Page 129 of 1928–1931 Ford MODEL A 2009–2010 Parts & Accessories by MACs Antique Auto Parts

wiring clips clamps grommets wire clips headlamp plugs 28 lights used a 2-hole plug 29-31 used a 3-hole plug when the wires come out of the conduit separate them into the plug this aligns the wires with the socket in the headlight be sure the measurement from the back of the plug to the end of the wire top is .680 reproduction wire ends are too long on some brands this causes the socket spring to bow short out the wiring our main wiring harness has the correct end drill the hole in the plastic deeper to recess the wire end to give the proper distance of .680 or 11/16 the 28 plugs include 4 special brass terminals screws with 2 plugs it buy a k $ave 28-55 frame type 10 clips a14585s 28-55 frame type each a14585 29-31 keeps headlight wiring away from the upturned edge of the engine pan located under the left front hood latch april 29-31 a14590 28-31 holds tail light wire to bottom of wood sub-rails 2 required a14592 1.75 set 0.25 2.75 1.95 2-hole type original style black plastic inserts that fit into the base of a 1 bulb headlight where the wires come together preventing them from shorting out 1 pair does one car 28-48 for tail light loom small a14565 28-e29 for drum tail light holds wire to bottom of wood subrail 2 sets required a14595 2.15 2.30 pair with brass terminal screws a14584ar plug only2 required a14584a 3-hole type 2 required use with 2 bulb headlight black plastic inserts that fit into the base of the headlight where the wires come together preventing them from shorting out 28-32 b14584 e28 e28 8.15 pair 1.30 28-29 holds switch cable mounts on firewall for steel conduit a14577b 28-31 hooks under hood handle holds the main lighting wire harness onto the left frame rail under the hood latch a14598 28-47 on water inlet on firewall a14577a 1.55 1.50 1.95 0.75 wire clip mounting bolt washer sets for wire clip a14577a above firewall rubber grommet sets 6 pieces 1 for the starter rod 2 for the choke end 1 for the ignition cable rod 1 at the terminal box 1 at the firewall for the speedometer cable 28-31 holds clip to water inlet .a14576mb 28-31 original style paint black a14577almb 0.30 0.60 set 28-31 6 pieces a14600as l31 7 pieces same as above plus a grommet for the indented firewall for the gas shut-off valve a14600bs 3.95 set 7.25 set cowl lamp wire supports grommets 3 required the two l shaped wire brackets listed above are used to support the cowl light wire on all cars the vacuum line on open cars 3 of these are used on closed cars one at each inside top corner of the cowl secured by the cowl welting screw the inside top left terminal box screw open cars used 2 brackets for cowl light wires at each inside top corner of the cowl secured by the top rivet of the cowl brace 3 brackets are also required for the vacuum line one at the top left terminal box screw left cowl welt screw on the rear most gas tank clamp for 30-31 cowl light wires a black lacquered loom a14429 covered the wire from cowl light to cowl light the rubber grommet in the bracket was not used mounts on firewall rubber grommets 19-31 large for switch cable also for a14550 .a11580 28-31 large for switch cable support a14550 100 authentic version a14561org 28-32 for ignition wire on instrument panel bracket b14587 28-31 for speedometer cable housing located at the firewall below the choke b14567b 0.90 17.75 1.00 0.70 28-29 30-31 a14593a a14593 2.05 2.00 radiator shell rubber grommet sets for headlight horn holes 28-29 3 pieces a8210as 30-31 3 pieces a8210bs 1.60 set 1.60 set top kick panel retaining clip dome light wire clip 2 required grommet holder for wiper or dome light wires holds the top of the kick panel in place held in place by a bolt that holds the gas tank to the cowl 28-29 with rubber grommet a14593ar 4.30 visit our website macsautoparts.com 716 210-1340 office/technical prices are each unless otherwise noted prices subject to change without notice 127

[close]