38 results for water pump installation found in 0.000 seconds

GENERAL INSTALLATION PROCEDURES Section III Page 9 August ... , it may not seal properly, allowing water and other contaminants to enter the ... , replace the cover. Mechanical Fuel Pump Clean the fuel pump and inspect the ... . Remember that mechanisms inside the pump wear. If the fuel pump has many miles ...

GENERAL INSTALLATION PROCEDURES Section III Page 10 August ... occur, replace the clutch disc. Water Pump It is recommended to replace the water ... pump when installing a new engine. However, ... if the old pump is reused, check for cavitation ... and smooth bearing feel. Replace the pump if it shows signs of wear. Spark Plug ... , cracks and burrs. The distributor/oil pump drive should be free of nicks, burrs, ... conditioning compressor Power steering pump Sensors All pulleys and other bracketry ...

GENERAL INSTALLATION PROCEDURES Section III Page 11 August ... prior to installing the new engine. Oil Pump, Pick-up Tube and Screen These ... and to clean silicates from the water pump shaft to prevent shaft seal damage. ...

GENERAL INSTALLATION PROCEDURES Section III Page 12 August ... 2004 INSTALLATION PROCEDURES Flush the Cooling System A ... aluminum and remove silicates from the water pump shaft that form from the coolant ... . Installation The following is an outline of the ... facing downwards. Throughout the entire installation process, be sure to torque all bolts ... 's specifications. 1. Install the oil pump and the oil pump shaft. Fill the pump ... the initial suction and priming of the pump. Do not use white lithium grease to pack ... the oil pump. This grease won't breakdown and will ... to keep the gaskets in place during installation. Lubricate the front cover crankshaft ... to seal the bolts that are entering the water jackets with RTV sealant. Put the RTV ... 5. Install the damper using the damper installation tool. Be sure to visually inspect the ...

GENERAL INSTALLATION PROCEDURES Section III Page 13 August ... 2004 INSTALLATION PROCEDURES cont. 8. Rotate the engine ... can be pre-lubed by priming the oil pump with a hand-held drill. Using an oil ... pump priming tool or distributor shaft, ... rotate the oil pump with a drill at 200 to 500 RPM for two ... does not seal properly to the heads, water and other contaminants can enter the ... manifold(s). 16. Install the fuel pump and fuel lines being sure of proper ... : Front end bracketry Crankshaft pulley Water pump pulley Air conditioning compressor ... Air pump Alternator (generator) Power steering ... pump All sensors that were removed from the ...

excessive oil consumption, coolant hose/water pump failure, melted wiring or ... malfunctions caused by improper installation of non-factory accessory items. 4. ...

on coolant to flow through the engine water jackets and absorb the heat of ... core, or sludge build-up in the engine water jackets or coolant passages. The ... radiator drain cock, a failed water pump and internal engine cracks and gasket ... 99-06-02-012B. Only use distilled water to mix with new coolant. Never add tap ... water ...

Check Valve, Oil Pan, Spark Plugs, and Water Pump INSTALLATION INSTRUCTIONS This ... reach the full mark. CAUTION: The oil pump in this engine must be primed before ... IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12360620 138 CID Reman ... Check Valve, Oil Pan, Spark Plugs, and Water Pump INSTALLATION INSTRUCTIONS This ... reach the full mark. CAUTION: The oil pump in this engine must be primed before ... IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ...

, Front Cover, Oil Check Valve, P/S Pump Pulley, Spark Plugs, and Water Pump ... INSTALLATION INSTRUCTIONS This engine has been ... reach the full mark. CAUTION: The oil pump in this engine must be primed before ... IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12360624 138 CID Reman ... Cover, Oil Check Valve, Oil Pan, Oil Pump w/Screen, P/S Pump Pulley, Spark Plugs ... , Timing Chain Tensioner and Guides, Water Pump INSTALLATION INSTRUCTIONS This ... reach the full mark. CAUTION: The oil pump in this engine must be primed before ... IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ...

Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, Spark Plugs, and Water Pump ... INSTALLATION INSTRUCTIONS This engine has been ... reach the full mark. CAUTION: The oil pump in this engine must be primed before ... IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12360626 138 CID Reman ... Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, Spark Plugs, and Water Pump ... INSTALLATION INSTRUCTIONS This engine has been ... reach the full mark. CAUTION: The oil pump in this engine must be primed before ... IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ...

Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, Spark Plugs, and Water Pump ... INSTALLATION INSTRUCTIONS This engine has been ... reach the full mark. CAUTION: The oil pump in this engine must be primed before ... IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12361504 138 CID Reman ... Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, Spark Plugs, and Water Pump ... INSTALLATION INSTRUCTIONS This engine has been ... reach the full mark. CAUTION: The oil pump in this engine must be primed before ... IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ...

Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, Spark Plugs, and Water Pump ... Knock, Map, Cool Temp or Oil Lvl Sen. INSTALLATION INSTRUCTIONS Please Notes that ... 22579611 is included in service engine installation kit, catalog group 0.010). Pontiac ... engine requires transferring the water pump cover from the original engine. ... This is necessary to ensure that the water pump cover contains the nipple required ... for the heater hose. The water pump cover gaskets should be replaced at ... are included in the service engine installation kit. See catalog group 0.010.) ... Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, Spark Plugs, and Water Pump ... Knock, Map, Cool Temp or Oil Lvl Sen. INSTALLATION INSTRUCTIONS No special installation ...

Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, Spark Plugs, and Water Pump ... Knock, Map, Cool Temp or Oil Lvl Sen. INSTALLATION INSTRUCTIONS Please Notes that ...

Cover, Oil Check Valve, Oil Pan, P/S Pump Pulley, Spark Plugs, and Water Pump ... : 24573914 Replaced By: 12465099 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Front Cover, Oil Check Valve, Oil Pan, Water Pump, and Spark Plugs Notes: Does not ... : 12363189 Replaced By: 12465153 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Pan, Timing Chain Housing, Spark Plugs, Water Pump, and P/S Pump Pulley Notes: Does ... , 88894199, 88890518 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book ...

, Spark Plugs, Engine Oil Additive, Water Pump/Pulley Assembly, Water Outlet, ... . Replaces: 12458066 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... : Balancer, Flywheel, Oil Pan, Oil Pump, and Oil Filter Notes: For engines with ... . Replaces: 12564895 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book ...

Sensor, Spark Plugs, Themostat and Water Pump Notes: Does not include Intake ... Exhaust Manifold and attaching parts. INSTALLATION INSTRUCTIONS Do not remove the engine ... clean valve covers. CAUTION: The oil pump in this engine must be primed before ... ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12360686 231 CID ... -Specific Content: Front Cover and Oil Pump INSTALLATION INSTRUCTIONS Do not ... part number 25537239. CAUTION: The oil pump in this engine must be primed before ... ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12360687 231 CID ... Engine-Specific Content: Front Cover INSTALLATION INSTRUCTIONS Do not remove the engine ... clean valve covers. CAUTION: The oil pump in this engine must be primed before ... ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ...

, Lower Intake Manifold, Front Cover, Water Pump, Balancer, and Crank Cam Posn. ... : 12564295 Replaced By: 89017668 INSTALLATION INSTRUCTIONS Do not remove the engine ... clean valve covers. CAUTION: The oil pump in this engine must be primed before ... ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 12482057 231 CID New ... : 12568293 Replaced By: 89017665 INSTALLATION INSTRUCTIONS Do not remove the engine ... clean valve covers. CAUTION: The oil pump in this engine must be primed before ... ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ...

L32) Replaces: Replaced By: 89017666 INSTALLATION INSTRUCTIONS Do not remove the engine ... clean valve covers. CAUTION: The oil pump in this engine must be primed before ... ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED. 89017667 231 CID New ... Covers, Oil Level Sensor, Oil Pan, and Water Pump Notes: Does not contain Exhaust ... , 12371978, 24508875 Replaced By: INSTALLATION INSTRUCTIONS Do not remove the engine ... clean valve covers. CAUTION: The oil pump in this engine must be primed before ... ENGINE IS STARTED WITHOUT OIL OR IF OIL PUMP IS NOT PRIMED ...

-Specific Content: Oil Filter, Oil Pan, Water Pump, Spark Plugs, and Flywheel Notes ... , 88894203 Replaced By: 89017685 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book ...

Level Sensors, Oil Press Sensor, Oil Pump w/Screen, and Water Pump w/Pulley ... . Replaces: 12369567 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Level Sensors, Oil Press Sensor, Oil Pump w/Screen, Water Pump w/Pulley, and ... . Replaces: 12458125 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... L47) Replaces: 12577028 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book ...

