Catalog: AM/FM Tuner Module
Company/Brand: McIntosh Laboratory, Inc.
5 pin din connector in AM/FM Tuner Module by McIntosh Laboratory, Inc.
parts list and connector information parts list part number ... cable 1 tm1 serial number label 1 connector information raa1 connectors connect the ... 2 conductor cable to the supplied 5 pin terminal connector plug refer to the ... a two conductor shielded wire and the connectors below 5 pinterminal connector 1 n/c red ... 2 n/c 3 red wiire 1 4 black wire 5 green wire shield black green 5 am/fm ... number label figure 1 anti-static bag 7 pin din connector 1 red wire 2 black wire 3 ... n/c 4 n/c 5 n/c 6 jumper from pin 7 7 green wire shield and jumper to pin ...
mx134 or mx135 4 remove the inside connector cover which is secured with two ... module installing the cables and module 5 locate the three supplied ribbon cables ... six conductor ribbon cable to the six pin socket j3 as indicated on the mx119 ... and figure 4 on this page note the six pin cable plug and pc board socket are ... the chassis opening labeled raa1 am ant din connector refer to figure 6 9 remove ... to pc board refer to figure 1 figure 5 10 orient the module so the f ... connector that is panel bottom of the module rear ... in step 4 and the three pc board connectors are facing up refer to figures 5 and 6 ... 11 secure the module to the tm1 label din connector mx119 mx134 or mx135 rear ... four conductor ribbon cable to the four pin pc board socket j2 and the plug of ...
series component 4 remove the inside connector figure 10 cover which is secured with ... module installing the cables and module 5 locate the three supplied ribbon cables ... six conductor ribbon cable to the six pin j3 as indicated on the mht series ... figures 1 on page 3 and 12 note the six pin cable plug and pc board socket are ... four conductor ribbon cable to the four pin pc board socket j2 and the plug of ... conductor ribbon cable to the seven pin pc board socket j1 7 relocate the ... below the opening labeled raa1 am ant din connector refer to figure 14 9 remove ... page 3 10 orient the module so the f connector that is at the bottom of the module ... was previously removed in step 4 and din the three pc board connectors connector ... head f screws that were previously connector removed from the rear panel in step 4 ...
away from the c45 4 remove the inside connector cover which is secured with two ... 18 installing the cables and module 5 locate the three supplied ribbon cables ... six conductor ribbon cable to the six pin socket j23 as indicated on the c45 ... 20 and 21 on this page note the six pin cable plug and pc board socket are ... and the three pc connections j23 board connectors for ribbon are facing up refer j22 ... ribbon cable coming from the six pin socket j23 as indicated on the c45 ... main pc board to the six pin socket of the module which is located ... panel refer to figure 23 note the six pin cable plug and pc board socket are ... ribbon cable coming from the four pin socket j22 as indicated on the c45 ... four conductor ribbon cable to the four pin pc board socket j22 and the plug ...
away from the mr85 4 remove the inside connector cover which is secured with two ... module installing the cables and module 5 locate the three supplied ribbon cables ... conductor ribbon cable to panel the six pin pc board socket j3 as inside ... page 3 and figures 29 31 note the six pin cable plug and pc board socket are ... rear panel openings cable to the four pin j2 and the plug of the seven ... conductor ribbon cable to the seven pin socket j1 7 relocate the free ends of ... label attached to the outside tm1 label din of the bag refer to figure 1 on ... connector page 3 remove the label from the bag ... below the opening labeled raa1 am ant din connector refer to figure 30 9 remove ... 3 10 orient the module so the f f connector connector that is at the bottom figure ...
