AM/FM Tuner Module by McIntosh Laboratory, Inc.

More catalogs by McIntosh Laboratory, Inc. | AM/FM Tuner Module | 13 pages | 2006-11-29

Ads

Contacts for McIntosh Laboratory, Inc.

AM/FM Tuner Module is listed under these categories

Consumer Electronics > Home Audio > Tuners AM/FM

Featured catalog pages of AM/FM Tuner Module

McIntosh Laboratory, Inc., AM/FM Tuner

am/fm tuner module tm1 dealer installation guide mcintosh laboratory inc 2 chambers street binghamton new york 13903-2699 phone 607-723-3512 fax

overview the mcintosh tm1 am/fm tuner module adds am/fm broadcast reception to the mx119 mx134 or mx135 a/v control centers the mht series a/v system controllers c45 audio control center and other mcintosh components it also adds functionality of a second tuner to the mr85 am/fm tuner follow the instructions in this guide for installing the tm1 into the mx119 mx134 mx135 mht series c45 mr85 and other mcintosh components the tm1 tuner module is not a user installable product it must be installed by the technical professionals at your mcintosh dealer table of contents overview 2 please take a moment 2 technical assistance and customer service 2 important information 2 table of contents 2 parts list 3 connector information 3 mx119 mx134 or mx135 installation instructions 4 mht series installation instructions 6 c45 installation instructions 8 mr85 installation instructions 10 please take a moment the serial number installation date and dealer name are important to

parts list and connector information parts list part number 049084 034134 049192 049443 171404 171405 171406 description figure number am/fm tuner module 1 anti-static bag 1 raa1 remote am antenna 2 raa1 connection cable complete 2 seven conductor ribbon cable 1 six conductor ribbon cable 1 four conductor ribbon cable 1 tm1 serial number label 1 connector information raa1 connectors connect the shield and two leads of a shielded 2 conductor cable to the supplied 5 pin terminal connector plug refer to the connection information on the top cover of the raa1 if there is need to make-up a longer cable use a two conductor shielded wire and the connectors below 5 pinterminal connector 1 n/c red 2 n/c 3 red wiire 1 4 black wire 5 green wire shield black green 5 am/fm tuner module tuner module connecting cables tm1 serial number label figure 1 anti-static bag 7 pin din connector 1 red wire 2 black wire 3 n/c 4 n/c 5 n/c 6 jumper from pin 7 7 green wire shield and jumper to pin 6 raa1 remote

mx119 mx134 or mx135 removing covers 1 remove all connecting cables from the rear panel of the mx119 mx134 or mx135 cover screws a/v controller 2 remove two screws from each side and two screws from the back that secure the top cover to the mx119 mx134 or mx135 3 lift off the top cover by grasping the rear sides of the top cover and lifting up and away from the mx119 mx134 or mx135 4 remove the inside connector cover which is secured with two phillips head screws and is lofigure 3 cated on the rear panel refer to figures 3 and 4 note retain the two screws as they will be used later to install the am/fm tuner module installing the cables and module 5 locate the three supplied ribbon cables from the shipping carton and attach the plug of the six conductor ribbon cable to the six pin socket j3 as indicated on the mx119 mx134 or mx135 data pc board refer to figure 1 on page 3 and figure 4 on this page note the six pin cable plug and pc board socket are keyed to attach only in one

mx119 mx134 or mx135 installation instructions closest to the mx119 mx134 or mx135 rear panel refer to figure 7 note the six pin cable plug and pc board socket are keyed to attach only in one direction do not force it on backward figure 9 13 in a similar fashion attach the plug of the four conductor ribbon cable coming from the four pin socket j2 as indicated on the mx119 mx134 or mx135 data pc board to the four pin socket j5 of the module which is the middle one of the three in-line connectors 14 also attach the remaining plug of the seven conductor ribbon cable coming from the seven pin socket j1 as indicated on the mx119 mx134 or mx135 data pc board to the seven pin socket j4 of the module which is located closest to the mx119 mx134 or mx135 front panel reinstalling cover and setup in the following steps the mx119 mx134 or mx135 setup feature will be accessed to select the country of operation for proper am and fm reception the setup mode is on-screen video based menu and it

mht series component removing covers 1 remove all connecting cables from the rear panel of the mht series a/v system controller 2 remove two screws from each cover side and two screws from the back screws that secure the top cover to the mht series component 3 lift off the top cover by grasping the rear sides of the top cover and lifting up and away from the mht series component 4 remove the inside connector figure 10 cover which is secured with two phillips head screws and is located on the rear panel refer to figures 10 and 11 note retain the two screws as they will be used later to install the am/fm tuner module installing the cables and module 5 locate the three supplied ribbon cables from the shipping carton and attach the plug of the six conductor ribbon cable to the six pin j3 as indicated on the mht series component main audio pc board refer to figures 1 on page 3 and 12 note the six pin cable plug and pc board socket are keyed to attach only in one direction do not force

