Catalog: GM Goodwrench Engines Catalog | |
| surfaces on new and remanufactured engines and/or cleaning parts from the failed ... engine to be reused, the use of surface ... TM, Soc Att TM, ABRASIVE DISCS) If the original engine failed either catastrophically ... or due to bearing failure, the engine oil cooler must be replaced. If the ... these repairs will void your Goodwrench Engine Warranty. Before installing any engine ... , verify that you have the correct engine for the application. Refer to the ... , air purge and fluid volumes). Some engines have been remanufactured subsequent to ... design refinements not included in the original service information (i.e., 1989 engines ... If future service is necessary for the engine, consult the GM Parts Catalog, GM Part ... | |
| III Page 9 August 2004 TRANSFERABLE ENGINE COMPONENTS Take out the old engine, ... mount it on an engine stand, and carefully remove those ... that are to be transferred to the new engine. The following list of components should ... are damaged or were the cause of the original engine failure, they should be replaced ... thoroughly before placing it on the new engine. Any foreign objects within the intake ... , heads and other vital parts of the engine. Warning Do not use any form of blasting ... | |
| Page 11 August 2004 NON-TRANSFERABLE ENGINE COMPONENTS Some components off the old ... engine will not be able to be used on the new ... replacement engine. This is because they will hinder the ... performance of the engine if they are not replaced. Or, they are ... The thermostat previously used in the original engine may be clogged or is worn out. ... replaced prior to installing the new engine. Oil Pump, Pick-up Tube and Screen These ... components come with the new engine. PCV Valve and Crankcase Breather Filter ... that the emission standards of the engine are met and to prevent sludge, caused ... proper heat range for the vehicle and engine application. Failure to change the ... a choke and affect fuel consumption and engine performance. Cooling System Sealing ... prevent shaft seal damage. Fuel Filter Engine Oil Antifreeze Coolant Engine Oil ... | |
| PROCEDURES cont. 8. Rotate the engine on the engine stand so that the intake ... and camshaft. 10. Pre-lube the engine with A.P.I. Starburst certified motor ... oil. Pre-lubing the engine is necessary to avoid dry start damage ... The most efficient way to pre-lube the engine is to use the J-45299 engine pre-luber ... on all applications. However, if no engine pre-luber is available and the engine ... has a mechanical distributor, the engine can be pre-lubed by priming the oil ... after pressure builds up in the engine. This is to flush any debris from the ... engine without a load on the bearings while ... seal properly to avoid damage to the engine. Refer to the service manual for that ... All sensors that were removed from the original engine Engine mounts (engine to frame) ... | |
| GENERAL ENGINE DIAGNOSTICS Section IV Page 21 August ... or Detonation Diagnosis With normal engine operation, the combustion process is ... power. Today's internal combustion engines operate on a basic four-stroke cycle: ... to about one-eighth or ninth of its original volume. Power: The spark plug fires, ... four-stroke cycle takes place in each engine cylinder according to a certain ... a smooth power flow results in optimum engine performance. The long-term effects of ... off. The common owner concern is engine "knocking". Uncorrected, the damage can ... be significant and require an engine replacement. Such damage can include ... or carbon deposits removed using an engine cleaner. If the engine failure has ... system repairs are needed. Replacing an engine without correcting the failure cause ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 35 August 2004 ... 2.3A) 1990 Oldsmobile W (LG0)(2.3A) Engine-Specific Content: Camshaft Housing, Front Cover ... Pump INSTALLATION INSTRUCTIONS This engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1989 engines ... If future service is necessary for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... repair procedures. After removing old engine, use new seals and gaskets and transfer ... tube and cap/indicator. Attach Quad IV engine decal (enclosed in instruction envelope ... ). Install replacement engine and add 4 quarts of Starburst certified ... mark. CAUTION: The oil pump in this engine must be primed before starting. Crank ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 36 August 2004 ... Pontiac, Chevrolet N (LG0)(2.3A) Engine-Specific Content: Camshaft Housing, Front Cover ... Pump INSTALLATION INSTRUCTIONS This engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1989 engines ... If future service is necessary for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... repair procedures. After removing old engine, use new seals and gaskets and transfer ... tube and cap/indicator. Attach Quad IV engine decal (enclosed in instruction envelope ... ). Install replacement engine and add 