleys and other bracketry ... | |
| replace them should not be overlooked. Oil Filters Oil Filters must always be ... prior to installing the new engine. Oil Pump, Pick-up Tube and Screen These ... prevent sludge, caused by gasses, and oil to build up in the crankcase. Spark ... and to clean silicates from the water pump shaft to prevent shaft seal damage. ... Fuel Filter Engine Oil Antifreeze Coolant Engine Oil Cooler ( ... | |
| and remove silicates from the water pump shaft that form from the coolant. ... the engine on an engine stand with the oil pan facing upwards, intake valley ... 's specifications. 1. Install the oil pump and the oil pump shaft. Fill the pump ... the initial suction and priming of the pump. Do not use white lithium grease to pack ... the oil pump. This grease won't breakdown and will ... clog oil passages, which could cause engine oil ... and seizing. 2. Install the new oil pick-up tube and screen and the ... crankshaft oil slinger. Be sure not to install the oil ... screen too close to the oil pan. Installing it too close can hinder ... the pick-up of oil causing oil starvation and seizing. Be sure to ... cover crankshaft seal with clean engine oil or E.O.S. Be sure to seal the bolts ... | |
| the intake valley is facing up and the oil pan is facing down. 9. Pour the ... with A.P.I. Starburst certified motor oil. Pre-lubing the engine is necessary to ... engine can be pre-lubed by priming the oil pump with a hand-held drill. Using an ... oil pump priming tool or distributor shaft, ... rotate the oil pump with a drill at 200 to 500 RPM for two ... manifold(s). 16. Install the fuel pump and fuel lines being sure of proper ... end bracketry Crankshaft pulley Water pump pulley Air conditioning compressor Air ... pump Alternator (generator) Power steering ... pump All sensors that were removed from the ... | |
| has been successfully installed and the oil pump has been primed, start the engine ... RPM for 10 to 20 minutes allowing the oil pressure and temperature to stabilize. ... the first service interval for changing oil and the oil filter should be between ... | |
| signs of engine failure causes: Serious oil or coolant leaks which may indicate ... of lubrication from using an incorrect oil, inadequate oil changes, a too-low oil ... , which may indicate excessive oil consumption, coolant hose/water pump ... | |
| engines have a recommended lubricant or oil type, certified by the American ... Institute (API). A Starburst certified oil is the recommended oil for vehicles. ... Containers for this oil have a "starburst" certification mark ... that makes it easier to select engine oils that meet performance standards set by ... . Containers of Starburst certified oil also have the standard API "donut" ... characteristics. Using the incorrect oil can lead to insufficient lubrication. ... Engines also have a recommended oil capacity and change interval. ... lubrication occurs when the oil level is below the minimum recommended ... of leakage or burn-off, or when the oil flow through the engine lubrication ... problems or sludge formation. The oil filter should be changed at the same ... time as the oil. If an engine failure is caused by lack ... | |
| Possible Cause Check or Test Low oil pressure Loose or plugged oil pick-up ... pressure switch or sensor Defective oil pressure gauge Incorrect oil viscosity ... Diluted oil Worn oil pump Plugged oil filter Excessive bearing clearances, ... , identify any other damage. Test oil pressure. Replace switch/sensor. Check ... with known good gauge. Change oil to specified; check pressure. Change ... oil. Inspect for contaminants (water, dirt, ... fuel, etc.) Check pump; replace as needed. Change oil; check ... pressure, engine operating. Check oil viscosity. Also check for contamination ... (s) ruptured Check for defective water pump, thermostat sticking closed, low ... | |
