Page 38 of VNA Calibration Kits, Microwave Components & Adapters Catalog by Maury Microwave

precision vna calibration kits 3.5mm trl/lrl vna calibration kits 8060a tri-kits features trl/lrl calibrations solt short-open-load-thru gated air line dc to 34 ghz description these 3.5mm vector network analyzer vna calibration kits are designed for use with a range of agilent vnas the components in the kits are configured for use in making errorcorrected trl/lrl measurements of devices supplied with 3.5mm connectors from dc to 34 ghz quantity 1 1 1 1 1 1 1 1 1 1 2 1 1 1 description 3.5mm female to male air line 15cm 3.5mm female to male air line 5cm 3.5mm female to male air line 6cm 3.5mm female to male air line 5.3cm 3.5mm female fixed offset short 3.5mm male fixed offset short 3.5mm female open 3.5mm male open 3.5mm female fixed termination 3.5mm male fixed termination 5/16-inch double end wrenches vna software disk operating instructions manual instrument case 8060a components included in 8060a kits model 8043s15 8043s5 8043s6 8043s5.3 8046f 8047f 8048a1 8048b1 8031a5 8031b5 trm/trl/lrl calibration maury trl/lrl calibration kits are tri-kits that contain the components needed to perform three types of calibrations trm/trl/lrl solt and short-open air line load source match can also be measured using the 15cm air line and provided short the following table shows the frequency ranges calibration methods and the standards used to perform a complete 2-port calibration to 34 ghz frequency range dc 160 800 mhz 2.5 ghz 12.5 ghz ­ 800 mhz ­ 800 mhz ­ 2.5 ghz ­ 12.5 ghz ­ 34 ghz calibration method trm trl trl trl lrl calibration standards fixed termination 15cm air line 5cm air line 5cm 6cm air lines 5cm 5.3cm air lines note each kit also includes a set of adapters that is user specified per the option finder below see page 19 for details recommended accessories a050a digital connector gage kit thread-on type see page 92 8799a1 torque wrench 5/16-inch 8 in lbs see page 94 vna softwar ordering options to specify the test port adapter and vna software options you need simply add two digits to the end of the kit model number as shown in the diagram at right the first digit is the test port adapter option number and the second is the vna software option number as found in the option finder below the example in the diagram shows the combination of digits needed to order a 8060a kit configured with the adapters and software for use with an agilent pna that has 3.5mm or 2.92mm k test ports 8060a1 7 test port adapter option kit model number option finder vna test port type 3.5mm 3.5mm or 2.92mm k 1 1.85mm or 2.4mm 1 test port adapter kits w/o options software see page 19 option 0 0 1 2 10 20 rohde schwarz zv series option 1 01 11 21 vna software options agilent agilent 8510c 8719/20/22 option 4 option 5 04 05 14 15 24 25 agilent pna series option 7 07 17 27 anritsu 37000 option 9 09 19 29 1 1.85mm and 2.4mm connectors are fully mateable as are 2.92mm k and 3.5mm connectors the resulting junction is calibrated out and is not critical key literature maury data sheet 2z-045 maury microwave corporation 18 vna calibration kits microwave components adapters

[close]