Page 72 of Mark Williams Racing Products by Mark Williams Enterprises, Inc.

solid driveshafts mw solid driveshafts are designed to be used in vehicles with solid mounted rear ends or where a single coupler is not long enough these shafts are available in lengths from 6 to 28 long all shafts are machined out of 4340 alloy steel the splines are hobbed micro polished and then heat treated with mw s austemper 40640 process for strength and ductility the splines on 1 3/8 16 40000 40800 40780 spline shafts are o.d ground after heat treat to assure a perfect fit finally all shafts receive a black oxide finish shafts are available with sae 1 3/8 16 13/8 32 spline and 1 1/2 35 splines both ends have 4 full inches of spline and can be shortened up to 2 on 40601 40601 each end couplers and splined shafts should not be used unless perfect alignment is assured mw can also build typical powerglide to 9 ford set-up with 32 spline shaft custom solid driveshafts to your specs up to 34 in length 16 spline driveshafts 41000-06 41000-08 41000-12 41000-14 f/c f/c f/c f/c driveshaft driveshaft driveshaft driveshaft 16 16 16 16 spline spline spline spline 6 long .110.00 8 long .160.00 12 long .190.00 14 long .190.00 41000-16 41000-20 41100-24 41100-28 f/c f/c f/c f/c driveshaft driveshaft driveshaft driveshaft 16 16 16 16 spline spline spline spline 16 long 20 long 24 long 28 long .200.00 .200.00 .200.00 .210.00 32 spline driveshafts 35 spline driveshafts custom driveshafts 41100-spec custom solid driveshaft .275.00 supply length and spline requirements 34 max overall length 41050-06 41050-08 41050-12 41050-16 f/c f/c f/c f/c driveshaft driveshaft driveshaft driveshaft 32 32 32 32 spline spline spline spline 6 long .100.00 8 long .140.00 12 long .140.00 16 long 155.00 41050-20 f/c driveshaft 32 spline 20 long .160.00 41150-24 f/c driveshaft 32 spline 24 long .200.00 41150-28 f/c driveshaft 32 spline 28 long .210.00 41060-06 f/c driveshaft 35 spline 6 long .100.00 41060-24 f/c driveshaft 35 spline 24 long .200.00 41160-28 f/c driveshaft 35 spline 28 long .210.00 41160-32 f/c driveshaft 35 spline 32 long .230.00 quick disconnect powerglide coupler this innovative mw original design allows transmission removal without disturbing the engine or rear end perfect for comp and super comp dragsters powerglide only 40830 40840 40850 40860 40831 40832 40835 40836 mw quick disconnect coupler 177.00 mw quick disconnect coupler long 199.00 mw q/d coupler for dedenbear 177.00 mw q/d coupler .219.00 transmission sleeve short 105.00 male gear half .65.00 transmission sleeve long 140.00 steel lock ring 25.00 when removing the transmission remove the lock ring and slide coupler forward to the back of the transmission this allows the transmission to be moved back and off the dowel pins of the engine slide coupler forward 4 8 requires 4 from trans seal to pinion coupler requires 4 6 from trans seal to pinion coupler requires 4 from trans seal to pinion coupler requires 6 8 from trans seal to pinion coupler with coupler installed and lock ring in place a gap approx 1/8 is left between lock ring and coupler to avoid binding as the chassis works pull trans back up 40837 40839 transmission sleeve dedenbear .105.00 long male gear half .85.00 72

[close]