| dirty, defective lifters Defective fuel pump, pushrods Low oil pressure Worn valve ... inspection. Visual inspection. Check oil pressure; repair as needed. Perform ... ; use dial indicator to check wear. Oil drained out of lifters, replace as ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, Spark Plugs, and ... Water Pump INSTALLATION INSTRUCTIONS This engine ... all necessary components, such as oil fill tube and cap/indicator. Attach ... and add 4 quarts of Starburst certified oil of a viscosity recommended for your ... climate, and prime oil system. Check oil level on dipstick and add oil as ... to reach the full mark. CAUTION: The oil pump in this engine must be primed ... with the ignition system disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. ... Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, Spark Plugs, and ... Water Pump INSTALLATION INSTRUCTIONS This engine ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, P/S Pump Pulley, Spark ... Plugs, and Water Pump INSTALLATION INSTRUCTIONS This engine ... all necessary components, such as oil fill tube and cap/indicator. Attach ... and add 4 quarts of Starburst certified oil of a viscosity recommended for your ... climate, and prime oil system. Check oil level on dipstick and add oil as ... to reach the full mark. CAUTION: The oil pump in this engine must be primed ... with the ignition system disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. ... , Crankshaft Housing, Front Cover, Oil Check Valve, Oil Pan, Oil Pump w/ ... Screen, P/S Pump Pulley, Spark Plugs, Timing Chain ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, ... Spark Plugs, and Water Pump INSTALLATION INSTRUCTIONS This engine ... all necessary components, such as oil fill tube and cap/indicator. Attach ... and add 4 quarts of Starburst certified oil of a viscosity recommended for your ... climate, and prime oil system. Check oil level on dipstick and add oil as ... to reach the full mark. CAUTION: The oil pump in this engine must be primed ... with the ignition system disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. ... Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, ... Spark Plugs, and Water Pump INSTALLATION INSTRUCTIONS This engine ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, ... Spark Plugs, and Water Pump INSTALLATION INSTRUCTIONS This engine ... all necessary components, such as oil fill tube and cap/indicator. Attach ... and add 4 quarts of Starburst certified oil of a viscosity recommended for your ... climate, and prime oil system. Check oil level on dipstick and add oil as ... to reach the full mark. CAUTION: The oil pump in this engine must be primed ... with the ignition system disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. ... Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, ... Spark Plugs, and Water Pump INSTALLATION INSTRUCTIONS This engine ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, ... Spark Plugs, and Water Pump Replaces: 24574880 Replaced By: ... Notes: Does not contain Flywhl, Oil Fill Tube, C/case Vent Sys, Therm, Int ... Cr/shf Posn, Knock, Map, Cool Temp or Oil Lvl Sen. INSTALLATION INSTRUCTIONS ... applications. The mounting boss on the oil pan for the radiator outlet pipe ... engine requires transferring the water pump cover from the original engine. This is ... necessary to ensure that the water pump cover contains the nipple required for ... the heater hose. The water pump cover gaskets should be replaced at ... Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, ... Spark Plugs, and Water Pump Notes: Does not contain Flywhl, Oil ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, ... Spark Plugs, and Water Pump Notes: Does not contain Flywhl, Oil ... Cr/shf Posn, Knock, Map, Cool Temp or Oil Lvl Sen. INSTALLATION INSTRUCTIONS ... applications. The mounting boss on the oil pan for the radiator outlet pipe ... | |