4 quarts of Starburst certified ... mark. CAUTION: The oil pump in this engine must be primed before starting. Crank ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 37 August 2004 ... , Oldsmobile, N (LD2)(2.3D) Buick Engine-Specific Content: Camshaft Housing, Front Cover ... Pump INSTALLATION INSTRUCTIONS This engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1989 engines ... If future service is necessary for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... repair procedures. After removing old engine, use new seals and gaskets and transfer ... tube and cap/indicator. Attach Quad IV engine decal (enclosed in instruction envelope ... ). Install replacement engine and add 4 quarts of Starburst certified ... mark. CAUTION: The oil pump in this engine must be primed before starting. Crank ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 38 August 2004 ... Pontiac, Oldsmobile N (LD2)(2.3D) Engine-Specific Content: Camshaft Housing, Front Cover ... Pump INSTALLATION INSTRUCTIONS This engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1989 engines ... If future service is necessary for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... repair procedures. After removing old engine, use new seals and gaskets and transfer ... tube and cap/indicator. Attach Quad IV engine decal (enclosed in instruction envelope ... ). Install replacement engine and add 4 quarts of Starburst certified ... mark. CAUTION: The oil pump in this engine must be primed before starting. Crank ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 39 August 2004 ... Pontiac, Oldsmobile N (LG0)(2.3A) Engine-Specific Content: Camshaft Housing, Front Cover ... for adapting current model Goodwrench engines into past model applications. The ... require attachment on the Goodwrench engine. LG0 (2.3A) engines may require ... crankshaft balancer on the Goodwrench engine is the same diameter as the original ... balancer. If not, transfer the original balancer to the Goodwrench engine. ... Supreme with LD2 (2.3D) or LG0 (2.3A) engines require an M12 x 1.75 bolt (part ... along with the two included M12 x 1.75 engine lift bracket bolts, to attach the ... engine mount strut bracket to the engine drill out the hole (12.5MM) on the ... bolt 22579611 is included in service engine installation kit, catalog group 0.010 ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 42 August 2004 ... Buick 1990 Chevrolet W (LR8)(2.5R) Engine-Specific Content: Crankshaft Balancer, Front ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 43 August 2004 ... Buick 1986 Chevrolet P (LR8)(2.5R) Engine-Specific Content: Crankshaft Balancer, Front ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 44 August 2004 ... 1985 Chevrolet, Buick X (LR8)(2.5R) Engine-Specific Content: Crankshaft Balancer, Front ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 45 August 2004 ... , Buick 1984 Pontiac P (LR8)(2.5R) Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 46 August 2004 ... A, X (LR8)(2.5R) Oldsmobile, Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 47 August 2004 ... , Oldsmobile N (L68)(2.5U) Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 48 August 2004 ... , Oldsmobile N (L68)(2.5U) Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 49 August 2004 ... N (L68)(2.5U) w/M.T. Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 50 August 2004 ... N (L68)(2.5U) w/A. Trans Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 51 August 2004 ... , Oldsmobile N (L68)(2.5U) Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 52 August 2004 ... , Oldsmobile S1 (LN8)(2.5E) GMC Engine-Specific Content: Front Cover and Oil Pan Notes ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 53 August 2004 ... , GMC M1, ST1, Z1 (LN8)(2.5E) Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 54 August 2004 ... 1986 Chevrolet M1, ST1 (LN8)(2.5E) Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 55 August 2004 ... 1985 Chevrolet M1, ST1 (LN8)(2.5E) Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 56 August 2004 ... , Buick 1988 Pontiac P (LR8)(2.5R) Engine-Specific Content: Front Cover INSTALLATION ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 57 August 2004 ... , Oldsmobile, N (L68)(2.5U) Buick Engine-Specific Content: Front Cover INSTALLATION ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 58 August 2004 ... 