KL5) Engine-Specific Content: Oil Pan, Water Pump, Oil Pump, and Timing Chain Notes ... ). Replaces: 12513025 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Gas Engine-Specific Content: Oil Pan, Water Pump, Oil Pump, and Timing Chain Notes ... KL5. Replaces: 12533598 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book ...

, Oil Filter w/Adapter, Oil Pan, Oil Pump, PCV Valve, Spark Plugs, Thermostat ... Housing, and Water Pump w/Pulley Notes: Replaces: Replaced ... By: 12567315 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... , Oil Level Sensor, Oil Pan, Oil Pump Suction Pipe, PCV Valve, Spark Plugs, ... Temperature Sensor, Thermostat Housing, Water Pump w/Housing, and Water Pump w/ ... : 12369570, 12529514 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Cap, Oil Filter w/Adapter, Oil Pan, Oil Pump, and PCV Valve Notes: On 1995-97 models ... : 12369571, 12529515 Replaced By: INSTALLATION INSTRUCTIONS No special installation ...

, Oil Filter w/Adapter, Oil Pan, Oil Pump, PCV Valve, Spark Plugs, Thermostat ... Housing, Water Pump w/Pulley, and Engine Oil Replaces: ... 12369569, 12529512 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... New 4.6L 2001-02 Cadillac K (L37) INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... for Eldorodo, swap dipstick tubes. INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... LD8) Replaces: 12458126 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ...

Replaces: Replaced By: 88890536 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Replaces: Replaced By: 88890536 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Balancer, Oil Pan, Front Cover, Water Pump and Rocker Covers INSTALLATION ... INSTRUCTIONS No special installation instructions are necessary. Please ... refer to the general installation procedure section of this book. ... Balancer, Oil Pan, Front Cover, Water Pump and Rocker Covers INSTALLATION ... INSTRUCTIONS No special installation instructions are necessary. Please ... refer to the general installation procedure section of this book. ...

MY Starter/Trans/Eng mounting bolts. INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... -Specific Content: Crankshaft, Inj Pump Drive, Oil Pump w/Screen, Conn. Rod and ... Chain Notes: Engine does not include Water Pump, Intake or Exhaust Manifold, ... Pan. Replaces: 22536528 Replaced By: INSTALLATION INSTRUCTIONS Oil Pump Screen Height: ... The oil pump pickup screen has a possibility of ... , check the location of the screen. Oil Pump: On all "E" or "K" models, remove the ... oil pump from the old engine. If the engine ... it is suggested you purchase a new oil pump. If it is low mileage and the oil pump ... worked well, transfer the pump from the old engine. Failure to change ...

Replaces: Replaced By: 88890540 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Replaces: 12565185 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Balancer, Oil Pan, Front Cover, Water Pump, and Rocker Covers Replaces: 88984275, ... , 88894258 Replaced By: 89017657 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... LM4) M30 Engine-Specific Content: Oil Pump, Front Cover, Water Pump, and Rocker ... : 88984276, 12577732 Replaced By: INSTALLATION INSTRUCTIONS No special installation ...

. Replaces: 14009800 Replaced By: INSTALLATION INSTRUCTIONS Part number 10067353 ... Pan, Intake Manifold, Fuel Rail, and Water Pump Replaces: Replaced By: 88894382 ... INSTALLATION INSTRUCTIONS No special installation instructions are necessary. Please ... refer to the general installation procedure section of this book ...

Pan, Intake Manifold, Fuel Rail, and Water Pump Replaces: Replaced By: 88890543 ... INSTALLATION INSTRUCTIONS No special installation instructions are necessary. Please ... refer to the general installation procedure section of this book. ... Hub, Oil Pan, and Valve Rocker Cover INSTALLATION INSTRUCTIONS Part number 12513151 5.7 ...

Content: Front Cover, Oil Pan, Oil Pump w/Shaft and Cover, Water Pump w/Shaft ... , Exhaust Manifold, Starter, Flywheel, Water Pump, Ignition or Attaching Parts ... Replaces: Replaced By: 88894198 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Replaces: 12520268 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Replaces: 10048971 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... block has English mounting threads. INSTALLATION INSTRUCTIONS No special installation ...