| Content: Camshaft Housing, Front Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, ... Spark Plugs, and Water Pump Notes: Does not contain Flywheel, Oil ... Posn, Knock, Map, Cool Temp or Oil Level Sensor. Order 11516479 self ... Engine-Specific Content: Front Cover, Oil Check Valve, Oil Pan, Water Pump, and ... N (LD9) Engine-Specific Content: Oil Pan, Timing Chain Housing, Spark Plugs ... , Water Pump, and P/S Pump Pulley Notes: Does not include ... Ignition Module, Crankshaft Posn., and Oil Level Sensors. For 1 st design, see ... | |
| , Front Cover, Internal Balancer, Oil Pan, and Valve Rocker Cover ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| , Front Cover, Internal Balancer, Oil Pan, and Valve Rocker Cover ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| , Front Cover, Internal Balancer, Oil Pan, and Valve Rocker Cover ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan Notes: Must purchase balancer ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| -Specific Content: Front Cover and Oil Pan INSTALLATION INSTRUCTIONS The ... add 3 quarts of Starburst certified oil in viscosity suitable to your climate ... conditions. Prime system and check oil level on dipstick. Add oil as required ... area, replace the damper to prevent oil leaks. The rear most intake manifold ... for proper operation. CAUTION: The oil pump in this engine must be primed ... the coil or injector wire disconnected. Oil pressure warning light must go off (if ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| 8X) Engine-Specific Content: Flywheel, Oil Pan, Torsional Damper, and Valve Covers ... 8B) Engine-Specific Content: Flywheel, Oil Pan, Front Cover, Oil Fill Cap, ... hole with: 1 of 14064231 Cover Fuel Pump opening 2 of 11500914 Bolts 2 of ... | |
| .8S) A. Trans Engine-Specific Content: Oil Pan, Valve Covers, Flywheel, and ... . On "F" cars and "S" trucks: A) remove oil pan and replace with part number ... 10078999, B) remove oil pump screen assembly and replace with part ... number 10118624, C) use oil level indicator from replaced engine. ... . Trans (ML3) Engine-Specific Content: Oil Pan, Valve Covers, Flywheel, and ... . On "F" cars and "S" trucks: A) remove oil pan and replace with part number ... 10078999, B) remove oil pump screen assembly and replace with part ... number 10118624, C) use oil level indicator from replaced engine. ... | |
| -Specific Content: Front Cover and Oil Pump Notes: For "N" car applications, ... transfer oil filter adapter from old engine or order ... . Does not contain Rocker Covers, Oil Pan, Manifolds or Balancer. ... envelope) to clean valve covers. Oil Filter Adapters: For "N" car ... applications, transfer the oil filter adapter from the old engine or ... for 1992-93 models. CAUTION: The oil pump in this engine must be primed before ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12356520 ... -Specific Content: Front Cover and Oil Pump Notes: For "N" car applications, ... transfer oil filter adapter from old engine or order ... . Does not contain Rocker Covers, Oil Pan, Manifolds or Balancer. ... envelope) to clean valve covers. Oil Filter Adapters: For "N" car ... | |
| -Specific Content: Front Cover and Oil Pump Notes: For "N" car applications, ... transfer oil filter adapter from old engine or order ... . Does not contain Rocker Covers, Oil Pan, Manifolds or Balancer. ... envelope) to clean valve covers. Oil Filter Adapters: For "N" car ... applications, transfer the oil filter adapter from the old engine or ... for 1992-93 models. CAUTION: The oil pump in this engine must be primed before ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12356523 ... -Specific Content: Front Cover and Oil Pump Notes: For "N" car applications, ... transfer oil filter adapter from old engine or order ... . Does not contain Rocker Covers, Oil Pan, Manifolds or Balancer. ... envelope) to clean valve covers. Oil Filter Adapters: For "N" car ... | |