1991 Oldsmobile, Buick N (L68)(2.5U) Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 59 August 2004 ... GMC 1991-93 GMC Z1 (LLV)(L38)(2.5A) Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 60 August 2004 ... , A (LR8)(2.5R) Oldsmobile, Buick Engine-Specific Content: Front Cover and Oil Pan ... INSTRUCTIONS The Goodwrench 2.5 engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts and ... revisions. Before installing this engine, refer to the appropriate vehicle ... necessary components to the replacement engine. Thoroughly clean all old parts to ... manifold bolt MUST go through the engine lift bracket or an equivalent thickness ... lifter noise and possible damage to the engine. Rocker cover installation: A) use RTV ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 72 August 2004 ... Oldsmobile, Buick A, N (LG7)(3.3N) Engine-Specific Content: Front Cover and Oil Pump ... , transfer oil filter adapter from old engine or order new as detailed in the ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3300 engine decals (enclosed in instructions ... the oil filter adapter from the old engine or use new part number 25537239 for ... models. CAUTION: The oil pump in this engine must be primed before starting. DAMAGE ... WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... Oldsmobile, Buick A, N (LG7)(3.3N) Engine-Specific Content: Front Cover and Oil Pump ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 73 August 2004 ... )(3.3N) 1992 Pontiac N (LG7)(3.3N) Engine-Specific Content: Front Cover and Oil Pump ... , transfer oil filter adapter from old engine or order new as detailed in the ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3300-engine decals (enclosed in instructions ... the oil filter adapter from the old engine or use new part number 25537239 for ... models. CAUTION: The oil pump in this engine must be primed before starting. DAMAGE ... WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... )(3.3N) 1993 Pontiac N (LG7)(3.3N) Engine-Specific Content: Front Cover and Oil Pump ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 79 August 2004 ... )(3.8C) 1989 Pontiac H (LN3)(3.8C) Engine-Specific Content: Balance Shaft, Front Cover, ... , transfer oil filter adapter from old engine or order new. Engine does not include ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... )(3.8C) 1990 Pontiac H (LN3)(3.8C) Engine-Specific Content: Balance Shaft, Front Cover, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 80 August 2004 ... , Oldsmobile H (LN3)(3.8C) Buick Engine-Specific Content: Crankshaft Balancer, Crank and ... Cam Posn Sensor, Engine Coolant Temp Sensor, Front Cover, Int ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... , Buick A, C, E, H (LG2)(3.8B) Engine-Specific Content: Front Cover and Oil Pump ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 81 August 2004 ... Pontiac, Oldsmobile, H (L27) Buick Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... the oil filter adapter from the old engine or use new part number 25537239. ... CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... , U Van (L27)(3.8L) Oldsmobile Engine-Specific Content: Balance Shaft, Front Cover, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 82 August 2004 ... , U Van (L27)(3.8L) Oldsmobile Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... the oil filter adapter from the old engine or use new part number 24501300 and ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... , U Van (L27)(3.8L) Oldsmobile Engine-Specific Content: Balance Shaft, Front Cover, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 83 August 2004 ... , U Van (L27)(3.8L) Oldsmobile Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... the oil filter adapter from the old engine or use new part number 24501300 and ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... )(3.8L) 1992 Pontiac H (L67)(3.8L) Engine-Specific Content: Balance Shaft, Front Cover, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 84 August 2004 ... Buick C (L67) 1994 Pontiac H (L67) Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... )(3.8-1) 1995 Buick G (L67)(3.8-1)* Engine-Specific Content: Balance Shaft, Front Cover, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 85 August 2004 ... 2000-04 Pontiac, Buick H (L36)(3.8K) Engine-Specific Content: Flywheel, Oil Pan, Lower ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... 2000-04 Buick C (L67)(3.8-1) SFI, SC Engine-Specific Content: Balancer, Flywheel, Oil Pan, ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 86 August 2004 ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... 1) 2004-05 Chevrolet W (L67)(3.8-1) Engine-Specific Content: Balancer, Crank Cam Posn. ... Oil Level Sensor with new or Trans Original Sens. Engine comes with 97-00 Flywheel ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 87 August 2004 ... New 3.8L 2005 Chevrolet W (L26) Engine-Specific Content: Crank Balancer, Flywheel, Oil ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... original engine. Identification of the engine being installed must comply with any ... . Goodwrench Decals: Attach two 3800-engine decals (enclosed in instructions ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Refer ... and quantity. DA MAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... 3.8L 2004 Pontiac, Buick W (L26) Engine-Specific Content: Crank Balancer, Flywheel, Oil ... INSTRUCTIONS Do not remove the engine vehicle identification plate from the ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 88 August 2004 ... , GMC C1,2 G1,2 K1, M1 (LB1)(4.3N) Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 89 August 2004 ... 