mht series component installation instructions audio pc board to the four pin pc board socket j5 of the module j4 which is the middle j5 one of the three inline connectors j3 14 also attach the remaining plug of the seven conductor cables from am/fm ribbon cable main audio tuner coming from the pc board module seven pin socket figure 15 j1 as indicated on the mht series main component audio pc board to the seven pin pc board socket j4 of the module which is located closest to the mht series component front panel reinstalling cover and setup in the following steps the mht series component setup feature will be accessed to select the country of operation for proper am and fm reception the setup mode is onscreen video based menu and can be viewed by connecting the mht series component monitor a video output s-video or composite to a tv/monitor this will allow for verifying the tuner country setting 15 reinstall the mht series component top cover refer to steps 2 and 3 on page 5 16

c45 removing covers 1 remove all connecting cables from the rear panel of the c45 audio control center 2 remove two screws from each side and two screws from the back that secure the top cover to the c45 3 lift off the top cover by grasping the rear sides of the top cover and lifting up and away from the c45 4 remove the inside connector cover which is secured with two phillips head screws and is located on the rear panel refer to figures 18 19 and 20 note retain the two screws as they will be used later to install the am/fm tuner module cover screws figure 18 installing the cables and module 5 locate the three supplied ribbon cables from the shipping carton and attach the plug of the six conductor ribbon cable to the six pin socket j23 as indicated on the c45 main pc board refer to figure 1 rear panel inside on page 3 figures 20 and 21 on this page note the six pin cable plug and pc board socket are keyed to attach only in one direction do not force it on backward 9 remove the

c45 installation instructions four pin socket of the module which is the middle one of the three in-line connectors 14 also attach the remaining plug of the seven conductor ribbon cable coming from the seven pin socket j21 as indicated on the c45 data pc board to the seven pin socket of the module which is located closest to the c45 front panel din connector note refer to the c45 owner s manual for additional operational details tm1 label f connector reinstalling cover and setup in the following steps the c45 setup feature will be accessed to select the country of operation for proper am figure 22 and fm reception the setup mode is indicated on the cables front panel alphaj3 from numeric display main j5 refer to figures 24 pc 25 and 26 board j4 15 reinstall the c45 top cover refer to steps main pc 2 and 3 on j23 board page 3 16 reconnect the j22 hookup conj21 necting cables to the rear panel of the c45 am/fm tuner 17 place the c45 module main power switch to the figure 23 on

mr85 removing covers 1 remove all connecting cables from the rear panel of the mr85 am/fm tuner cover screws 2 remove two screws from each side and two screws from the back that secure the top cover to the mr85 3 lift off the top cover by grasping the rear sides of the top cover and lifting up and away from the mr85 4 remove the inside connector cover which is secured with two phillips head screws and is located on the rear panel refer to figures 27 and figure 27 28 note retain the two screws as they will be used later to install the am/fm tuner module installing the cables and module 5 locate the three supplied ribbon cables from the shipping carton and attach the plug of rear the six conductor ribbon cable to panel the six pin pc board socket j3 as inside indicated on the mr85 main pc board refer to figure 1 on page 3 and figures 29 31 note the six pin cable plug and pc board socket are keyed to attach only in one direction do not force it on backward 6 in a similar fashion

mr85 installation instructions 13 in a similar fashion attach the j3 plug of the four am/fm j5 conductor ribbon tuner cable coming module j4 from the six pin pc board socket cables from main audio j2 as indicated pc board on the mr85 main pc board to the four pin socket j5 of the module which is the middle one of the three in-line connectors 14 also attach the remaining plug of figure 33 the seven conductor ribbon cable coming from the seven pin pc board socket j1 as indicated on the mr85 main pc board to the seven pin socket j4 of the module which is located closest to the mr85 front panel reinstalling cover and operation check in the following steps the mr85 setup feature will be accessed to select the country of operation for proper am and fm reception the setup mode is indicated on the front panel alphanumeric display refer to figures 34 35 and 36 15 reinstall the mr85 top cover refer to steps 2 and 3 on page 10 16 reconnect the hookup connecting cables to the rear panel

mcintosh laboratory inc 2 chambers street binghamton ny 13903 the continuous improvement of its products is the policy of mcintosh laboratory incorporated who reserve the right to improve design without notice printed in the u.s.a mcintosh part no