Page 193 of Tool Catalog 151 by Klein Tools

chicagoŽ grips chicagoŽ grips ­ for large diameter conductors ˇ designed for hollow conductors and other large-diameter cables jaws are shaped to ˇ roundvirtually eliminatingprovide maximum contact with the cable conductor damage these grips are special order only please allow 30 days for ˇ delivery these are not returnable 1628-50 furnished with floating jaw held ˇ cat no by a boltisswaged into the removableof the grip secured in place lever arm 1628-40 ˇ ˇ by a nut and cotter pin jaw must be removed to insert cable orders must specify exact outside diameter of cables circular mills with strand combination or manufacturer s code each grip is made for one-size cable only wire pulling grips 1628-50 cat no 1628-16p 1628-30 1628-40 1628-50 minimum cable 2 acsr .31 7.87 mm 477,000 cm acsr .85 21.59 mm 1,033,500 cm acsr 1.24 31.50 mm 666,600 cm acsr 1.00 25.40 mm maximum cable 477,000 cm acsr .88 22.35 mm 1,033,500 cm acsr 1.24 31.50 mm 1,590,000 cm acsr 1.54 39.12 mm 2,500,000 cm alu 1.82 46.23 mm maximum safe load 15,000 lbs 6818 kg 20,000 lbs 9090 kg 25,000 lbs 11,364 kg 25,000 lbs 11,364 kg jaw length 7-1/4 184 mm 10-3/4 273 mm 10-3/4 273 mm 10-3/4 273 mm approx weight each 17 lbs 7.73 kg 27 lbs 12.27 kg 34 lbs 15.45 kg 34 lbs 15.45 kg minimum-maximum sizes listed indicate the unfinished size-range capability for each cat no each grip is finished to fit one specific cable size only within range shown maximum safe stringing tension 12,500 lbs to minimize conductor damage chicagoŽ grips ­ for bare acsr aluminum and stranded-copper cables inside jaw of grips ˇ round smoothaluminum contour on this seriescables is ideal for bare acsr and stranded-copper ˇ smooth jaws grip with maximum contact and are less likely to damage conductors cat no 1656-20 1656-30 1656-40 1656-50 1656-60 minimum cable 6 acsr .20 5.08 mm 2 acsr .31 7.87 mm .53 13.46 mm 397,500 cm acsr .74 18.80 mm 477,000 cm acsr .86 21.84 mm maximum cable 1/0 acsr .40 10.16 mm .53 13.46 mm 336,400 cm acsr .74 18.80 mm 477,000 cm acsr .86 21.84 mm 605,000 cm acsr .96 24.38 mm maximum safe load 4500 lbs 2045 kg 4500 lbs 2045 kg 8000 lbs 3636 kg 8000 lbs 3636 kg 8000 lbs 3636 kg jaw length 4 102 mm 4-3/4 121 mm 5-1/2 140 mm 5-1/2 140 mm 5-1/2 140 mm 1656-30 approx weight each 3 lbs 1.36 kg 3.75 lbs 1.70 kg 8.30 lbs 3.76 kg 8.30 lbs 3.76 kg 8.20 lbs 3.71 kg chicagoŽ grips ­ for aluminum conductors ˇ lightweight grips designed for use on aluminum conductors in distribution work provide maximum contact with circumference of cable ˇ round jaws shaped toconductors less likely to damage spring locking loop handles allowing ˇ supplied withpositionand easier placement on cable jaws to be held in open for ˇ can be supplied with hot-line latch on special order cat no 1678-20 1678-30 1678-40 1678-50 minimum cable .96 24.38 mm 1.02 25.91 mm 1.08 27.43 mm 1.14 28.96 mm maximum cable 1.02 25.91 mm 1.08 27.43 mm 1.14 28.96 mm 1.20 30.48 mm maximum safe load 8000 lbs 3636 kg 5500 lbs 2500 kg 5500 lbs 2500 kg 5500 lbs 2500 kg jaw length 5-11/16 144 mm 5-11/16 144 mm 5-11/16 144 mm 5-11/16 144 mm 1678-30 approx weight each 8.30 lbs 3.76 kg 8.20 lbs 3.71 kg 8.20 lbs 3.71 kg 7.90 lbs 3.58 kg all dimensions are in inches and millimeters unless otherwise specified warning do not exceed rated capacity warning always match proper size and type of grip to application warning before each use clean jaw area and inspect grip for proper operation to avoid slippage 192 permanent anchorage warning grips are to be used for temporary installation not for warning when used on/or near energized lines ground insulate or isolate grip before pulling.

[close]