Page 30 of 2009 Performance Parts by GM Parts Direct

crate engines small-block complete your small-block crate engine select the parts below to finish off your crate engine and get running in less time 10185063 intake manifold 12342089 small-block chrome timing cover 12480127 short aluminum valve covers also available 350 hot cam kit bolt motor mount 2 req carburetor holley 770-cfm fan 19.5 serpentine belt fan 19.5 v-belt 12480002 460308 19170093 15563127 15644302 9440224 19150657 88961767 12338130 12338107 382919 6415325 12551537 24241872 22188497 15731260 12341993 3952301 12370838 12370839 12497698 crate engines small-block our low-profile dual-plenum aluminum intake manifold helps make great power and fits under the hood of almost every vehicle accommodates both holley 4160-series and quadrajet carburetors this attractive chrome cover fits 1969-1991 small-block v-8 and 90-degree v-6 engines it is a direct replacement for covers that use a bolt-on timing pointer and it includes the oil seal this racing-inspired design has the bowtie logo and chevrolet lettering the cast aluminum covers include pcv holes grommets included and oil baffles 12496822 intake manifold vortec eliminator this aluminum single-plane intake manifold is designed for use with vortec cylinder heads p/n 12558060 25534421 25334446 fast burn heads p/n 12464298 or vortec bowtie heads p/n 25534421 and 25534426 to build maximum power and torque requires manifold bolts p/n 12550027 12341998 fuel pump block-off plate this attractive chrome plate is embossed with the chevrolet bowtie logo it is used in place of a mechanical fuel pump on the engine block includes a nonasbestos gasket 12341670 chrome short valve covers fan bolts 4 req fan clutch serpentine belt fan clutch v-belt fan stud nuts 4 req fan studs 4 req serpentine belt fan studs 4 req v-belt add sparkle to your small-block with these classic chrome valve covers designed for pre-1986 cylinder heads with perimeter-style hold-down bolts the covers feature the bowtie logo and chevrolet name 12366573 intake manifold vortec design designed for small-block engines up to 400-cu-in and equipped with vortec-type cylinder heads this high-rise aluminum intake manifold has a dual-plane design that helps the engine deliver a strong balance of horsepower and torque 12355612 fuel pump street performance use this mechanical fuel pump on carbureted engines it has 7-psi shutoff pressure and a free-flow rate of 110 gph the lower housing can be rotated to reposition the inlet and outlet ports to suit different applications 12497979 aluminum black crinkle valve covers center bolt design fuel pump high capacity small-block harmonic balancer magnetic drain plug motor mount 2 req car motor mount 2 req truck oil filler cap push-in oil filter adapter roller rocker arm kit 1.5:1 ratio aluminum roller rocker arm set 1.6:1 ratio aluminum serpentine accessory drive belt system deluxe valve covers with red chevrolet bowtie logo they include pcv holes grommets included and are approximately ¼ taller than production kit includes bolts washers and seals note use valve cover gasket p/n 10046089 88894341 water pump long-style the later-style cast-iron water pump has the long leg design reinforced snout and a 3/4-inch snout reduced to 5/8-inch at end of shaft use it with the 350 ho 383 and zz4 engines 88965829 cnc d carburetor spacer dualplane 1-inch fully machined from billet aluminum this lightweight 1-inch spacer carries the gm performance parts logo on the front and rear it fits quadrajet-type and holley carburetors 12497985 chrome-finish aluminum valve covers center bolt design valve covers feature the chevrolet bowtie logo and include pcv holes grommets included approximately ¼-inch taller than production kit includes bolts washers and seals note use valve cover gasket p/n 10046089 serpentine accessory drive belt system without a/c 12497697 spark plug wires red gm performance 135° boot spark plug wires red gm performance 90° boot standard starter offset bolt holes standard starter straight bolt holes transmission mount 4l60 4l80 transmission mount 700r4 12361056 12361057 10496873 10496871 15767858 2218814 22188145 17990778 12497978 24502540 12363970 12495826 14011012 12496806 93440806 hei distributor this high-energy electronic distributor is a must for steel roller cams it offers ignition advance curve for high-performance applications 12368084 engine oil primer tool use to prelube the engine bearings and prime the oiling system prior to starting a new crate engine requires electric drill or similar not included 12342071 air cleaner classic design a classic in chrome this 14 round air cleaner has the chevrolet name and a bowtie wing nut it fits most two and four-barrel carburetors 88961867 distributor aluminum billet hei distributor features a cnc-machined aluminum housing ball bearing guide oversized shaft and long-sintered bushing for durability it also has mechanical and vacuum advance brass terminal cap connector p/n 12167658 attaches tach and 12-volt power supply wire 12361146 high-torque mini-starter designed to deliver powerful starting capability in a compact size this highperformance gear-reduction starter fits 153 or 168-tooth flywheels 12342080 air cleaner chevrolet-logo high-performance design transmission mount 700r4 transmission mount th400 valve covers polished aluminum valve cover adapter centerbolt to flange mount valve covers polished aluminum die-cast 14 round high-performance-style air cleaner chrome lid with embossed chevrolet name fits most four-barrel and two-barrel carburetors 12342024 chrome water neck add a bit of chrome to your engine with this detailed water neck it includes a neoprene o-ring and chrome fasteners it fits 1966-1975 chevrolet camaro and chevelle models with v-8 engines 10465143 lightweight starter remanufactured 19170092 carburetor holley 670-cfm water pump long-style aluminum water pump short-style aluminum wire loom kit small-block originally designed for 1993-97 camaros and firebirds equipped with the lt1 engine this lightweight high-performance starter can be used on any small-block or big-block engine with a 12.75-inch 153-tooth flywheel holley s 4160-style 670-cfm four-barrel carburetor is perfect for many crate engines it has show-quality polished details center-hung fuel bowls vacuum secondaries and power valve blowout protection available for purchase online at gmperformanceparts.com 56 buy online at www.gmperformanceparts.com buy online at www.gmperformanceparts.com 57

[close]