Alighnment Stage Module Type SA...M by IKO Nippon Thompson

More catalogs by IKO Nippon Thompson | Alighnment Stage Module Type SA...M | 10 pages | 2011-08-31

Ads

Page 5 of Alighnment Stage Module Type SA...M

characteristics table 1.1 accuracy of the sa m series max range of movement type and size sa250m sa420m sa800m note 1 2 sensor specifications table 5.1 repeatability 2 specifications of sensor proximately sensor 12 to 24 vdc 10 ma or less open corrector max switching current applied voltage residual voltage 10 table 5.2 specifications of connector connectors tyco electronics amp k.k sensor side opposite side sensor type 2 xy motion mm 15 15 45 1 angle compensation motion degree 10 5 8 xy motion mm 0.002 1 angle compensation motion sec 6 3 1.5 power voltage power supply voltage pin no signal name 1 indicates a value when the stage is located at the reference position indicates a value when the stage is located at the reference position and the rotation center at the stage center current consumption unit mm table 1.2 accuracy of the am series stroke length 30 30 90 120 100 ma 30 vdc or less less than 1.0 v at 100 ma of switching current less than 0.4 v at 16 ma 2 3 4 5 cap housing pre-origin cw limit ccw limit power input gnd prepare applicable connector plug housing 172168-1 172160-1 connector 170365-1 connector 170363-1 type and size am25 am40 am60 am86 note 1 track rail length 130 180 290 390 repeatability positioning accuracy parallelism in operation b backlash output operation operation indicator when approaching off led orange turned off at detection vcc 6 remark 0.002 0.020 0.008 0.003 circuit diagram not applicable for the specification without a ball screw main circuit out gnd table 1.3 height dimension of the am series module height dimension 47 78 110 148 0.010 unit mm type and size am25 am40 am60 am86 tolerance of the height dimension table 6 sensor timing chart remark indicates a value from the mounting surface to the center of the module upper surface when the upper and lower axes bisect at right angle and the linear motion rolling guides of each shaft is located at the middle of its stroke table 2 maximum speed lead mm 4 5 4 3000 5 250 type and size sa250m sa420m sa800m am25 am40 am60 am86 motor revolution r/min 3000 max speed mm/sec 200 250 200 origin c-phase of the encoder pre-origin sensor ccw limit sensor cw limit sensor mechanical stopper off b on c a off off d stroke length f e unit mm table 3 allowable load allowable load n 98 470 680 100 500 790 3040 1 1 table 4 table inertia and starting torque table inertia j t 10 5kg m2 0.102 0.48 3.50 0.028 0.08 0.59 4.97 size starting torque t0 n m 0.02 0.07 0.12 0.02 0.07 0.12 0.17 note 1 1 1 a 1 b 4 4 5 4 4 5 5 c 2 2 3 2 2 3 3 d 15 15 45 15 15 45 60 e 8 8 16 8 8 16 8 f 46 48 117 46 48 117 136 type and size sa250m sa420m sa800m am25 am40 am60 am86 note 1 sa250m sa420m sa800m am25 am40 am60 am86 type and size sa250m sa420m sa800m am25 am40 am60 am86 note 1 1 1 1 90 90 133 155 2 1 2 2 2 the origin point coincides with the stroke center 2 indicates a load applicable to the stage at the arbitrary location indicates a load applicable to a unit of the module calculate a load to a unit of the module by using the loading location when constructing a stage indicates a value for reference 7 1n 0.102kgf 0.2248lbs 1mm 0.03937inch 8