Catalog: GM Performance Parts 2006 Catalog
Company/Brand: GM Parts Direct
small block chevy cam lifters in GM Performance Parts 2006 Catalog by GM Parts Direct
: GM PERFORMANCE PARTS BOWTIE SPORTSMAN BLOCK This is the block to buy if you want to ... GM Performance Parts Bowtie Sportsman block has been the starting point for ... countless racing engines. These iron blocks are available in a variety of finish ... any engine combination. Most of these blocks have siamesed cylinder walls 1 and four ... that are secured by Grade 8 bolts. All blocks in this family have a 9.025 deck ... height. The Bowtie Sportsman blocks are a great foundation for your serious ... between 350 and 500 horsepower. Bowtie blocks are called out by main journal sizes (i ... to remember 283s). Bowtie Sportsman Block Technical Notes: 2.00" O.D. cam ... at all five locations (except for block 10051183) 0.900" thick main bearing ... head gasket sealing Tall lifter bore blocks may require clearancing the top of ...
One-Piece Rear Main Seal Race Block (front) GM PERFORMANCE PARTS RACE ... BLOCKS Our race blocks take the guess work out of what block ... offer you such a huge selection of race blocks that have been precision, CNC-machined ... with tighter tolerances than our Bowtie blocks before you even get them. These blocks ... to your GM Performance Parts race block! See chart on page 132 for complete ... . GM Performance Parts Race Block Technical Notes: These blocks are CNCd ... pins are blueprinted! Non-standard cam bearings required (see each block for ... details) Cam bosses are enlarged to allow machining ... bore check data sheet provided These blocks may require clearancing the top of ... for some aftermarket mechanical roller lifters Timing system clearance should be ...
Short Deck Race Block (rear) Short Deck Race Block (front) ... 137 24502503 350 Cast Iron Bowtie Race Block Cast iron competition block right out ... caps on center 3 mains 2.00" O.D. cam bearings (1.867" I.D.) P/N 12370843 ... , 350 Bore size Short-Deck Bowtie Race Block CNC Cast iron competition block ... .325" deck (as of 10/03) (standard deck blocks are 9.025"), can be machined to 8.200" ... deck height Camshaft is raised 0.433" to 4.955" Cam ... Integral oil restrictors Must use Big Block water pump, must raise water pump with ... Can be machined to accept any small-block Chevy cylinder head Machined as 4. ... , 350 Bore size Medium-Deck Bowtie Race Block CNC Cast iron competition block ... 3 mains 8.700" deck (standard deck blocks are 9.025"), can be machined to 8.500" ...
Race Blocks Continued 12480045 283 Main Size NASCAR ... Busch Series Block CNC-machined, cast iron NASCAR ... competition block 9.025" deck height 4-bolt NASCAR- ... block specific steel mains, 17 splayed caps ... (siamese bores) Machined for 2.280" cam bearings .875" lifter bores -06AN ... 1/2" NPT water hole on each side of block Dry sump only (no oil filter boss) ... 350 Main Size NASCAR Busch Series Block CNC-machined, cast iron NASCAR ... competition block 9.025" deck height 4-bolt NASCAR- ... block specific steel mains, 17 splayed caps ... (siamese bores) Machined for 2.280" cam bearings .875" lifter bores -06AN ... 1/2" NPT water hole on each side of block Dry sump only (no oil filter boss) ... 283 Main Size NASCAR SB2.2 Series Block CNC-machined, cast iron NASCAR ...
detail C Valve Lifter Guide, "Quick Cam" B Hydraulic Roller Lifter Kit C 164 ... lifter detail C NOTE: NOTE: VALVE LIFTERS A. 14044875 Lifter Bore Repair Kit Dont ... scrap an expensive engine block because of a damaged lifter bore! ... bottom of the sleeve is flush with the camshaft cavity. Drill a 7/16" hole through the ... 2" oil hole before installing it in the block. B. 88958652 Valve Lifter Guide, "Quick ... Cam" This composite lifter guide is the same ... as used on LS Series GM small-blocks, but with mounting holes for use on Gen ... I GM small-blocks. For use with hydraulic roller lifters ... guide makes it possible to remove the camshaft without removing the intake and lifters ... friction in the guide to hold the lifters in place if the rocker arms are backed ... off and the camshaft is rotated two full revolutions to push ...
350 Hot Cam Kit A Camshaft Retainer B Camshaft Rear Cover Kit C 166 Cam Button Spacer ... D NOTE: CAMSHAFTS A great camshaft delivers power and easy drivability and ... you get with GMPPs factory-engineered cams. Extensive research and development, ... standards, are behind every one of our camshafts. Our extensive array of cams includes ... steel gear MUST be used with steel camshafts or engine damage can occur. A. ... 12480002 350 Hot Cam Kit Off-highway kit for converting ... for showroom stock racing or to improve small-block originally equipped with roller tappet ... camshaft. Significant horsepower gains are ... caps, special valve springs, and "Hot" camshaft. Kit includes camshaft, 16 roller rocker ... the following items: 24502586 One Camshaft 12370839 16 Roller Rocker Arms Kit ...
Chain Kit A LT4 Front Cover Plug C Camshaft Bolt B 172 NOTE: TIMING CHAIN SPROCKETS ... timing between the crankshaft and camshaft. GM Performance Parts timing chains and ... crank sprocket P/N 3735413, and iron cam sprocket P/N 3735412. Cannot be used ... and-newer engines with hydraulic roller camshaft. 12371043 Single Roller Timing Chain Kit ... -andnewer engines with roller lifter camshaft, except LT1 and LT4. Kit includes chain ... 14088783, crank sprocket P/N 14088784, cam sprocket P/N 12552129, retainers and ... bolts. Will not work with flat tappet camshafts or LT1 and LT4 engines. 12370835 ... , crankshaft sprocket P/N 14088784, camshaft sprocket P/N 10214880, and water pump ... gear P/N 12551728. Use with pin drive camshaft only. To convert 1993 and 1994 engines ... , use camshaft P/N 12551705, distributor P/N 1104032, ...