| ) Oldsmobile Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, and Valve ... U (LA1) NT3 Engine-Specific Content: Oil Pump, Front Cover, Oil Pan, Oil Filter ... , Valve Rocker Covers, Oil Level Sensor, Oil Fill Cap, and Lower ... N (LA1) Engine-Specific Content: Oil Pan, Oil Filter, and Rocker Covers ... When replacing a 2003MY engine, use the oil pan that corresponds with that ... W (LA1) Engine-Specific Content: Oil Pan, Oil Filter, and Rocker Covers ... When replacing a 2003MY engine, use the oil pan that corresponds with that ... | |
| , Filter, Level Indicator Assembly, Oil Level SW, Oil Pan, Flywheel, Spark ... Plugs, Engine Oil Additive, Water Pump/Pulley Assembly, Water Outlet, and ... -Specific Content: Balancer, Flywheel, Oil Pan, Oil Pump, and Oil Filter Notes: ... | |
| Content: Balance Shaft, Front Cover, Oil Filter Adapter, Oil Pump with Gears and ... : For "E" car applications, transfer oil filter adapter from old engine or order ... Engine does not include Rocker Covers, Oil Pan, Intake Manifold or Exhaust ... ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12360022 231 CID ... Content: Balance Shaft, Front Cover, Oil Filter Adapter, Oil Pump with Gears and ... : For "E" car applications, transfer oil filter adapter from old engine or order ... Engine does not include Rocker Covers, Oil Pan, Intake Manifold or Exhaust ... | |
| , Int Air Temp Sensor, Map Sensor, Oil Level Sensor, Oil Pressure Sensor, ... Spark Plugs, Themostat and Water Pump Notes: Does not include Intake ... ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12360686 231 CID ... -Specific Content: Front Cover and Oil Pump INSTALLATION INSTRUCTIONS Do not ... -87 "E" car applications, transfer the oil filter adapter from the old engine or ... new part number 25537239. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... | |
| Content: Balance Shaft, Front Cover, Oil Filter Adapter, Timing Chain Dampener, ... and Oil Pump INSTALLATION INSTRUCTIONS Do not ... -91 "E" car applications, transfer the oil filter adapter from the old engine or ... new part number 25537239. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12362214 231 CID ... Content: Balance Shaft, Front Cover, Oil Filter Adapter, Timing Chain Dampener, ... and Oil Pump INSTALLATION INSTRUCTIONS Do not ... 1992 "E" car applications, transfer the oil filter adapter from the old engine or ... and bolts 25519262. CAUTION: The oil pump in this engine must be primed before ... | |
| Content: Balance Shaft, Front Cover, Oil Filter Adapter, Timing Chain Dampener, ... and Oil Pump INSTALLATION INSTRUCTIONS Do not ... and "Z" car applications, transfer the oil filter adapter from the old engine or ... and studs 24500567. CAUTION: The oil pump in this engine must be primed before ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12362216 231 CID ... Content: Balance Shaft, Front Cover, Oil Filter Adapter, Timing Chain Dampener, ... and Oil Pump INSTALLATION INSTRUCTIONS Do not ... and "Z" car applications, transfer the oil filter adapter from the old engine or ... and studs 24500567. CAUTION: The oil pump in this engine must be primed before ... | |
| Content: Balance Shaft, Front Cover, Oil Filter Adapter, Timing Chain Dampener, ... and Oil Pump INSTALLATION INSTRUCTIONS Do not ... and "Z" car applications, transfer the oil filter adapter from the old engine or ... and studs 24500567. CAUTION: The oil pump in this engine must be primed before ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12362218 231 CID ... Content: Balance Shaft, Front Cover, Oil Filter Adapter, Timing Chain Dampener, ... and Oil Pump INSTALLATION INSTRUCTIONS Do not ... ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... | |
| Content: Balance Shaft, Front Cover, Oil Filter Adapter, Oil Pump w/Gears, ... Timing Chain Dampener, and Oil Pump Notes: 1 st design has 5/16" oil pan ... ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12362221 231 CID ... Content: Balance Shaft, Front Cover, Oil Filter Adapter, Oil Pump w/Gears, ... Timing Chain Dampener, and Oil Pump Notes: *2 nd design has 1/4" Oil Pan ... ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... | |
