6 results for 4 pin connector plug found in 0.000 seconds

parts list and connector information parts list part number ... cable 1 tm1 serial number label 1 connector information raa1 connectors connect the ... 2 conductor cable to the supplied 5 pin terminal connector plug refer to the ... a two conductor shielded wire and the connectors below 5 pinterminal connector 1 n/c red ... 2 n/c 3 red wiire 1 4 black wire 5 green wire shield black ... number label figure 1 anti-static bag 7 pin din connector 1 red wire 2 black wire 3 ... n/c 4 n/c 5 n/c 6 jumper from pin 7 7 green wire shield and jumper to pin ...

and away from the mx119 mx134 or mx135 4 remove the inside connector cover which ... the rear panel refer to figures 3 and 4 note retain the two screws as they will ... from the shipping carton and attach the plug of the six conductor ribbon cable to ... the six pin socket j3 as indicated on the mx119 ... refer to figure 1 on page 3 and figure 4 on this page note the six pin cable ... plug and pc board socket are keyed to ... chassis opening labeled raa1 am ant din connector refer to figure 6 9 remove the am/fm ... 5 10 orient the module so the f connector that is panel bottom of the module rear ... cover was previously removed in step 4 and the three pc board connectors are ... secure the module to the tm1 label din connector mx119 mx134 or mx135 rear panel with ...

and away from the mht series component 4 remove the inside connector figure 10 ... from the shipping carton and attach the plug of the six conductor ribbon cable to ... the six pin j3 as indicated on the mht series ... figures 1 on page 3 and 12 note the six pin cable plug and pc board socket are ... 11 6 in a similar fashion attach the plug of the four conductor ribbon cable to ... the four pin pc board socket j2 and the plug of ... conductor ribbon cable to the seven pin pc board socket j1 7 relocate the ... the opening labeled raa1 am ant din connector refer to figure 14 9 remove the am/fm ... page 3 10 orient the module so the f connector that is at the bottom of the module ... cover was previously removed in step 4 and din the three pc board connectors ...

instructions audio pc board to the four pin pc board socket j5 of the module j4 ... the middle j5 one of the three inline connectors j3 14 also attach the remaining plug of ... coming from the pc board module seven pin socket figure 15 j1 as indicated on ... component audio pc board to the seven pin pc board socket j4 of the module which ... setup 1 video 2 tuner 3 temp display 4 osd routing 5 video format ntsc usa ...

and lifting up and away from the c45 4 remove the inside connector cover which ... from the shipping carton and attach the plug of the six conductor ribbon cable to ... the six pin socket j23 as indicated on the c45 ... 20 and 21 on this page note the six pin cable plug and pc board socket are ... cover was previously removed in step 4 and the three pc connections j23 board ... connectors for ribbon are facing up refer j22 ... removed from the rear panel in step 4 12 attach the plug of the six conductor ... ribbon cable coming from the six pin socket j23 as indicated on the c45 ... main pc board to the six pin socket of the module which is located ... panel refer to figure 23 note the six pin cable plug and pc board socket are ... 13 in a similar fashion attach the plug of the four conductor ribbon cable ...

and lifting up and away from the mr85 4 remove the inside connector cover which ... from the shipping carton and attach the plug of rear the six conductor ribbon cable ... to panel the six pin pc board socket j3 as inside ... page 3 and figures 29 31 note the six pin cable plug and pc board socket are ... 6 in a similar fashion attach the plug figure 28 of the four conductor ribbon ... rear panel openings cable to the four pin j2 and the plug of the seven ... conductor ribbon cable to the seven pin socket j1 7 relocate the free ends of ... din of the bag refer to figure 1 on connector page 3 remove the label from the bag ... the opening labeled raa1 am ant din connector refer to figure 30 9 remove the am/fm ... 3 10 orient the module so the f f connector connector that is at the bottom figure ...