3Z) Exc. Emis. above 8500lb. GVW (NA4) Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 90 August 2004 ... 3Z) Exc. Emis. above 8500lb. GVW (NA4) Engine-Specific Content: Oil Pump Notes: Includes 21- ... PSI Oil Pressure Bypass Valve. Engine not used on GMC Typhoon and Syclone ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 91 August 2004 ... 1993 Chevrolet, GMC ST1 (LB4)(4.3Z) Engine-Specific Content: Oil Pump Notes: Includes 21- ... PSI Oil Pressure Bypass Valve. Engine not used on GMC Typhoon and Syclone ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 92 August 2004 ... 4.3L 1993 Chevrolet B (LB4)(4.3Z) Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... Chevrolet, GMC LM1, ST1 (L35)(4.3W) Engine-Specific Content: Oil Pump Notes: Includes 21- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 93 August 2004 ... Chevrolet, GMC LM1 (LB4)(4.3Z) M30 Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... Chevrolet, GMC G1,2 (LB4)(4.3Z), M30 Engine-Specific Content: Oil Pump Notes: Includes 21- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 94 August 2004 ... ST1 (06-16)(L35)(4.3W) M30 (exc. CTF) Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... Sys (under 8500lb. GVM) M30 (A/Trans) Engine-Specific Content: Oil Pump Notes: Includes 21- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 95 August 2004 ... ) 1995 Chevrolet, GMC LM1 (L35) M30 Engine-Specific Content: Oil Pump Notes: Includes 21- ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... , GMC G2,3 (L35) MTI, NA4, ZK3 Engine-Specific Content: Oil Pump Notes: Includes 21- ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 96 August 2004 ... )(4.3A) Emis. above 8500lb. GVW (NA4) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Rocker Cover Notes: *Effective with engine codes ADF, AJZ, FLX, and XDF. ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 97 August 2004 ... , GMC G1,2 (L35) M30, NA1 (exc. ZK3) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... replacing a 1998 and prior Goodwrench engine (12532552), also use 1-12557587 ... flywheel when replacing a Goodwrench engine (12532552) for P3 application. ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 98 August 2004 ... 1996-2000 Chevrolet, GMC LM1 (L35) Engine-Specific Content: Oil Pan, Oil Filter, Front ... Notes: When replacing a 1998 and prior engine, also use 1-12557587 flywheel for A. ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 99 August 2004 ... -99 Chevrolet, GMC S1 (LF6) M30, M50 Engine-Specific Content: Oil Pan, Oil Filter, Front ... Notes: When replacing a 1998 and prior engine, also use 1-12557587 flywheel for A. ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 100 August 2004 ... Chevrolet, GMC G2,3 (L35)(4.3W) MT1 Engine-Specific Content: Harmonic Balancer, Balance ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... ) M30 2002 Chevrolet, GMC CK1 (LU3) Engine-Specific Content: Light Duty Shallow Oil Pan, ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 101 August 2004 ... ) M30 2002 Chevrolet, GMC LM1 (LU3) Engine-Specific Content: Light Duty Deep Oil Pan, ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... DAMAGE WILL RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... Chevrolet, GMC S1 (LU3) M50, M30 Engine-Specific Content: Oil Pump, Front Cover, and ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 102 August 2004 ... , GMC G2,3 (L35) MT1, NA4 (exc. ZK3) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Notes: When replacing a 1998 prior GW engine (12369214), also use flywheel (12557584 ... of oil related parts: If the original engine failed either catastrophically or due ... to bearing failure, the engine oil cooler MUST BE REPLACED and the oil ... Brite) is the number one cause of 4.3L engine failure. Intake Manifold: For some ... engine assemblies (see service manual), sealer ... consumption by allowing oil from the engine valley to be drawn into the intake ... bolt plastic covers. On OBD II equipped engines, reluctor ring must also be transferred ... . CAUTION: The oil pump in this engine must be primed before starting engine. ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 112 August 2004 ... .0H) 1991-92 Cadillac D (L03)(5.0H) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... Cover INSTALLATION INSTRUCTIONS This engine is built with 1993 production ... components. When servicing engine, use 1993 service parts. For "D" and "F ... pan and replace with pan from replaced engine or order oil pan kit, part number ... W thread sealer, part number 12345493. Engine built after 04/13/94 have roller timing ... bolt part number 9417950 must be used. Engines built with link timing chain must use ... and bolt part number 3874878. This engine is built to production point of build ... -95 Chevrolet, GMC CK1,2 (L03)(5.0H) Engine-Specific Content: Front Cover, Oil Fill Cap, Oil ... By: INSTALLATION INSTRUCTIONS This engine is built with 1993 production ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 116 August 2004 ... 5.7L 1999 Chevrolet Y (LS1)(5.7G) Engine-Specific Content: Front Cover, Harmonic Balancer ... 