| 8K) Engine-Specific Content: Flywheel, Oil Pan, Lower Intake Manifold, Front Cover ... , Water Pump, Balancer, and Crank Cam Posn. Sensors ... ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12482057 231 CID ... -Specific Content: Balancer, Flywheel, Oil Pan, Front Cover, Oil Filter, Lower ... Covers, Crank Cam Posn. Sensors, and Oil Level Sensor Replaces: 12568293 ... ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... | |
| ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 89017667 231 CID ... , Lower Intake Manifold, Valve Covers, Oil Level Sensor, Oil Pan, and Water Pump ... parts. May be necessary to replace Oil Level Sensor with new or Trans ... ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| Content: Crank Balancer, Flywheel, Oil Pan, Front Cover, Oil Filter, Lower ... Covers, Crank Cam Posn. Sensor, and Oil Level Sensor Replaces: 12480889, ... ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... owner's manual for proper oil type and quantity. DA MAGE WILL RESULT ... IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 89017670 231 CID ... Content: Crank Balancer, Flywheel, Oil Pan, Front Cover, Oil Filter, Lower ... Covers, Crank Cam Posn. Sensor, and Oil Level Sensor Replaces: 12480889, ... ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Refer to ... | |
| (LB1)(4.3N) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| . GVW (NA4) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| . GVW (NA4) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12361248 ... (L35)(4.3W) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... | |
| (LB4)(4.3Z) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12361251 ... (LB4)(4.3Z) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... | |
| B (LB4)(4.3Z) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12361253 ... (L35)(4.3W) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... | |
| )(4.3Z) M30 Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... Pressure Bypass Valve. Does not include Oil Pan or Rocker Covers, order separately ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12363729 ... )(4.3Z), M30 Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... | |
| (exc. CTF) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12366016 ... M30 (A/Trans) Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... | |
| LM1 (L35) M30 Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12369214 ... MTI, NA4, ZK3 Engine-Specific Content: Oil Pump Notes: Includes 21-PSI Oil ... the first service interval including an oil and filter change should be between 300 ... | |
| Engine-Specific Content: Front Cover, Oil Fill Cap, Oil Pan, Oil Pump w/Screen, ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| Engine-Specific Content: Front Cover, Oil Fill Cap, Oil Pan, Oil Pump w/Screen, ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| LM1 (L35) Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, and Valve ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| LF6) M30, M50 Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, and Valve ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 88893276 ... GMC T1 (LF6) Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, and Valve ... INSTALLATION INSTRUCTIONS CAUTION: The oil pump in this engine must be primed ... | |
| : Harmonic Balancer, Balance Shaft, Oil Pan, Front Cover, and Rocker Covers ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 89017321 ... -Specific Content: Light Duty Shallow Oil Pan, Oil Pump, Front Cover, and Rocker ... , 88894116 Replaced By: Notes: Swap Oil Pan from original engine or buy new ( ... | |
| -Specific Content: Light Duty Deep Oil Pan, Harmonic Balancer, Front Cover, ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 89017324 ... LU3) M50, M30 Engine-Specific Content: Oil Pump, Front Cover, and Rocker Covers ... LU3) M30, ZR2 Engine-Specific Content: Oil Pump, Front Cover, and Rocker Covers ... | |