W4 Engine-Specific Content: Oil Pan INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Pan, Intake Manifold, Fuel Rail, and Water Pump Replaces: Replaced By: 88890544 ... INSTALLATION INSTRUCTIONS No special installation instructions are necessary. Please ... refer to the general installation procedure section of this book. ... Pan, Intake Manifold, Fuel Rail, and Water Pump Replaces: 12457659 Replaced By: ... 88890545 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Pan, Intake Manifold, Fuel Rail, and Water Pump Replaces: 12455110 Replaced By: ... 88894386 INSTALLATION INSTRUCTIONS No special installation ...

Content: Front Cover, Oil Pan, Oil Pump w/Shaft and Cover, Water Pump w/Shaft ... Replaces: 12533599 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Replaces: 12524896 Replaced By: INSTALLATION INSTRUCTIONS On "Y" car applications, ... valve covers, oil pan, and oil pump screen must be replaced with original ... (w/gasket) Valve Cover Bolts Oil Pump Screen Oil Pan Kit/Pan Gasket ... 'press' after installing the oil pump screen,replace oil pump with part ...

Replaces: 12523000 Replaced By: INSTALLATION INSTRUCTIONS On "Y" car applications, ... valve covers, oil pan, and oil pump screen must be replaced with original ... Valve Covers Valve Cover Bolts Oil Pump Screen Oil Pan Kit/Pan Gasket 1992 N ... 'press' after installing the oil pump screen,replace oil pump with part ... Content: Front Cover, Oil Pan, Oil Pump w/Shaft and Cover, Water Pump w/Shaft ... , Exhaust Manifold, Starter, Flywheel, Water Pump, Ignition or Attaching Parts ... Replaces: 12533597 Replaced By: INSTALLATION INSTRUCTIONS On "Y" car applications, ... valve covers, oil pan, and oil pump screen must be replaced with original ... (w/gasket) Valve Cover Bolts Oil Pump Screen Oil Pan Kit/Pan Gasket ... 'press' after installing the oil pump screen,replace oil pump with part ...

Balancer, Oil Pan, Front Cover, Water Pump, and Rocker Covers Replaces: 88894057 ... Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... : Harmonic Balancer, Oil Pan, Oil Pump, Front Cover, Water Pump, and Rocker ... : 88984272, 88894254 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... : Harmonic Balancer, Oil Pan, Oil Pump, Front Cover, Water Pump, and Rocker ... Covers INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... : Harmonic Balancer, Oil Pan, Oil Pump, Front Cover, Water Pump, and Rocker ...

: Harmonic Balancer, Oil Pan, Oil Pump, Front Cover, Water Pump, and Rocker ... Replaces: 89017350 Replaced By: INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book ...

12465229 366 CID New Electric Fuel Pump Application Only 6.0L 1986-89 ... Rocker Covers Notes: Electric Fuel Pump Application Only. When replacing ... dampener, must also use 1-12529747 water pump. Replaces: 12530366 Replaced By ... : INSTALLATION INSTRUCTIONS NOTICE: When using this ...

88890535 366 CID New Mechanical Fuel Pump Application Only 6.0L 1986-89 ... Rocker Covers Notes: Mechanical Fuel Pump Application Only. When replacing ... dampener, must also use 1- 12529747 water pump. Replaces: 12530366 Replaced By ... : INSTALLATION INSTRUCTIONS NOTICE: When using this ...

Balancer, Oil Pan, Front Cover, and Water Pump Replaces: 88984277, 88894062, ... 88894259 Replaced By: 89017659 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... , Replaced By: 89017660 88894063 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... : 88984282 Replaced By: 89017357 INSTALLATION INSTRUCTIONS No special installation ... necessary. Please refer to the general installation procedure section of this book. ... Balancer, Oil Pan, Front Cover, and Water Pump Replaces: 12573037, 88894261, ... 88984279 Replaced By: 89017661 INSTALLATION INSTRUCTIONS No special installation ...

: 12524683, 10181240 Replaced By: INSTALLATION INSTRUCTIONS Part number 12532427, ... 1994 trucks, you must purchase a new water pump and lower radiator hose. For 1990 ... and prior, you must replace the water pump with part number 12529747 to clear the ... 8" damper. Year Water Pump Hoses Usage 1991-94 12529192 ...