5.7K) 1992 Oldsmobile B (L05)(5.7K) Engine-Specific Content: Crankshaft Hub, Oil Pan, and ... Part number 12513151 5.7 Liter engine is built with 1993 model year designed ... oil pan gasket. When servicing this engine, it is required that replacement parts ... prior, remove oil pan and replace with original or with new part number 12518044. ... Engines built after 04/13/94 have roller timing ... 14088783 and bolt part number 9417950. Engine built with link timing chain must use ... and bolt part number 3874878. This engine is built to production point of build ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 117 August 2004 ... (L05)(5.7K) MT1, 9C2, 5Z1 (exc. NM8) Engine-Specific Content: Front Cover, Oil Pan, ... 12520270 5.7 Goodwrench 5.7 Liter engine is built with 1993 model year designed ... oil pump assembly. When servicing this engine, it is required that replacement parts ... be of the same type and design. This engine is built with current-production valve ... be necessary to use cover from replaced engine. On models with a 5-Quart Oil Pan, ... pan and oil pump assembly. Replace with original or new oil pan assembly part number ... screen oil part number 10166159. This engine is built to production point of build ... Chevrolet, GMC G1,2 (L31)(5.7R) M30 Engine-Specific Content: Crankshaft Hub, Front Cover, ... : For 2001 G-van application, service engine block contains English threads. May ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 120 August 2004 ... )(5.7P) 1996 Cadillac B (LT1)(5.7P) Engine-Specific Content: Front Cover, Oil Pan, Oil Pump ... 5.7P) 1995 Chevrolet Y (LT1)(5.7P) Engine-Specific Content: Crankshaft Hub, Front Cover, ... oil pump screen must be replaced with original parts or purchased new as follows: ... pump with part number 12555283. This engine is built to production point of build ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 121 August 2004 ... 7P) 1992-94 Chevrolet Y (LT1)(5.7P) Engine-Specific Content: Crankshaft Hub, Front Cover, ... oil pump screen must be replaced with original parts or purchased new as follows: ... pump with part number 12555283. This engine is built with 1994 production parts. ... valve train, use 1994 components. This engine is built to production point of build ... 5.7P) 1996 Chevrolet Y (LT1)(5.7P) Engine-Specific Content: Front Cover, Oil Pan, Oil Pump ... oil pump screen must be replaced with original parts or purchased new as follows: ... pump with part number 12555283. This engine is built to production point of build ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 122 August 2004 ... New 5.7L 2001 Chevrolet Y (LS6) Engine-Specific Content: Harmonic Balancer, Oil Pan, ... New 5.7L 2003-04 Chevrolet Y (LS6) Engine-Specific Content: Harmonic Balancer, Oil Pan, ... New 5.7L 2004 Pontiac 8V (LS1) GH4 Engine-Specific Content: Harmonic Balancer, Oil Pan, ... 2001-02 Chevrolet, Pontiac F (LS1) Engine-Specific Content: Harmonic Balancer, Oil Pan, ... arm covers to be transferred form original engine. INSTALLATION INSTRUCTIONS No ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 124 August 2004 ... INSTRUCTIONS This Chevrolet Mark IV engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Parts ... , and valve covers to the replacement engine. Thoroughly clean all old parts to avoid ... install the sensor on the replacement engine. Use a thread sealer to prevent coolant ... in place of the pump supplied with this engine. Attach two Goodwrench engine decals ( ... covers. CAUTION: The oil pump in this engine must be primed before starting the ... engine. Refer to vehicle service chassis manual ... proper priming procedures. Also, check engine oil level before starting engine. Use 6 ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 129 August 2004 ... INSTRUCTIONS This Chevrolet Mark IV engine has been remanufactured subsequent to ... design refinements not included in original service information (i.e., 1982 engines ... If future service is required for this engine, consult GM Parts catalogs, GM Part and ... and valve covers to the replacement engine. Thoroughly clean all old parts to avoid ... install the sensor on the replacement engine. Use a thread sealer to prevent coolant ... in place of the pump supplied with this engine. Attach two Goodwrench engine decals ( ... covers. CAUTION: The oil pump in this engine must be primed before starting engine. ... proper priming procedures. Also, check engine oil level before starting engine. Use 6 ... conditions. DAMAGE COULD RESULT IF ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP ... | |
| GOODWRENCH SERVICE REPLACEMENT ENGINES Section V Page 131 August 2004 ... 1976 through 1990 C, K G P 123 trucks originally manufactured with 454 engines with the ... following restrictions: Remanufactured engine may be 2 or 4 bolt design. Not ... in place of the pump supplied with the engine. 1990 production engines use ESC knock ... sensor. Remanufactured engines must be modified for use on 1990 ... | |