| Engine-Specific Content: Front Cover, Oil Fill Cap, Oil Pan, Oil Pump w/Screen, ... the first service interval including an oil and filter change should be between 300 ... and 500 miles. Replacement of oil related parts: If the original engine ... or due to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... do so will usually result in increased oil consumption by allowing oil from the ... holes empty into cylinder #3 and #4, oil fouling will be greater on the spark ... must also be transferred. CAUTION: The oil pump in this engine must be primed ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ... | |
| ST1 (LL8) Engine-Specific Content: Oil Filter, Oil Pan, Water Pump, Spark ... , the Spark Plugs, Knock Sensors and Oil Pan must be changed to 2002 parts. ... | |
| : Drive Belt Tensioner, Front Cover, Oil Filter, Oil Level Sensors, Oil Press ... Sensor, Oil Pump w/Screen, and Water Pump w/Pulley Notes: Exc. Intake and ... : Drive Belt Tensioner, Front Cover, Oil Filter, Oil Level Sensors, Oil Press ... Sensor, Oil Pump w/Screen, Water Pump w/Pulley, and Balancer Notes: Exc. ... | |
| ) (exc. KL5) Engine-Specific Content: Oil Pan, Water Pump, Oil Pump, and Timing ... ) Natural Gas Engine-Specific Content: Oil Pan, Water Pump, Oil Pump, and Timing ... | |
| Balancer, Front Cover, Flywheel, Oil Filter w/Adapter, Oil Pan, Oil Pump, ... Plugs, Thermostat Housing, and Water Pump w/Pulley Notes: Replaces: Replaced ... Covers, Crankshaft Balancer, Engine Oil Manifold, Front Cover, Flywheel, Oil ... Fill Cap, Oil Filter w/Adapter, Oil Level Indicator Tube Assembly, Oil ... Level Sensor, Oil Pan, Oil Pump Suction Pipe, PCV Valve, Spark Plugs, ... Sensor, Thermostat Housing, Water Pump w/Housing, and Water Pump w/Pulley ... 1998 KS/KY models transfer or purchase Oil Level Indicator and Tube. 1995-97 ... models transfer or purchase Oil Filter Adapter (with oil clr ports). ... Covers, Crankshaft Balancer, Engine Oil, Front Cover, Flywheel, Oil Fill Cap, ... Oil Filter w/Adapter, Oil Pan, Oil Pump, and PCV Valve Notes: On 1995-97 models ... | |
| Balancer, Front Cover, Flywheel, Oil Filter w/Adapter, Oil Pan, Oil Pump, ... Spark Plugs, Thermostat Housing, Water Pump w/Pulley, and Engine Oil Replaces: ... | |
| : Front Cover, Harmonic Balancer, Oil Pan, and Oil Filter Replaces: ... : Front Cover, Harmonic Balancer, Oil Pan, and Oil Filter Replaces: ... -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, Water Pump and Rocker ... -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, Water Pump and Rocker ... -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, Water Pump and Rocker ... | |
| Engine-Specific Content: Front Cover, Oil Fill Cap, Oil Pan, and Valve Rocker ... -Specific Content: Crankshaft, Inj Pump Drive, Oil Pump w/Screen, Conn. Rod and ... Notes: Engine does not include Water Pump, Intake or Exhaust Manifold, Flywheel, ... Front Cover or Oil Pan. Replaces: 22536528 Replaced By ... : INSTALLATION INSTRUCTIONS Oil Pump Screen Height: The oil pump pickup ... engine. Prior to reinstallation of the oil pan, check the location of the screen. ... Oil Pump: On all "E" or "K" models, remove the ... oil pump from the old engine. If the engine ... , it is suggested you purchase a new oil pump. If it is low mileage and the oil ... pump worked well, transfer the pump from the old engine. Failure to change ... the pump will result in oil starvation because of the pickup screen ... | |
| : Front Cover, Harmonic Balancer, Oil Pan, Oil Filter, and Valve Rocker ... : Front Cover, Harmonic Balancer, Oil Pan, Oil Filter, and Valve Rocker ... -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, Water Pump, and ... ST1 (LM4) M30 Engine-Specific Content: Oil Pump, Front Cover, Water Pump, and ... | |
| Engine-Specific Content: Front Cover, Oil Pan, and Valve Covers Notes: Refer to ... : Front Cover, Harmonic Balancer, Oil Filter, Oil Pan, Intake Manifold, Fuel ... Rail, and Water Pump Replaces: Replaced By: 88894382 ... | |
