Catalog: AM/FM Tuner Module | |
| panel of the mx119 mx134 or mx135 cover screws a/v controller 2 remove two screws from ... each side and two screws from the back that secure the top cover ... to the mx119 mx134 or mx135 3 lift off the top cover by grasping the ... which is secured with two phillips head screws and is lofigure 3 cated on the rear ... panel refer to figures 3 and 4 note retain the two screws as ... will be used later to install the am/fm tuner module installing the cables and module ... data pc board refer to figure 1 on page 3 and figure 4 on this page note the six ... to figure 6 9 remove the am/fm cables tuner module from connected the anti-static ... the lower opening of the mx119 cover screws mx134 or mx135 rear panel the cover was ... panel with the two phillips head f screws that were previc o ously removed from ... | |
| a/v system controller 2 remove two screws from each cover side and two screws ... from the back screws that secure the top cover to the mht ... series component 3 lift off the top cover by grasping the ... which is secured with two phillips head screws and is located on the rear panel refer ... figures 10 and 11 note retain the two screws as they will be used later to install ... the am/fm tuner module installing the cables and module ... pc board refer to figures 1 on page 3 and 12 note the six pin cable plug and ... installafigure 12 6 tion of the am/fm tuner module refer to figure 13 8 locate the ... am fm tuner module cables in the connected antito ... pc board static am/fm bag tuner there is module a tm1 serial number ... of the bag refer to figure 1 on page 3 remove the label from the bag and ... | |
| from am/fm ribbon cable main audio tuner coming from the pc board module seven ... this will allow for verifying the tuner country setting 15 reinstall the mht ... top cover refer to steps 2 and 3 on page 5 16 secure the mht series ... cover to the rear panel with the two screws that were previously removed 17 ... reinstall the four screws to the sides of the mht series ... remote control the on-screen menu item tuner indicates the current country setting ... of the tm1 am/fm tuner module if it needs to be changed to a ... figure 17 menu system setup 1 video 2 tuner 3 temp display 4 osd routing 5 video ... component model number followed by tuner usa or tuner europe or tuner japan ... operational setting for the tm1 am/fm tuner module is usa to check the current ... the following 23 verify the am and fm tuner is functioning properly figure 16 7 ... | |
| c45 audio control center 2 remove two screws from each side and two screws from the ... that secure the top cover to the c45 3 lift off the top cover by grasping the ... which is secured with two phillips head screws and is located on the rear panel refer ... 18 19 and 20 note retain the two screws as they will be used later to install ... the am/fm tuner module cover screws figure 18 installing the cables and ... to figure 1 rear panel inside on page 3 figures 20 and 21 on this page note the ... force it on backward 9 remove the am/fm tuner module from the anti-static bag refer ... to figure 1 on page 3 10 orient the module so the f ... rear panel with the two phillips head screws that were previously removed from the ... refer to figure 21 8 locate the am/fm tuner module in the anti-static bag there is ... | |
| from the rear panel of the mr85 am/fm tuner cover screws 2 remove two screws from ... each side and two screws from the back that secure the top cover ... to the mr85 3 lift off the top cover by grasping the ... which is secured with two phillips head screws and is located on the rear panel refer ... 27 and figure 27 28 note retain the two screws as they will be used later to install ... the am/fm tuner module installing the cables and module ... main pc board refer to figure 1 on page 3 and figures 29 31 note the six pin ... pc board 8 locate the am figure 29 fm tuner module in the anti-static bag there is ... bag refer to figure 1 on connector page 3 remove the label from the bag and ... am ant din connector refer to figure 30 9 remove the am/fm tuner module from ... -static bag refer to figure 1 on page 3 10 orient the module so the f f ... | |