| : Front Cover, Harmonic Balancer, Oil Filter, Oil Pan, Intake Manifold, Fuel ... Rail, and Water Pump Replaces: Replaced By: 88890543 ... -Specific Content: Crankshaft Hub, Oil Pan, and Valve Rocker Cover ... is built with 1993 model year designed oil pan (no rail bead) and oil pan gasket ... . On "D" car models 1992 prior, remove oil pan and replace with original or with ... | |
| Engine-Specific Content: Front Cover, Oil Pan, Torsional Damper, and Valve Rocker ... is built with 1993 model year designed oil pan (no rail bead), oil pan gasket, ... and oil pump assembly. When servicing this engine, ... engine. On models with a 5-Quart Oil Pan, remove oil pan and oil pump ... assembly. Replace with original or new oil pan assembly part number 12518043, oil ... pump assembly part number 10168529, and ... screen oil part number 10166159. This engine is ... Content: Crankshaft Hub, Front Cover, Oil Pan, and Valve Rocker Cover Notes: For ... Content: Crankshaft Hub, Front Cover, Oil Pan, and Valve Rocker Covers Notes: ... | |
| Engine-Specific Content: Front Cover, Oil Pan, Oil Pump w/Shaft and Cover, Water ... Pump w/Shaft and Cover Notes: Does not ... Manifold, Starter, Flywheel, Water Pump, Ignition or Attaching Parts Replaces ... Content: Front Cover and Pointer, Oil Pan, Torsional Damper, and Valve Rocker ... GMC W4 (L31) Engine-Specific Content: Oil Pan Notes: For 2001 application, must ... | |
| , GMC W4 Engine-Specific Content: Oil Pan INSTALLATION INSTRUCTIONS No ... : Front Cover, Harmonic Balancer, Oil Filter, Oil Pan, Intake Manifold, Fuel ... Rail, and Water Pump Replaces: Replaced By: 88890544 ... : Front Cover, Harmonic Balancer, Oil Filter, Oil Pan, Intake Manifold, Fuel ... Rail, and Water Pump Replaces: 12457659 Replaced By: ... : Front Cover, Harmonic Balancer, Oil Filter, Oil Pan, Intake Manifold, Fuel ... Rail, and Water Pump Replaces: 12455110 Replaced By: ... | |
| Engine-Specific Content: Front Cover, Oil Pan, Oil Pump w/Shaft and Cover, Water ... Pump w/Shaft and Cover Notes: Does not ... Content: Crankshaft Hub, Front Cover, Oil Pan, and Valve Rocker Cover Replaces: ... On "Y" car applications, valve covers, oil pan, and oil pump screen must be ... Covers (w/gasket) Valve Cover Bolts Oil Pump Screen Oil Pan Kit/Pan Gasket ... 'press' after installing the oil pump screen,replace oil pump with part ... | |
| Content: Crankshaft Hub, Front Cover, Oil Pan, and Valve Rocker Cover Replaces: ... On "Y" car applications, valve covers, oil pan, and oil pump screen must be ... Year Valve Covers Valve Cover Bolts Oil Pump Screen Oil Pan Kit/Pan Gasket ... 'press' after installing the oil pump screen,replace oil pump with part ... Engine-Specific Content: Front Cover, Oil Pan, Oil Pump w/Shaft and Cover, Water ... Pump w/Shaft and Cover Notes: Does not ... Manifold, Starter, Flywheel, Water Pump, Ignition or Attaching Parts Replaces: ... On "Y" car applications, valve covers, oil pan, and oil pump screen must be ... Covers (w/gasket) Valve Cover Bolts Oil Pump Screen Oil Pan Kit/Pan Gasket ... 'press' after installing the oil pump screen,replace oil pump with part ... | |
| -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, Water Pump, and ... -Specific Content: Harmonic Balancer, Oil Pan, Oil Pump, Front Cover, Water Pump ... -Specific Content: Harmonic Balancer, Oil Pan, Oil Pump, Front Cover, Water Pump ... -Specific Content: Harmonic Balancer, Oil Pan, Oil Pump, Front Cover, Water Pump ... | |
| -Specific Content: Harmonic Balancer, Oil Pan, Oil Pump, Front Cover, Water Pump ... | |
| seals and gaskets. Install the supplied oil pump and transfer all necessary ... components including oil pan, and valve covers to the ... sensor. It may be necessary to tap the oil tube-mounting hole with 1/4-18 dry-seal ... leaks. On certain models with shallow oil pan, a new oil pump assembly, part ... tube must be installed in place of the pump supplied with this engine. Attach two ... ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Use 6 ... quarts of A.P.I. Starburst certified oil in the viscosity suitable for your ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED PROPERLY ... : Front Cover, Harmonic Balancer, Oil Filter, Oil Pan, and Valve Covers ... | |
| 12465229 366 CID New Electric Fuel Pump Application Only 6.0L 1986-89 ... Chevrolet, GMC M4,5,6 (L86) MF1 (exc. oil cooler KPS, air comp application) 1986 ... , GMC B6 (L86) 366 (LS0) MF1 (exc. oil cooler KPS, air comp application) 1990 ... GMC B7 (LS0) Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, Valve ... Rocker Covers Notes: Electric Fuel Pump Application Only. When replacing ... , must also use 1-12529747 water pump. Replaces: 12530366 Replaced By: ... | |
| 88890535 366 CID New Mechanical Fuel Pump Application Only 6.0L 1986-89 ... Chevrolet, GMC M4,5,6 (L86) MF1 (exc. oil cooler KPS, air comp application) 1986 ... , GMC C6,7 (L86) ME4, ME6 (exc. oil cooler application (with kit 15637482 ... , GMC B6 (L86) 366 (LS0) M.T. (exc. oil cooler KPS, air comp application) 1989 ... , GMC B6 (L86) 366 (LS0) MF1 (exc. oil cooler KPS, air comp application) 1989 ... F6,7 (LS0) Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, Valve ... Rocker Covers Notes: Mechanical Fuel Pump Application Only. When replacing ... , must also use 1- 12529747 water pump. Replaces: 12530366 Replaced By: ... | |
| -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, and Water Pump ... : Front Cover, Harmonic Balancer, Oil Filter, Oil Pan, and Valve Covers ... : Front Cover, Harmonic Balancer, Oil Filter, Oil Pan, and Valve Covers ... -Specific Content: Harmonic Balancer, Oil Pan, Front Cover, and Water Pump ... | |
| seals and gaskets. Install the supplied oil pump and transfer all necessary ... components including oil pan and valve covers to the ... sensor. It may be necessary to tap the oil-tube mounting hole with 1/4-18 dry-seal tap ... leaks. On certain models with shallow oil pan, a new oil pump assembly, part ... tube must be installed in place of the pump supplied with this engine. Attach two ... ) to clean valve covers. CAUTION: The oil pump in this engine must be primed ... priming procedures. Also, check engine oil level before starting engine. Use 6 ... quarts of Starburst certified oil in the viscosity suitable for your ... RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. ... | |
| MF1, MT9, IMT9 *indicates kit includes oil cooling. Oil Cooling Kit Model Year ... 15662081 C6,7 1986-90 LR0, L43 w/oil cooling 15662081 P6 1986-90 L43 w/ ... trucks, you must purchase a new water pump and lower radiator hose. For 1990 and ... prior, you must replace the water pump with part number 12529747 to clear the ... 8" damper. Year Water Pump Hoses Usage 1991-94 12529192 ... | |
| and 77-85 P3 (42) models, a new shallow oil pump, p/n 14067529, must be installed ... and 77-85 P3 (42) models, a new shallow oil pump, p/n 14067529, must be installed ... 1985 P3 (42) models have shallow oil pan. For these models, new pump part ... must be installed in place of the pump supplied with the engine. 1990 ... 7.4L) Notes: On vehicles with shallow oil pan design, a new oil pump, p/n ... | |
| : Crankshaft Balancer, Front Cover, Oil Fill Cap, Oil Pan, Oil Pump w/Screen, ... Oil Pump Drive Shaft, Valve Rocker Cover Notes ... : Does not use old oil adapter. Cooler lines go to block. ... 15637099 G3 1988-90 All (w/Oil Cooling) 15637100 P3 (32) 1974-90 w ... w/A.T. 15637108 K3 1974-86 w/A.T. Oil Cooling Kit Model Year Restriction ... -86 KC4 15637110 K3 1974-82 KC4* *oil cooler part number 3053355 is required ... | |
| : Crankshaft Balancer, Front Cover, Oil Fill Cap, Oil Pan, Oil Pump w/Screen, ... Oil Pump Drive Shaft, and Valve Rocker Covers ... P3 (L29) MT1 Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, Valve ... B7 (LP4)(L21) Engine-Specific Content: Oil Pan, Oil Filter, Front Cover, Valve ... | |
